For more information or a written out step by step you can stop by www.thediyguy.n... How to replace the lower element on a electric water heater.
Пікірлер: 260
@TheDIYGuyDOTnet5 жыл бұрын
It doesn't matter which wire goes were on the elements. As one wire has 120 volts on it and then when the element needs to heat the water the t-stat energizes the other wire with 120 volts and then makes the 220 volts used to heat the water. You can take a picture with your phone and put the wires back in the same spot if you would like to.
@racar30814 жыл бұрын
Thank you! I looked all over for this answer. Bless you!
@TheDIYGuyDOTnet4 жыл бұрын
@@racar3081 You're welcome, Glad we could help. Don't forget to give the video a thumbs up / like. Thanks
@HroduuulfSonOfHrodger3 жыл бұрын
@@TheDIYGuyDOTnet I'm about to attempt this and I'm following your video step by step. I do not see a valve "shut off" for the hot water going out of the heater. I see the valve for the cold water coming in though. If I follow the piping for the hot water, it branches off in many directions and some (but not all) of those red pipes have valves to turn off. There might be three valves out of five directions/branches to each sink/tub. Do I need to turn them all off? Or can I just skip this step? Or should I not proceed until I can locate a main valve to turn off? Maybe not all hot water heaters have this valve?
@HroduuulfSonOfHrodger3 жыл бұрын
@@TheDIYGuyDOTnet OK, just put the brand new part in and put everything back together and I'm still receiving the same E07 error code for the lower element and the screen is locked. I cannot press any buttons to try and clear the code manually. Looks like I need to call Whirlpool for help.
@jerrylisby53763 жыл бұрын
Can you clean a heating element?
@edrickett9827 Жыл бұрын
Taking the old element out and replacing it with the new one fast without draining the tank sure made it a lot easier. That was pretty cool. Thank you.
@charlenesessionskandl54013 жыл бұрын
A great, straightforward how-to video. These days I have much more time than money and no one around that’s handier (or more willing) than me. I determined the size of the necessary element by the model number of my old US Craftsmaster 120v water heater. It ends in 15, which indicates I needed a 1500W element. Thanks for making the video. Go, handy people!
@boom_bacon48962 жыл бұрын
You sir are doing the lords work. Saving all us broke diy dads some much needed money
@elishab65214 жыл бұрын
Whew! Glad I watched this video before tackling our tank. Husband is usually the handyman around here but he works long hours and isn't home much so I'm working on this project myself. Thanks for the help!
@jayray6104 жыл бұрын
Elisha Benson get it girl 😎
@cammyaustralis4 жыл бұрын
Jay Ray you dirty dog!!
@Helljumper10002 жыл бұрын
😍😍😍😍🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄🙄😬🥰😬🥰🥰😬😬🥰
@levislone55943 жыл бұрын
Thank you!! Not all of us had someone to teach us young bucks how to do this!
@DebbieTomkoSUNSHINE Жыл бұрын
I recently made an appointment with a plumber to service our tank-drain, check, fill and I was told since we had a boiler heating system, a plumber specialized in that area could only do the service.
@alansmith39843 жыл бұрын
Did you block the sound when changing the element because you were cursing. I usually curse during this moment.
@donmichaelcorbin44178 ай бұрын
I like to call them my power words...
@WalterMelons7 ай бұрын
lol no fkin way I’m doing it that way. I’ll drain it all. Get paid hourly so no rush.
@LittleChip912 жыл бұрын
Good info. The swap element while tank full method seems like it is risky for the novice. I prefer to drain the tank which is also a chance to flush our sediment. Plus the fast method looks like it could potentially leave wet insulation which could short positive and negative leads if the wet insulation touches both wires.
@TheShadeslayer212 жыл бұрын
Thank you! I thought this was a terrible Idea. This seems like it could lead to external rust issues. Not to mention I doubt soaking the thermostat is good for it's health.
@DWBJosh Жыл бұрын
@@TheShadeslayer21 I saw this and still drained mine lol.. better safe then lazy, I mean safe then sorry.. lol
@franciscambron Жыл бұрын
Not to mention all that soggy insulation packed back inside the water heater...
