How To Replace Rear Brakes & Rotors 2002-2011 Honda CRV

Рет қаралды 101,535

4 жыл бұрын

Here are some of the tools that jimthecarguy uses
www.amazon.com/shop/jimthecarguy
Nothing will be left out. Easy to follow step by step advice. Come along as I show you how to replace rear brakes and rotors on this 2006 Honda CRV.
Due to factors beyond the control of jimthecarguy, it cannot guarantee against unauthorized modifications of this information,. jimthecarguy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. jimthecarguy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of jimthecarguy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not jimthecarguy.

Пікірлер: 199

@bookreaderlabarr 4 жыл бұрын

I did my brakes and rotors recently had to use a 20lb sludge hammer to remove, I used enough anti seize to keep it from happening. My front end has new ones but when I press my brakes I can hear a clamping noice any idea. My rotors get replaced every other year here in Pennsylvania

@jimthecarguy 4 жыл бұрын

Contact me you are the winner jimthecarguy1@gmail.com .

@chickennugget6611 2 жыл бұрын

@@jimthecarguy I wonder if he ever replied

@yeffry Жыл бұрын

@@chickennugget6611probably not:(

@jayb8439 3 жыл бұрын

Jim you saved me a lot of money , even my wife is finally impressed with me 😁

@frankbeck9405 3 жыл бұрын

One of the best videos I've seen here. Clear instructions, list of tools, socket sizes, ..., the works. Great site.

@FloridaSunMitochondria Жыл бұрын

Easily the best CRV rear brake video on KZfaq…no comparison!

@sailinon1969 3 ай бұрын

@jimthecarguy I cannot thank you enough for the trick about using a drift to loosen up the two screws on the rotors! I have used your videos to change the brakes out on our Highlander and now our CRV, and I don’t even want to tell you what I did on my wife’s 1998 Honda Civic when I tried to change her rotors out. It has been a while, but I think I actually went to a confession to apologize for some of the words I used. Please keep on keeping on with your videos and sharing of knowledge. Sincerely, the universe.

@richardstewart-jones4155 3 жыл бұрын

Thanks Jim - keeping it simple, step by step. Like the way you show the parts that are a bit problematical, like getting clips to locate properly, rather than missing that part of the video and pretending it was all easy!

@user-vm5ys2fx4g Жыл бұрын

Jim, one of the best how-to videos I have ever seen! Made my brake job on the honda so much smoother and less frustrating. Very professional- thank you!

@alexandermolina1728 3 жыл бұрын

You need to keep doing videos. Many people can replace parts but not too many are good teachers. You are a good teacher. Keep up the good work and thanks for all your help

@John_GGG 3 жыл бұрын

Jim, I couldn’t have done it without you, seriously! I couldn’t get the rotor off on one side. One side was a challenge, the other side was not possible. I just beat the heck out of the second side and it finally came off, both sides done. New pads, rotors and calipers. For this job I had to use a bolt extractor and an impact tool, I was very skeptical but both worked great.

@darcyscott2406 Жыл бұрын

I just want to thank you Jim, after watching your video a couple of times I replaced the rear brake rotors and pads on my wife’s 2012 CRV. Come to fine out the person that did it last time bent the tabs over on the pads that fit into the caliper piston. Thanks Jim again, from Northwestern Vermont

@YOUZTUBE2000 4 жыл бұрын

...by the way Jim I missed hearing the street sounds of traffic and people walking by in your shop videos, lol you’re the Real Deal Jim! Thank you again Tony

@godygody8991 3 жыл бұрын

Very very professional job, I love to learn from people that really knows what are they doing 👍

@jet6581 4 жыл бұрын

Marc here, I've learned a lot from this channel and saved a ton of $$$. Thanks, Jim for all the videos and insight. Idaho

@geeitsphil 4 жыл бұрын

Greetings from CA Jim! Perfect timing as my aunts CRV needs the brake pads changed. Thank you for the detailed video!

@Anthony1337 4 жыл бұрын

Thanks Jim, you’re like the father I never had walking me through the entire process. Excellent video!!

@jimthecarguy 4 жыл бұрын

Glad you enjoyed it.Thanks for watching.

@w4ame Жыл бұрын

Thank you! I’m was in the middle of a brake job on my CRV and forgot how the stainless clips were installed. I appreciate you Sir.

