How to Replace the Water Pump on a 2001 Ford Focus ZX3

Рет қаралды 153,076

8 жыл бұрын

Brian Eslick from How to Automotive www.howtoautomotive.com takes you step-by-step through the process of replacing the water pump on a 2001 Ford Focus ZX3.
Affiliate link mentioned in the video for 00-04 Ford Mercury 2.0 DOHC 16V ZETEC VIN 3, Z Timing Belt Kit GMB Water Pum amzn.to/2hMlL3A
Affiliate link mentioned in the video for Genuine Ford Fluid VC-3DIL-B Orange Pre-Diluted Antifreeze/Coolant - 1 Gallon amzn.to/2hDQ54m
Affiliate link mentioned in the video for Permatex 24300 Surface Insensitive Threadlocker Blue, 0.34 oz. amzn.to/2gzJGSN
Affiliate link for How to Automotive Tool Store www.amazon.com/shop/howtoauto...
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomotive.com/
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: How-to-Autom...
Google+: plus.google.com/+HowtoAutomot...
LinkedIn: / brian-eslick-819839118
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive

Пікірлер: 66

@Michiganborn1969 7 жыл бұрын

I'm glad you posted this video because so far it's the only one I could find on KZfaq that features the 2.0L Zeteck.

@HowtoAutomotive 7 жыл бұрын

Michiganborn1969 glad to help. Thank you for watching!!

@RavemasterX 5 жыл бұрын

Thanks a lot for this Brian, I've just done the job on my UK, right hand drive ST170, the layout was identical. I didn't bother taking the crank pulley off, still got the old pump out and the new one in fine. It took me about 4 hours just working on a driveway with the car on axle stands. The hardest bit was getting the belt back on!

@HowtoAutomotive 5 жыл бұрын

RavemasterX that Belt was a tough one. Glad it all worked out for you thank you for watching!

@michaelbearse4733 7 жыл бұрын

That's was the easiest way I've seen to do this!!! Very in formative!! And I learned something I didn't know! A new and much easier way to replace the water pump!

@HowtoAutomotive 7 жыл бұрын

michael bearse glad the video helped. Thank you for watching and writing!

@rotblauhacky 7 жыл бұрын

Gut gemacht Brian...ich werde es auch versuchen bei einem Focus 1,6 Zetec 2000 350000km ;-) Thanks a lot

@nooonehere 3 жыл бұрын

thanks...that saved me a ton of work!

@09bigbad 5 жыл бұрын

THANK YOU OMG THIS WAS THE BEST

@JoDaddysGarage 5 жыл бұрын

Good video. Thanks.

@Blastfence1 7 жыл бұрын

Excellent!

@NickBEADG 7 жыл бұрын

loosen the 3 bolts before removing the belt. the belt holds the pulley still.

@garage2track 6 жыл бұрын

Nick Truskowski that was exactly what I was thinking as I watched this

@Mikefngarage 5 жыл бұрын

my first thoughts

@D1amondeyes 4 жыл бұрын

Too late lol

@kentuckybowl-o-sticks 11 ай бұрын

UNLESS your pump got tight, causing the belt to come apart and take ITSELF off! : )

@JosafatAguilera 2 жыл бұрын

Great tut man, thx a lot!

@TACOPOTENTE 6 жыл бұрын

I am getting ready to do this on a Ford Focus ZTS 2004 2.3 LT, changing the water pump and serpentine belt !!

@HowtoAutomotive 6 жыл бұрын

TACOPOTENTE very cool let me know how it comes out.

@samuelgallagher9133 5 жыл бұрын

Thank you. Well done. Very helpful!

@HowtoAutomotive 5 жыл бұрын

Thank you. Did everything go smooth for you?

@johngodwin7902 7 жыл бұрын

great job. thanks for the help.

@HowtoAutomotive 7 жыл бұрын

John Godwin Glad to help John. Thank you for watching!

@jorgeuribe4512 6 жыл бұрын

the water pump pulley on my car is stock, it doesn't want to come off and I don't want to pry it off maybe it would bent, what can I do?

@tonylashmit2613 2 жыл бұрын

I did mine too but didn't need to takecoff the cranking pulley. I did mine before I had access to KZfaq and my repair manual didn't say you had to lower the engine to make room for the pump to clearthe frame rail,lol! I had to figure that out on my own.

@trickym5748 5 жыл бұрын

Looks like water pumps leaking on my st170 some good information here thanks

@Dude-gd5wm 8 жыл бұрын

Great vid, doing this my first time and just wondering if it matters that I line up the notches on the pulley cranks to the 12 o'clock position. One guy in a video did that but this way is much more efficient. Only reason I ask is he said it will damage the car if you don't. Thank you

@HowtoAutomotive 8 жыл бұрын

You definitely do not need to line it up at 12 o'clock. As long as it's the same Engine that's in this model. Possibly he may have had a different engine or different type of car. The only reason why you would need to line anything up is if you're doing a timing belt. If you could send me the link to the video you're watching I would be able to tell if it was the same job or not. Hope this helps thanks for watching!