@damon323 Жыл бұрын
@@TheShadeslayer21 Ok, I’m glad I saw the comments here. I was thinking why not just drain the tank instead of rushing to jam a new element in. Especially when you gotta make sure you get the old gasket out.
@mathman0101 Жыл бұрын
The technique is what pros do where time is of the essence. Plus you are not wasting a whole tank of water. One improvement would be to jam an old towel doubled up around the opening that way the water leaks onto the towel. It takes a little bit of practice and the slight vacuum up top will only allow the water to gulp out not rush out. Reducing water spillage. Do it fast enough and the towel will hardly get wet.
@ickess3 жыл бұрын
I plan on draining my tank this weekend. I’ll take that opportunity to check my elements. Just seems easier and dryer with less of a chance of electrocution.
@Dezwrr4 жыл бұрын
Men I really appreciate you sharing this video. I just installed the element in my hot water heater.💯
@TheDIYGuyDOTnet4 жыл бұрын
You're welcome, Glad we could help get your water heater back up and running. Thanks for watching and taking time to leave us a comment. Don't forget to give the video a thumbs up/ like if you haven't already. Thanks
@stevewilliamson8526 Жыл бұрын
Great advice and instructions, I called my landlord 10 times, and he didn't answer and then I realized I was the landlord, but we saved him [me] a pile of money. My lower element has so much calcium build up around it [twenty years old] that I could not do the fast swap method but would do it on the top one, I have very hard water.
@serenagooch2 жыл бұрын
Exactly what I needed. Didn't know the size socket required as I had damaged the tool I bought specifically for removing elements. I'll be taking that back to the store, and heading to the local auto shop for the 1 1/2" socket!
@dannyjr7997 Жыл бұрын
Good luck bc mine was seized.
@codysellers53583 жыл бұрын
Great video, one thing I’d like to add if you have an old water heater with a good bit of build up. Just forget them channel lock pliers, go with the socket I definitely filled up the swear jar on this job
@jonathankhuzkian64192 жыл бұрын
Thanks for the tip, lol. Ive hard water, and the buildup is unreal.
@relerfordable2 жыл бұрын
This video was right on the money. While looking closely to the left of the upper thermostat I notice a wire partly embedded in foam insulation and a retaining clip oxidized where it had cut the wire casing. I found the cause of the no heat. I didn't do registration of the product three years ago. Off to buy a new Rheem water heater.
@beasthietala30334 жыл бұрын
Calm, steps given with reasoning behind it making this information very easy to understand. Thank you sir.
@TheDIYGuyDOTnet4 жыл бұрын
Your're welcome. Thanks for watching and taking the time to leave us a comment. Don't forget to give the video a thumbs up/ like if you haven't already. Thanks
@alfredo56932 жыл бұрын
Great video simple to follow both for the elements replacement and thermostat jus one word of advise getting that element off without a good socket and breaker bar is nearly impossible the tool the sell that looks like a tube slips and slides no leverage bought a socket for it and a breaker it it popped right off with a little effort probably not all of these water heaters may be as tight but just a heads up follow this video and have the right tool to get this out it will save you money 💰 and headaches again thanks for the video.
@Claiboren2 жыл бұрын
Don't forget to close the pressure relief valve when you have finished draining off the top of the tank!
@dadalone8 Жыл бұрын
Not draining the tank may be faster but you soaked the insulation and got water between the tank and the casing. A sure way to rust out the bottom of the tank.
@PAPATexas3 жыл бұрын
How many plumbers know this but still tell you to replace the whole thing!
@iancampbell5823 жыл бұрын
Maybe in America but not in my country!
@michaelcowan62542 жыл бұрын
Do not do it this way. Drain your tank or you will have a big mess. I always drained my tank and I am glad that I did this weekend. My lower element needed changing. I drain the tank and removed the old element. Went to install the new element, but could not get the threads to start properly. No matter what I did, it would not thread into the tank. I went to a different store and bought another element and it screwed right in without any issues. I have replaced about 6 elements and this was the first bad one. The threads on the bad one looked good, so it must of been machined wrong. Luckily no mess for me to clean up.