@YOUZTUBE2000 4 жыл бұрын

Thank you for giving back/paying it forward!!! Great instructional video Jim- Thank you Tony in Chicago

@eldoradony 4 жыл бұрын

I like your warning speech about the burning smell. I give the same speech every time I do a rotor replacement. New York

@ArnoldEhahounTheMasterTropical Жыл бұрын

Just finished mine. Took me 5 hours but I got it done. Props to you sir!

@billziegmond4943 4 жыл бұрын

Another great video. Old school on the ground with hand tools. Love it! McKeesport Pennsylvania

@manuallabor7193 4 жыл бұрын

From Austin Texas. I love your videos and I have learned alot from watching them.

@joehunglow2009 4 жыл бұрын

Jim you're an absolute champ, easy to follow and manage to successfully change both rears on my 2002 CR-V.

@jimthecarguy 4 жыл бұрын

Thanks for watching.

@knockdown7getup8osda28 3 жыл бұрын

JIm , Thanks for a great video. I just purchased a 2006 CR V and want to do the brakes myself. I've never done a brake job before but your step by step video really teaches how to do it right. I also have subscribed to your channel Thanks again!

@jimthecarguy 3 жыл бұрын

Glad it helped. If you run into any problems let me know I will try to help.

@knockdown7getup8osda28 3 жыл бұрын

@@jimthecarguy Thanks so much Jim.

@boraxsopanic2670 11 ай бұрын

Excellent video. You must be an instructor being so clear and methodical. Thank you.

@jimthecarguy 11 ай бұрын

Wow, thank you!

@smid2550 2 жыл бұрын

This is the most informative video on this procedure I've seen; good job!

@jimthecarguy 2 жыл бұрын

Glad it was helpful!

@JC-kw9wm Жыл бұрын

Was just looking for a refresher and found this, great video and very well explained...thank you !!!

@joevilla9814 4 жыл бұрын

Awesome job Mr. Jim! Like how thorough your videos are. Joe Villa, El Paso Tx.

@Inquisitor6321 4 жыл бұрын

Hailing from Virginia. Love your videos Jim. They have been very helpful to me.

@tisasanders7191 4 жыл бұрын

I just ordered the key fob tester thing you used in one of your videos because my car isn't working due to imobilizer issue! Love your videos! Thank you so much! ❤ Tisa Sanders in Arkansas!

@tpod6580 4 жыл бұрын

Your a great mechanic very smart and I’ve been following you for ever thanks Jim I live in Pennsylvania!!!

@anthonylawlor9130 8 ай бұрын

Don’t forget anti seize on hub face. Remove car from jack stands before test driving!!!! Excellent how to video, thanks.

@michaelgarcia1854 4 жыл бұрын

Love your videos. Always informative. Keep up the great work. El paso, Texas

@pvmpepsihax1449 3 жыл бұрын

Thank you soooooo so much for going into detail about removing the rotor. Helped me alot now that i got stuck!

@chriscannata8044 2 жыл бұрын

Well done video!!! First time ever someone didn't cut the corners on the small stuff....

@john-michaelbellamy1664 3 жыл бұрын

Really great videos. Appreciate your experience and clear method to both the videos and the example.

@dinkbuster1 3 жыл бұрын

Dude this video saved my ass! Those little screws that hold the rotor to the hub I could not bust them loose even with an impact driver, I done like you showed in the video and whacked on them a few times with a 3/8 extensions and a hammer and they came right loose, THANK YOU!

@terrykotschwar6876 3 жыл бұрын

You did a great description of installation of the brakes! I could have used the torque numbers, but otherwise a great job!

@ronadams3194 Жыл бұрын

14:22 As previously mentioned, everything about your video is great but the Torque spec's would have been better. Thanks for your help.

@shadetree6705 4 жыл бұрын

Thank you for another informative video, having the ability to do your own work can save people a lot of money. Washington.

@BM-ev9ig 4 жыл бұрын

Thanks Jimbo... I can now do my 2011 CRV.. Texas here.