@fahadnazir5856 7 жыл бұрын

This Lame guy and his cat. That video you are talking about the guy was referring to the timing chain and when you put the chain back on there is a notch on the pully that has to line up but only if your doing chain also water pump is easier

@jasoncarmichael1635 6 жыл бұрын

Thanks for the video! I don't want to critique but instead of taking off the timing pulley once you take off the motor mount and lowered the engine a tad the water pump pulley will fall right out. I think you only took off that pulley because maybe you didn't know you were going to have to take off the motor mount anyways, or at least that's what I'm thinking. Either way great video, thank you for taking the time to make it.

@HowtoAutomotive 6 жыл бұрын

Jason Carmichael Always welcome tips thank you. I can’t remember if I knew if the mount was coming out or not but it’s possible.

@astyxnax 2 жыл бұрын

Just did this yesterday. Taking out the motor mount completley definitely made it much easier.

@karloklil9587 5 жыл бұрын

Thw worker change water pomp But I affried he put timing belt wrong What I can do??

@mescnick 2 жыл бұрын

Helps

@TACOPOTENTE 6 жыл бұрын

I am still unable to remove the water pump does the battery need to be installed? Should there be any power running to the engine so that it unlatch whatever is holding this thing in?

@HowtoAutomotive 6 жыл бұрын

TACOPOTENTE when it comes to removing things if you're looking around and you feel like it would help you if you remove it I recommend that you do that.

@user-tc1og6ci3h 5 ай бұрын

Can i do this without a lifting platform?

@evullilbrat 7 жыл бұрын

Should I pre drain the fluid first so it won't rush out when I take the pump off

@HowtoAutomotive 7 жыл бұрын

EvulBrat you could pre-drain it would not hurt.

@evullilbrat 7 жыл бұрын

Thank you

@julicas76 5 жыл бұрын

thx

@HowtoAutomotive 5 жыл бұрын

Thank you for watching!

@TACOPOTENTE 6 жыл бұрын

Water pump has three screws they are off I’m getting some play however the old pump won’t just come out any suggestions?!

@HowtoAutomotive 6 жыл бұрын

TACOPOTENTE take a look at the brand new part and make sure there's not a fourth hidden Bolt

@TACOPOTENTE 6 жыл бұрын

How to Automotive Unless it’s invisible there is, however it plays as if there is a fourth something I can’t figure it out!

@TACOPOTENTE 6 жыл бұрын

*There is not.

@renezuniga9217 2 жыл бұрын

I. Need. To. The. Water. Pumps. Location. On a. 2.0l. Split port. 2002

@blass5506 4 жыл бұрын

To install the water pump I’ll need to use silicone??

@HowtoAutomotive 4 жыл бұрын

Blass No silicone. Just the O-ring that it comes with. If you add the silicone it will most likely leak.

@kentuckybowl-o-sticks 11 ай бұрын

I would just thinly coat the o-ring with silicone GREASE, not silicone SEALANT.

@jonware3929 8 жыл бұрын

I just fixed my 03s pump but it may be upside down

@HowtoAutomotive 8 жыл бұрын

What make you think that it upside down?

@jonware3929 8 жыл бұрын

In the video it showed it the opposite way

@marcpuystiens1355 7 жыл бұрын

Back again. Yesterday i got my new waterpump and after many looks at your video today i started to do it myself, but, how did you loosen up you cranck pulley bolt? It doesnt move a bit. Use WD40, blocked it, use a long metal tube to get more force. bussy for the whole day on that stupid Pulley. It is 19.00h and starting to get desperate... :(

@HowtoAutomotive 7 жыл бұрын

Marc Boretti I used an impact gun.

@marcpuystiens1355 7 жыл бұрын

00.24 done. His in. Instead of dropping the motor a few inches, i lift him up and did everything from above. Tomorow i will put the coolfluid in and see if i did the job good. (i hope the motor wont drop outa the car. Anyway... l still like your video. I learned new things again. (i am a chocolatier, not a garagist :) So tumbs up. Greetz from Belgium

@Omar-pb8lf 6 жыл бұрын

But that pump its to hard to come out thas the problem

@serieusmoat1937 7 жыл бұрын

Is that a diesel car? Guess it is the same as a 2002 1.8 tdci 115hp. First time i gona do this. Very great video, really.

@HowtoAutomotive 7 жыл бұрын

Serieus Moat! No it's not a diesel. Thank you for watching!

@RailroadGuy49 7 жыл бұрын

You kinda get your hands in the way of almost everything you're trying to point out, and in the beginning of the video, whatever you're doing is out of view of the frame.

@HowtoAutomotive 7 жыл бұрын

John Jensen it is a big learning curve to make these videos. This is one of my early ones for sure. Thank for the tips and thank you for watching!

@RailroadGuy49 7 жыл бұрын

How to Automotive absolutely sir! And thank you m!

@RailroadGuy49 7 жыл бұрын

Delete the m. Lol

@edwardmendez7392 5 жыл бұрын

Working on these fucking cars is a bitch and annoying i thought hey it ain’t connected to timing belt easy fuck that!! I miss my 89 civic hatch it took me 30 minutes