@SethHollingshead Жыл бұрын
So do you put hose on ...then open the pressure valve? I haven't done it yet. Or before. I know prior steps and am a car guy and have many traits just hate plumbing
@michaelcowan6254 Жыл бұрын
@@SethHollingshead First turn off power to the water heater. Then turn off the water supply to the hot water heater. Then connect a hose to the drain valve and open the valve. Open the pressure relief valve and then wait until the tank drains. This can take awhile. Then change out the element. Close relief valve, close drain valve, remove drain hose. Turn on water supply and open a hot water valve in your sink or tub. This will let air out and allow the tank to fill up. Check for any leaks. Open each inside hot water valve to remove air from each one. Then turn on power to start heating up the water in the tank. Should start having hot water in about 30 minutes.
@baristabrian Жыл бұрын
Meh. An exception to the "rule." Most people won't encounter this. Easier for me to do a quick swap without draining the tank, which, for me, is not worth it. Just saying. As always, YMMV.
@williamh.jarvis679522 күн бұрын
I wonder if that is Dad's problem with his electric hot water heater, that "mineral buildup, located somewhere around or before the 5 minute mark, like what you showed me here. While we did test both elements at the terminals, receiving positive test results on both, that mineral buildup on the beginning of element will create short circuit!! I wonder if that might be the primary problem. Good point!!
@knowledgeispower6192 Жыл бұрын
When you do it the quick way any insulation that gets wet looses it's R-value. Just something to think consider.
@aprilsesser40852 жыл бұрын
I would advise to drain the tank. Hot water cane gushing out all over our bathroom.
@jonymanay4 жыл бұрын
Thankyou for the demo. Im about to give this a go today. My only concern is plugging the wires in straight away while its all still wet.
@TheDIYGuyDOTnet4 жыл бұрын
You're welcome. Plugging the wires in shouldn't be a problem you could always wait a bit before you restore the power. You could always get a garden hose and drain the entire tank. Either way be sure to run the closest faucet on hot to get all the air out of the tank so you don't burn out the top element.
@meseahunt3 жыл бұрын
hair dryer area then reinstall cover
@milotorres68943 жыл бұрын
Good point to address just fill tank to top check for leaks before turning back on at the breaker...
@davidl22814 жыл бұрын
Wouldn't it be better to drain the whole tank to get as much sediment out as possible? And even flush it some after drained before installing new elements?
@milotorres68943 жыл бұрын
Service calls in and out but your right completely avoid same issue of cause and effect flush yearly and check anode for deterioration every 3 to 5 yrs .
@sknerl3 жыл бұрын
Yeah, I find the cause is usually built up sediment. Why not clean the bottom of the tank? Perhaps this is why I am still running the same hardware store special water heater since 1996. Replace anode rod, filler tube, both thermostats...but seriously, it’s all cheap. Just keep it clean, maintain regularly.
@danman96423 жыл бұрын
Outside of the yearly drain and 3-5 year anode check is there any other maintenance you perform on your water heater?
@davidl22813 жыл бұрын
@@danman9642 if it's an electric water heater I would turn breaker off to the heater, check with a meter to make sure power is off, and then go through all electrical connections to make sure all is tight. Don't over tighten anything, well before you tighten make sure all wires are in slots correctly, If gas check all piping with some soapy water to see if any leaks are present, they probably make something to check for gas leaks also but soapy water sprayed on usually works n if leaks are there it will blow bubbles. Im not a professional, just a diy guy if I can,. Im sure someone who is HVAC qualified can tell ya more, read your manual 1st also. Anyway just trying to help, good luck.
@sknerl3 жыл бұрын
@@danman9642 I have a set up for my shop vac to clean sediment from the bottoms of the tank. I try to clean that yearly and flush it in between. There are times it was double that. It allows you an opportunity to use a flashlight, open up an element, confirm dip tube is still functional. I have replaced mine after noticing half was missing lol. Strangely, I have only needed to replace the magnesium anode rod one time nearly five years ago. I do a check on the bottom element as it builds up crap between the element sides and shorts out. I’m guessing folks have different kinds of build up.mine is strong slaked lime. It fills the entire bottom and then some within a year.