@gimmeeone 4 жыл бұрын

Love how you teach! Helped me many times! Minnesota

@billstreber5194 4 жыл бұрын

Great video as always greetings from Rochester New York

@bw5970 3 жыл бұрын

Thank you for doing this. Very thorough. I undid the two 12mm screws and the caliper is loose but i can't pull it off. Could it have something to do with the piston?

@bossslapahoe 4 жыл бұрын

Great vid Jim, greetings from HOT Georgia!

@dfvel 2 жыл бұрын

Great tutorial. Made the job a quick one.

@johnaclark1 4 жыл бұрын

Always enjoy your videos, Jim. John -- North Carolina

@realname6586 2 жыл бұрын

Thank you Jim, the middle anti rattle clip; does it have to be changed every time? if not, does it need any kind of adjustments?

@TheDisgruntledMechanic 4 жыл бұрын

Just dropping in to say great video as always. I am from the state of confusion! Thanks Jim.

@lonwillis783 4 жыл бұрын

LOL LOL LOL LOL I thought Ohio was the land of confusion. Your near Pittsburgh right?

@TheDisgruntledMechanic 4 жыл бұрын

@@lonwillis783 actually other side of state.

@adilramzi3712 4 жыл бұрын

Thanks Jim for this new brake job. Virginia

@frankhowell8139 3 жыл бұрын

Excellent job explaining everything. Thanks so much!

@CrooksMcRae Жыл бұрын

Yo Jim your videos rock brother! Thanks!

@joejordan5879 4 жыл бұрын

Jim, thank you for another helpful video. Joe from California

@richardfolkman 4 жыл бұрын

Great job! Thanks for the chance to get your gift. Richard from Ft.Worth, Texas!

@Countrywild 4 жыл бұрын

Rotors are like my 08 Kia Rondo. Thanks btw for that video. The rears are a pain in the butt.

@dm7097 4 жыл бұрын

Always love watching your videos Jim! N.Y.

@jrvej 5 ай бұрын

Very nice video. Excellent explanation. Thanks

@MotownVideo 4 жыл бұрын

Great instructions Jim, greetings from Michigan!

@viewer54322 4 жыл бұрын

Always helpful and appreciate the shop talks. Florida

@DK-vx1zc 4 жыл бұрын

Thanks Jim, will help me on my 2006 CRV !

@kubikariYOU Жыл бұрын

Really good job on the video. Thanks!

@danzielinski672 Жыл бұрын

Bloody good vid mate very informative cheers!!!

@xing2809 Жыл бұрын

Great video! Such detailed information and much appreciated for your job well done. Thanks.

@stuartosborne5069 Жыл бұрын

Very good video! How many lbs of torque did you apply to the caliper bolts?

@edagarom1211 3 жыл бұрын

Hi Jim, really good tutorial, easy to follow and precise information. Wonder if you have a video to replace the brake shoes, also how to adjust them.

@LouIsFatAndSassy 2 жыл бұрын

Very good video. Just did mine for the first time. One question: shouldn’t I be using copper anti-seize on all of the metal-to-metal instead of silicone paste, just using the past for the guide pins?

@darrylbryans2524 2 жыл бұрын

Thx Jim, excellent video. Do I need to torque the bolts to a certain pressure?

@ahmadghosheh3104 4 жыл бұрын

Good video Jim. I always replace the rubber boots and slide pins on the caliber. Many pad kits comes with the boots and the pins are only $10 extra. This is especially important if the slide pin has a rubber ring at the bottom of the pin, those normally get swallon over time and make the slide get stuck.

@jimthecarguy 4 жыл бұрын

Thanks for watching. Hope all is well with you.

@wannabeelektwicityman268 4 жыл бұрын

Another great video. From South Carolina.

@mxjx462 Жыл бұрын

Great video! Nice step-for-step.

@jimthecarguy Жыл бұрын

Glad it was helpful!

@luisroca9947 4 жыл бұрын

Very helpful. Thank you Jim

@khbentaher 2 жыл бұрын

Thank you for this wonderful and very helpful video

@jimthecarguy 2 жыл бұрын

Glad it was helpful!

@melogrand 10 ай бұрын

Great video Jim, thank you!

@jimthecarguy 10 ай бұрын

Glad you enjoyed it

@codymorsell9835 3 жыл бұрын

Thank you so much. Great video, very helpful

@lonwillis783 4 жыл бұрын

Thank You Jim I am in Ohio It is the same for Honda element. I know its harder to work at home on something... Thank You So much for everything you do. and I ABSOLUTELY LOVED HEARING THE BIRDS SING IN THE BACKGROUND!

