No video

How to Replace the Friction Pack on the RS800 CVT Transmission

  Рет қаралды 4,720

Sears PartsDirect

Sears PartsDirect

Күн бұрын

This #diy #repair video shows how to replace the friction pack on a common RS800 CVT transaxle made by General Transmission. You'll need to replace the friction pack for loss or neutral or loss of drive in the riding mower.
Order the replacement friction pack from www.searsparts...
To have a Sears Technician replace the friction pack or repair your riding mower, schedule service online at www.searshomes...
Transcript:
The next repair that we’re going to do is to replace the friction pack. This is on a fender-shifted unit with either a loss of neutral or loss of drive. To replace the friction pack, we must remove the driven kit and the drive kit - and we refer to other videos for those repairs (remove the driven kit -- • How to Replace the Dri... and remove the driver kit -- • How to Replace the Dri... ). We’ve now removed the driven kit and the drive kit so now we’re going to remove the top cover, C-clips, shift arm and the friction pack. We remove all of the screws. We remove the C-clip, shift arm and the cover. There are 4 screws holding the friction pack. The best way to reach the one under the cam is to simply rotate this out of the way to get access. To get access to the bolt, we must remove the spring. You’ve got to rotate the cam. Then the friction pack comes off. The new friction pack is shipped with the pin. Training Bulletin TB71-59 will explain the removal of the pin (TB71-59 instructs you to set control lever in Neutral and connect the control arm to the transaxle - YOU MUST REMOVE THE SHIPPING PIN IMMEDIATELY AFTER ATTACHING THE CONTROL ARM - DON’T LEAVE THE SHIPPING PIN IN PLACE OR YOU WILL DAMAGE PARTS). At this time, we reinstall the friction pack. Tighten the screws. Reassembly starts with the cam holding the selector. It slides into place. Then reset the spring. The measurement between the spring must be 2.5 inches. The next step is the cover. Tightening torque should be 2.5 ft-lbs. Reattach the shift lever. Install the C-clip. Remove the pin. We have now reinstalled the drive kit and the driven kit.

Пікірлер: 1
@DaveKitzman
@DaveKitzman 9 күн бұрын
I can't get mine to go into reverse it's like its blocked someway. Is there a reverse lock thats not releasing?
How to Replace the Driver Unit on a CVT Transmission of a Riding Mower
2:20
RS800 Full Disassembly
8:07
Husqvarna Training
Рет қаралды 30 М.
English or Spanish 🤣
00:16
GL Show
Рет қаралды 7 МЛН
Please Help Barry Choose His Real Son
00:23
Garri Creative
Рет қаралды 23 МЛН
I Just Bought a Tesla and It Scares the Crap Out of Me
10:23
Scotty Kilmer
Рет қаралды 101 М.
How to Replace the Driven Unit in a CVT Transmission of a Riding Mower
5:44
NEW HVAC Maintenance  - Flushing the Condensate Line
1:46
Providence Homes
Рет қаралды 31 М.
How to clean a variator on a RS800 transmission V3
4:34
REBECA MCALEXANDER-WILHELM
Рет қаралды 44 М.
China | Can you solve this ? | A Nice Math Olympiad Algebra Problem
12:52
Here Are 6 (or 7?) Car Brands That Will Fail
21:07
Doug DeMuro
Рет қаралды 511 М.
How to Replace the Lid Lock on a Common Washer
3:24
Sears PartsDirect
Рет қаралды 1,1 М.
Unclog Your AC Line in 5 Minutes with This Simple Trick!
3:52
Move Me To St. John's County Florida
Рет қаралды 11 М.
English or Spanish 🤣
00:16
GL Show
Рет қаралды 7 МЛН