@beotheguitarist5 жыл бұрын
Good video! Would be good if you showed how to troubleshoot to find out how you knew to replace the element.
@TheDIYGuyDOTnet5 жыл бұрын
Thanks. To test the lower element make sure the power is off to the water heater then grab an ohm meter and put in on the lowest ohm setting. Then touch each probe end of the ohm meter to each of the screw terminals on the heating element. If the element is good it should read between 10-16 ohms if I remember correctly. If you get lower or nothing at all then the heating element is bad. The problem for me and where I mostly worked was that the water was high in minerals/ iron so it would build up at the start of the element a lot more then in this video at the 5:30 mark and would give me a false reading. The signs of a bad lower element is you have good hot water at the start of a shower and then a few mins in it goes cold. You're start by using the top of the tank where the top element heated the water and then once you use that you get the colder water from the lower part of the tank where the lower heating element didn't heat it. You can get all the parts for less then 35$. New t-stats and elements. amzn.to/31hdEmq top t-stat. amzn.to/2Tb8wO2 lower t-stat. amzn.to/2Yra9Nr Element or a complete kit amzn.to/31lE6v0. So for around 35$ you could have a good reliable heater for a few years again assuming its not rusted.
@chrissherrill790 Жыл бұрын
@@TheDIYGuyDOTnetI got my insulation wet … is that bad?
@DWBJosh Жыл бұрын
All these videos make it look so easy loosening the damn element while my ass is over here about to just go buy a new water heater because I can’t get it out lol
@walterturpin1432 жыл бұрын
Great video, but there are 2 questions I think most DIYers would ask that aren't fully explained: 1. You very briefly mention draining the top of the tank. Seems like a vital step, but there is no instruction beyond your mention of it. A Google search for draining the "top" of the tank doesn't return anything more specific than how to drain your entire tank. 2. Is there any fear of the water gushing out being hot?
@RainOfBlue2 жыл бұрын
Any response to this shaky question? I'm more of a newbie to this. I need to know as much as I could. Thanks!
@daniellmartin91624 жыл бұрын
I have replaced the elements and just turned on the breaker. How long until we have hot water again?
@jacobpillow77574 жыл бұрын
It should take around 30 mins for a 40 gallon tank set at 125 degrees to have hot water
@milotorres68943 жыл бұрын
Hopefully you let it fill up all the way leave a faucet on the hot side till flows solid no air gaps then flip breaker on and wait half hour for hot water dry elements will burn up quite fast have to be replaced again...
@jmatherly9033 жыл бұрын
So glad the element is so close to the outside. Realistically, the SOB is 2 inches inside with the smallest workspace possible.
@LifeisGood8636 ай бұрын
Feb. 4th 2024... I just replaced my heating elements. I saved myself $500 🙏 only spent $40 for both elements 🤠
@thomasrebelo21895 ай бұрын
also useful to clean all the deposits at bottom of tank. Thats why is failed
@michaelroberts56442 жыл бұрын
Didn’t show how to release top for the air to water suction
@adrianzptb2 жыл бұрын
Thank you so much kind sir. Saved me from buying a new heater
@CommonSenseTipsAndTricks3 жыл бұрын
Thanks for the tips! You make it look so easy! I know it is if you take the right steps! Now to find that socket somewhere! Water Heaters are not cheap! Would Lowes sell the elements?
@dwho4322 жыл бұрын
Yes I just bought one tonight. 12$
@WhiteTurtleDiver Жыл бұрын
Dude! The element swap was hilarious, mad skills. Not trying that.
@MrBlakeW5 жыл бұрын
Just wondering why the mineral build-up wasn't cleaned out? That is one of the main reasons the bottom element shorts out. I have never had a top element short out.
@TheDIYGuyDOTnet5 жыл бұрын
There are a lot of people that don't flush there water heater to remove the sediment or mineral build up. This was an older water heater. I'm also sure that the anode was never replaced either. Water quality plays a big part. Yea top elements don't really go unless power is restored while the water level is below the element.
