Nissan Tiida Versa Rear Light Bulb Replacement how to replace break light If this video has helped you, please subscribe to my channel. Appreciate your support. Thank you.
Пікірлер: 62
@jeremywheeler84174 жыл бұрын
I figured most of us out on my own, accept the housing was so hard to remove I thought it would break. Thanks for the video.
@alvarobastidas76568 жыл бұрын
This video is AWESOME I was able to change the light in my mom's car in four minutes, she was very worry and now she is very happy and I regained my favorite son status. thank you.
@serg3y7 жыл бұрын
I think we need laws to punish designers that come up with this s**t.
@anridapu6 ай бұрын
Absolutely correct! Very poor human engineering here. Almost like they designed the car then thought ‘Oh, we forgot to design access to replace the globes’🥴
@KensingtonBill7 жыл бұрын
Couldn't figure it out. Then watched your video and was able to replace the bulb in a few minutes. Great. Thanks very much !
@beshamshew4236Ай бұрын
Thank U.I just changed Mine.I appreciate it.🙏
@ulbrichtumАй бұрын
took two people to get the housing out of its final clip... just had to bang and pull. Thanks!
@bobafett75588 жыл бұрын
Thank you! I tried looking at it myself and couldn't figure out how to get to it. This video showed it very easily. I followed the steps, done in about 5 minutes. I took the most care in replacing the nuts so I didn't drop them. Thanks for taking the time to make and post this!
@geanbell37965 жыл бұрын
Than you. I'm a mechanical idiot and I appreciate the very clear instructions. Good tip on the magnet, didn't have a magnetized tool so I stuck a STRONG one on the base of my 10mm ratchet. Took less than 5 minutes after watching your video!
@chandlerkirkland4757 жыл бұрын
Very very good video. The last one i watched did not illustrate the steps. Yours shows every step directly and is very helpful
@keymatrix6 жыл бұрын
Great video! I only had a regular socket so I put it over the lower nut and then put the driver into the socket to turn it. I needed pliers for the upper nut because my wrench was too large. Learned a new skill today.
@jackavalon83664 жыл бұрын
Thanks. That was really useful. But I dropped the nut and ended up destroying the boot lining trying (unsuccessfully) to get it back. But yeah, your video was really helpful. Absolutely agree with Sergei K.
@careless_winner3 жыл бұрын
This man is a Godsend. Thanks for this.
@rknight43045 жыл бұрын
Thanks! I fixed my park light using this video. I used a bit of blutack at the end of the socket as I have a large hand and was paranoid about dropping the nut (for the back panel) when putting it back in as my socket wasn't magnetic.
@alejomerced214 жыл бұрын
Great advice on sliding the cover open. I popped it the first time and it cracked.. second time was better. Keep creating great content.
@darthbarmey64822 жыл бұрын
excellent instructions, I did the back up light on mine, a little fiddly, the key is to take your time, mine took 15 minutes, and managed not to drop the nuts.
@jackphan30715 жыл бұрын
I can do it. Thank you for Yours shows every step directly and is very helpful.
@saprissa98 жыл бұрын
thank you for your video. I had to do it for a company car and it look complicated until I watched your video.
@user-dm6lz4mb9i3 жыл бұрын
Отличное видео и комментарии. Thank you.
@enriquemartinez290411 ай бұрын
gracias amigo , saludos de México
@ZacchaeusNifong8 жыл бұрын
thanks a lot. really helped me figure this out.
@ThePurpleFaunusTM8 жыл бұрын
thank you! great job man.
@renata66677 жыл бұрын
Thank you! Very helpful! A women very proud ;-)
@bastienbouchard60168 жыл бұрын
thanks a lot. Very helpful!
@user-fu4ri3jb9e5 жыл бұрын
excellent video, thanks!!
@saitisaza30258 жыл бұрын
thanks for your help
@sgm14655 жыл бұрын
Thank you for the help
@Peppermint17 жыл бұрын
Could not figure it out without your help. A regular 10mm socket worked for me, not the deep one. For the upper nut I used a 10mm wrench, the ratchet won't work. Also no need to disconnect the wired, just pull the whole light assembly out.
@davidpatrick70295 жыл бұрын
Thanks so much!
@asifzarin4 жыл бұрын
Thanks Brother very nice and helpful video.
@ajaysingh7263 жыл бұрын
Thank you very helpful
@FEARWENDETA4 жыл бұрын
Thanks Bro! I use this lesson.
@MA-bn1xv8 жыл бұрын
thank you I saved $55
@ogrekogrek5 ай бұрын
thanks for the video, bdw where to look for the cap as I lost it
@luthercouch70686 жыл бұрын
good job
@artsycherry2290 Жыл бұрын
For some reason i’m stuck at the white electrical tube when removing the second nut. it just won’t come off and it’s super tight
@0RazMob07 жыл бұрын
how would you replace the front bulbs?
@clarissasheppard6241 Жыл бұрын
Is there running lights on a Nissan Versa 2008?
@wenjun87855 жыл бұрын
👍 看一次就會了
@peterlim23014 жыл бұрын
How long did you take to yank the housing from the body?
@nicholasaraos50893 жыл бұрын
Does anyone know what kind of bulb the brake lights use
@Jamesreidvids5 жыл бұрын
How about the front headlights pls
@yingcluk4 жыл бұрын
Just a friendly note. Do NOT use bare hands to touch light bulbs, there could be oil or grease on your hand to cause hot spot on the bulb, and it will burn out faster.
@biancaolszewski38288 жыл бұрын
I have a nissan tiida I tried to change the bulb but it did not work what could be wrong?
@tazman8697 Жыл бұрын
Hint: Put some superglue or grease in your socket so the nut sticks to the socket when working in tight spaces...
@Frenzel1107 ай бұрын
Thanks for the info
@ANTiViRUSplus8 жыл бұрын
what a huge bulb
@elnurtalibov82797 ай бұрын
👍👏👏👏
@ashleyhappenstotravel5 жыл бұрын
I cannot push the light off for the life of me. I don’t know how he does it so way with one hand. Had the same issue before when we had to replace a different bulb. Took it to a shop and it took like 4 guys to get the darn thing off.
@yingcluk4 жыл бұрын
Yeah, it was very hard to push that the light housing off. It took me a long time to get it. Like the video said, push inward (toward the car) and also backward at the same time. I would just beat the crap out of the designer whoever designed this crap. It's so hard to get to the screws, and it's so difficult to remove the housing.
@peterlim23014 жыл бұрын
@@yingcluk The housing is still waiting for me to yank it away from the car - it's been like 2 days since I removed the nuts. Wondering if I can spray a bit of WD40 to the screws to loosen them - how did most of you guys do it beside using brute force?
@fields13363 жыл бұрын
Light Burrg 😄
@crewmasscre25 жыл бұрын
I couldn't locate the damn light burb 😂😂😂
@jude999 Жыл бұрын
Wtf? I wonder why they make it so hard to do
@yoonhong90987 жыл бұрын
Oh. Fxxx Nissan! Unbelievably terrible design!
@anridapu6 ай бұрын
Yep, absolutely pathetic design!
@rahgahnah7 жыл бұрын
what a terrible design nissan! 10 MM deep socket to change the freaking taillight bulb... unbelievable.
@kacetechreview49787 жыл бұрын
Nissan purposely designed this way, so people will go to the dealer for this service.
@darthbarmey64822 жыл бұрын
@@kacetechreview4978 yep they can charge you $60 to change a bulb that costs less than $5, they are deigned to rip people off