@sensations111 4 жыл бұрын

Nice work Jim! from Pennsylvania

@andrewdubman5132 Жыл бұрын

great video. Thank you!

@Johnny53kgb-nsa 4 жыл бұрын

Keep up the good work Jim, very interesting . Thanks, JohnG Indiana

@swavekbu4959 2 жыл бұрын

Thanks Jim, this is great, can you tell me why calipers might continuously fail? I've had to replace one caliper on my car about 3 times now, every time because it's leaking brake fluid. My mechanic has checked everything and is clueless as to why it keeps failing. All the other calipers have failed too, but the car is old, so I kind of expected that. (it's a 2002). But once replaced, it should last forever, no? After 40k miles, it fails again. Any thoughts of where I should look? Thank you! I think the caliper seizes up and it's producing friction, but I'm not sure if that's what's going on. I can't think of any other reason though, and why it would freeze up in the first place. Fairly new calipers.

@letsgofishingboys8756 2 жыл бұрын

Thanks Jim awesome video!

@jimthecarguy 2 жыл бұрын

You are very welcome

@Techman-yo5yv 4 жыл бұрын

You make it look so easy. Maryland.

@glb7471 3 жыл бұрын

Great video. Detailed.

@eriksilence9029 3 жыл бұрын

Great video. I would also check the brake fluid level after doing this😉

@twig3288 2 жыл бұрын

The fluid level should be checked before and after, if it's very full it could spill over when the caliper piston is pressed back.

@stevenyoung9049 4 жыл бұрын

Hi from Austin TX nice work

@sherryrybczynski1426 Жыл бұрын

Great video, thank you !What are the torque specs?

@davidc7313 4 жыл бұрын

Another great video. FL

@shamfrod 4 жыл бұрын

Great informative video! Texas.

@mikehernandez6528 4 жыл бұрын

Commenting in the right place now. - Mike from Tennessee

@jimthecarguy 4 жыл бұрын

This giveaway was held last night. In a few days there will be another one starting. Subscribe and hit the bell for notifications.

@danielkobylarz-lv8re 2 ай бұрын

Hi Jim.Do you unscrew the master cylinder cap when pushing the piston back in?

@chrisparenti2461 4 жыл бұрын

Another good video Jim. Chris from California. By the way, where’s your JACK STAND? that scissor jack had me nervous 😬

@manuelsalvatierra2940 4 жыл бұрын

Great info, Georgia

@erichelfrich1011 Жыл бұрын

When pushing the inner pad and clips into the brake caliper piston, HOW DO YOU MAKE SURE ITS ORIENTED/ALIGNED properly to mate with the brake disc,caliper hardware? Do the clips slide into CHANNELS INSIDE THE CALIPER PISTON? Please reply if you can ?

@netaipaul2964 2 жыл бұрын

Thanks great explanation.

@sakitlikod1 4 жыл бұрын

Great video, I just bought a 2004 crv and I can’t wait to do it myself...btw you have a video on how to adjust the valve lifters on 04 crv? Danny New York

@VM-wz9bg 4 жыл бұрын

Nice detail! New York.

@glenmckelvey5952 3 жыл бұрын

Great video thanks .

@nolesfan2769 2 жыл бұрын

Thank you!

@michaelhinchey 2 жыл бұрын

Does the sensor of the brake pad for on the top or bottom when putting them on?

@frankbeck9405 3 жыл бұрын

Jim: The pads I got went into a description of a "break in" procedure for new pads and rotors. Your thoughts? It described a series of stops, or more accurately slow downs, from 35 or 40, then more from a slower speed, then a drive around to cool down... I had never heard of this before???

@TheeNotoriousNic 3 жыл бұрын

What tool was that you used to compress the piston? What's it called?

@GeorgeWPush 10 ай бұрын

what is an alternative to using the piston pusher tool?

@thomastommy1192 4 жыл бұрын

As always a great video in great detail. Thank you for sharing your video. I truly hope you are having a Blessed Summer. I would like to inter in the camera contest also. MARYLAND. USA.