@fredbentley49445 жыл бұрын
When I was looking for the video I noticed there were none for the top element. Then I realized I have never had a top element go out either!
@jamescrossen15053 жыл бұрын
@@fredbentley4944 I just realized the same thing. My hot water keeps tripping the breaker, I took the covers off and the top one looked very corroded. The bottom one was replaced years ago, but the hot water tank has not been drained in a long time. After trying to get the top one out for awhile today with no luck I think my problem is the bottom one. Is it possible for the top one to go bad?
@2days2cents10 ай бұрын
I watched both your DIY videos on changing upper and lower thermostats, as well as this on on replacing the element. I was curious how do I know if I need to change out just the thermostats or the element or all 3? And do you always change out both thermostats? Thank you!
@DirtDoctors2 жыл бұрын
Thanks for the video. It’s very good for the DIYer just learning. So, what is the likelihood that both elements go out at the same time?
@epixtx01833 ай бұрын
I thought mine was leaking at the lower element gasket, but I looks like it is the flange the element screws into that is leaking, Is this repairable?
@mariesavannah23695 жыл бұрын
Praise God for the internet we wont need an electrician any more
@franchocou4 жыл бұрын
Carefull
@milotorres68943 жыл бұрын
Exercise caution no stored power like a capacitor can still bite after the unit is turned off and breaker is turned off overpaid wire pullers ICW they have many classification tack more $$$. Asking one for advice is not beneath me know hazards and potential ones for safety sakes...
@dumbass37706 жыл бұрын
Nice video great instructions easy to follow thanks
@TheDIYGuyDOTnet6 жыл бұрын
You're welcome, Glad we could help. Thanks for watching and taking the time to leave us a comment.
@emmkaa20993 жыл бұрын
This is absolutely perfect, thank you!
@georgem.3233 жыл бұрын
So if you see rust and you know the element is leaking is it potentially the element seal or possibly the tank itself? I am hesitant to touch it because I have a month to go before my hot water heater shows up. It has been ordered but delays are making it take longer. It is not an off the shelf hot water heater and has thicker foam insulation. I just pray the hotwater heater last long enough to get the new hot water heater here.
@wildeninja28362 жыл бұрын
So I just got a “tune up” kit that comes with both elements and two boxes with those plastic covers as well. Is it a good idea to just swap everything out while you’re there or wait until it fails? The code mine gave me was for the lower so I’m assuming it’s the rust like yours.
@claudevallee5072 жыл бұрын
Question is, when reconnecting wires to the new heater, does it matter what thermal is used? Thanks in advance..
@spn1025793 жыл бұрын
When you pull the bottom element without draining the tank and get water everywhere, I assume you have to wait a few days for it to dry off before powering it up??
@chrisE8152 жыл бұрын
Doubtful. Just make sure the terminals are dried off. Maybe run a de-humidifier next to the water heater for a week or so with the cover plates removed
@nursebunny74203 жыл бұрын
Wonderful Directions
@mgarde77482 ай бұрын
How do you turn off water lines? I know how to turn of the water coming into the house but uncertain how to turn off the hot water line going to the housr?
@karlaelvis98154 жыл бұрын
Great video... will be replacing my element today; thanks especially for the explanation regarding draining your tank vs. just the top... I will drain my entire tank, as my HW heater is in my art studio...
@nursebunny74203 жыл бұрын
Wonderful directions
@rossonphillips3 жыл бұрын
I have an older small tank with only the lower element 3000 watt. I replaced it with a 1500 watt same voltage. I also replaced the thermosat. No luck. Does a single element tank only work with the proper wattage element?
@dranyemonaidlasomar20313 жыл бұрын
...what's the size of the socket wrench???...
@jamiebarnes12413 жыл бұрын
1 1/2"
@toddwilliams2544 жыл бұрын
Checking for old gasket is a good point.
@TheDIYGuyDOTnet4 жыл бұрын
If there ends up being the old and the new it will seal up for a little while most of the time and then it will start to leak later on down the road.
@Hanover_outdoorsman2 жыл бұрын
Where does the ground rehook up to , my element was melted and can’t tell where it hooks up I have the same tank and I see the green ground wire going down twords element but not what it’s hooked to
@mattmiller26363 жыл бұрын
The only replacement elements I could find that were rated for my heater are doubled-over loops which are so heavy at the end that I cannot screw them in properly, even with a 1 1/2" socket. I can't get it threaded right. Any ideas besides completely disconnecting the wh and putting it on its side to install the new elements?
@coreydrake19332 жыл бұрын
My water heater doesn’t “hold” a lot of hot water. After like 2 normal length showers there is no hot water, and I have to hit that reset button each time cause it’s tripped. Then have to wait a good while till I have hot water again. Is that the element that needs changed ?
@RadhyRadhy962 жыл бұрын
we are manufacturing heater element in any size in any weight according to requirements.
@cathyfb Жыл бұрын
You said there is an upper element and a lower element. How do you know which one to change? I'm really new at this. Please help me.
@M70ACARRY4 ай бұрын
You can test the resistance of both elements and find the bad ones. As a homeowner, I'm changing both of them, even if only one is bad. They aren't terribly expensive.
@ssap37173 жыл бұрын
would the same socket size that removes the anode rod works for this?
@liltsummerlin4233 жыл бұрын
Thank you!! Something I can do myself 👏👏👏
@juliusguerra2172 жыл бұрын
Best video. Thanks
@aidentejada90662 жыл бұрын
Hi! The I replaced the lower element and the upper; I have the 220v on the upper but nothing on the lower. This is Normal?
@josevilca64934 жыл бұрын
very well explanation how to tested and how to take out and put in of the element. Could you please let me know what size is the socket to use for take out the element. Thanks a lot
@TheDIYGuyDOTnet4 жыл бұрын
You're welcome. Thanks for watching and taking the time to leave us a comment. Don't forget to give the video a thumbs up/ like. Thanks @ 4:21 . It is an 1 1/2" sized socket.
@PriscillaLong-gv6dm8 ай бұрын
I can't get.my old ones out. Any ideas
@fitch836311 ай бұрын
With that amount of material on the heater element I'm surprised you didn't remove the upper element and examine the anode to see if it might need replacement.
@mwngw4 жыл бұрын
Will that failing heating element cause the reset to be intermittently tripped (and not the circuit breaker)?
@peter26795 жыл бұрын
When the new element goes in how do you know what colour wire goes on which terminal?
@TheDIYGuyDOTnet5 жыл бұрын
It doesn't matter on the elements. As one wire has 120 volts on it and then when the element needs to heat the water the t-stat energizes the other wire with 120 volts and then makes the 220 volts used to heat the water.
@sgtJOOSEcapeS3 жыл бұрын
kzfaq.info/get/bejne/mcd_mZNhrta3mas.html
@sgtJOOSEcapeS3 жыл бұрын
The link will answer those other questions he didn't mention especially the ground and power wire's and the thermostat changing out real quick
@enjoythesho19924 ай бұрын
How do you know if just one element is bad ?
@tedrion64204 жыл бұрын
My water heater keeps shutting off ( not tripping the breaker ) I flip the breaker to get it to work again but then it shuts off quickly . Do you think I need new elements?
@croydonsfinest0073 жыл бұрын
Can I put a rheem thermostat and element on my Bradford as long as watts and voltage match up ?
@shafimehar45066 ай бұрын
Please tell the socket size which u used to loosen the element
@M70ACARRY4 ай бұрын
1.5 inch
@shafimehar45064 ай бұрын
@@M70ACARRY thank u sir
@constitutionsway2a3983 жыл бұрын
Any electric water heater to code should have a pigtail or electric disconnect ensuring there is no power, eliminating the need to shut off a breaker box…also any water heater located in the basement requires a T&P line ran to either a drain pan with a leak detector or a T&P line ran to an exterior wall with a escape to the outside.
@paulrodriguez320 Жыл бұрын
What causes the element to burn out. We've had our replaced twice in a year.
@thweethtoo3 жыл бұрын
My water heater is 10 years old. It make hot water but not enough to fill a tub. It on 50 gallon. What should I do? No leaking. Should I just replaced the whole thing?
@jamiebarnes12413 жыл бұрын
I would start with the thermostats and elements first. It's a much cheaper and easier job. You can get the tune up kit at Lowe's for under $30, and they're universal. Just make sure your wattage matches up.
@javierrendon99672 жыл бұрын
Once you change elements how long do you wait for water to heat up?
@thedesertdwellerfromutah43542 жыл бұрын
You can feel it getting warm at the faucet after about 30 minutes.... Should be Hot after about 45 minutes to an hour...
@noles06493 жыл бұрын
How long is the average heating element good for?
@thedesertdwellerfromutah43542 жыл бұрын
I replaced mine back in March.... A few days ago no more Hot water... Checked and the new heating element that I installed in March was already deteriorated and no good (Hard water here High Alkalinity) mine lasted 5 months
@EricInTampaAcoustic4 жыл бұрын
Do I need to drain the top tank if I replace the bottom heater element ?
@karlaelvis98154 жыл бұрын
Yes - he says so in the video
@EricInTampaAcoustic4 жыл бұрын
Karla Elvis I actually ended up draining the entire tank via the bottom valve with garden hose. Replaced the heater element with same rating but bigger service area one. I’ll follow suit with the upper one, too. It definitely was the culprit. I just hadn’t watched the e tire video. Thank you 😀
@karlaelvis98154 жыл бұрын
@@EricInTampaAcoustic I think that I may replace the top element as well, just because the tank is drained....
@EricInTampaAcoustic4 жыл бұрын
Karla Elvis I think I may do that as well... I already filled it back up with her new one but it’s only a bit warmer. Maybe it’s time for a new upper one now, too. It’ll one require to drain maybe ten gallons this time 😊😀☝️
@karlaelvis98154 жыл бұрын
@@EricInTampaAcoustic My bottom element was definitely the culprit - the top element was not as caked with alkali, but I replaced it anyway.
@PassionRedZX102 жыл бұрын
What if when I attempt to press the reset button on my electric heater, the button seems stuck. It doesn’t move
@jman53903 жыл бұрын
Do you have to put plumbing tape on it?
@PAPATexas3 жыл бұрын
Good info, thank you
@stevenjewett4537 Жыл бұрын
Thanks guy..❤
@live.shows.260 Жыл бұрын
How do you diagnose whether it's the upper or lower element?
@M70ACARRY4 ай бұрын
By checking resistance. You'll also likely have some hot water that quickly runs out when the bottom element is bad. Hot water comes from the top of the tank.
@davebriggs15896 жыл бұрын
Does it matter what wire I connect to each bolt
@TheDIYGuyDOTnet6 жыл бұрын
It doesn't matter as they both have 110v when energized so together will produce 220v and turn the element on.
@edpro19795 жыл бұрын
Thank you.I was wondering the same thing.@@TheDIYGuyDOTnet
@boleromientay37693 жыл бұрын
Thanks For sharing video, i will do by myself soon🙂🙂🙂
@luisalonso12493 жыл бұрын
I have 2 elements how do I figure out which one doesn’t work???
@jamiebarnes12413 жыл бұрын
Just change both. You can get a kit to replace both the thermostats and elements for under $30.
@1madrs6375 жыл бұрын
I have an electric water take like this one, at the bottom element panels there is a water puddle all at the bottom insulation right under the element, but the element isn’t what was leaking, any idea? Now my breaker won’t turn back on
@codydowntown195 жыл бұрын
1mad rs same problem
@1madrs6375 жыл бұрын
Nina Confidence called the warranty company and they said mine is bad, just got it replaced
@TheDIYGuyDOTnet5 жыл бұрын
I have seen many water heaters rust out where the heating element bung or nut that the element screws into is welded into the water heater tank. Mostly on Bradford and White heaters and mostly on the upper element. I would shut the power off two the heater, ensure that the heater is off with a test meter and then remove the covers and insulation and try and dry around both heating element bung/ nut areas upper and lower and then see if you can spot the leak. Check the MFG date and see if you still have a valid warranty and they will replace it.
@thewaterslesstraveled84875 жыл бұрын
I have a small 25 liter system that has a 2500 watt element, can i swap that out for a 1500 watt element without having to alter anything else on the system? (just trying to be nicer to my 3000 watt inverter).
@TheDIYGuyDOTnet4 жыл бұрын
You should be able to go down in wattage without a problem. If its a dual element you want to change them both to match. Just note that with a smaller element you will have a longer recovery time once the water is used as its a smaller element. While you will be pulling less wattage from the inverter it will be working longer as it will take longer to heat the water up.
@kingxtuna90054 жыл бұрын
What size is that socket before I unnecessarily buy 15 different large sockets.
@TheDIYGuyDOTnet4 жыл бұрын
@ 4:21 . It is an 1 1/2" sized socket.
@allenang95414 жыл бұрын
How do you know where to connect the yellow wire?
@TheDIYGuyDOTnet4 жыл бұрын
If you are talking about the yellow wire that goes to the elements it doesn't matter where on the element it goes as the water heater is 220 Volts, So both wires going to the element are 110 volts.
@milotorres68943 жыл бұрын
@@TheDIYGuyDOTnet thanks for the share helped clear the air never changed before just watched my dad many moons ago...
@Joetheg15 жыл бұрын
Is This is being replaced due to the hot water not lasting very long? For instance When showering, the hot water runs out after so many minutes then turns cold. . ??
@TheDIYGuyDOTnet5 жыл бұрын
Yes. As you are using the top half of the tank where the element has heated the water and then since the lower element is not heating the water the lower part of the tank is cold.
@marshallstrong78543 жыл бұрын
I found burnt wired at my heating element so we changed the element but still have a burning smell plz help
@screamingdean53 жыл бұрын
Is replacing the element the solution to a leaking water heater?
@2aquillus23 жыл бұрын
How old is the water heater? Unfortunately usually a leak means the water heater is totaled. Depending on the water pressure coming in from your city/town, the maintenance of the water heater, and your usage demands a residential water heater lasts 5 to 10 to 20 years. It might be time to get a new one but as far as appliances go they’re not too bad!
@screamingdean53 жыл бұрын
@@2aquillus2 Thanks for responding. I've since found out it wasn't the water heater that was leaking. It was a pipe under the kitchen sink not too far from the water heater. It took me a few days, but I was able to figure out how to stop the leak by shutting off a valve.
@craiglist3083 жыл бұрын
thanks, this helped.
@wanaraz4 жыл бұрын
How did you know it needed replacing? And why not run the water heater on just one element?
@TheDIYGuyDOTnet4 жыл бұрын
I knew because they said they start off taking a shower and after a few minutes it would go cold on them. You use the top of the tank first and then when that's gone it should start using the lower part of the tank. If the lower element doesn't work the lower part of the tank is cold and that's why you need both elements working.
@evenmattias3 жыл бұрын
Great video! Only problem is that I just became the guy my sister calls for everything wring with her house now
@JoseGutierrez-cg4wg4 жыл бұрын
Hey my friend what can cause to lose my power on my water heater.
@TheDIYGuyDOTnet4 жыл бұрын
It could be bad t-stats that caused the breaker to trip, a faulty breaker. Corroded wires, broke wire.
@JoseGutierrez-cg4wg4 жыл бұрын
@@TheDIYGuyDOTnet , thanks I'm working on.
@Cricketworld3074 жыл бұрын
I think it's better to replace the thermostat also if u gonna replace the element
@l.a.m7645 Жыл бұрын
What size socket?
@TheDIYGuyDOTnet Жыл бұрын
It would be an 1 1/2" socket. Here is an amazon link if you need to buy one. amzn.to/3XFO0VH
@raulgutierrez59204 жыл бұрын
Good job man you good👍👍👍
@TheDIYGuyDOTnet4 жыл бұрын
Thanks and thank you for watching and taking the time to leave us a comment. Don't forget to give the video a thumbs up/ like if you haven'y already. Thanks