How To Replace Timing Belt & Water Pump on Honda Civic Sohc 96-00

Рет қаралды 127,259

4 жыл бұрын

Timing Belt/Water Pump Kit - amzn.to/2YTzbU1
OEM Honda Oil Pump Seal - amzn.to/2YQWWvZ
Continental AC Belt - amzn.to/31Acl5q
Pack of all 3 Accessory Belts - amzn.to/2Bu41to
Torque Specs D Series - www.nthefastlane.com/d-series...
Maxpeedingrods Parts I'm Using (Coilovers, Traction Bar, Splitter Brackets) - www.maxpeedingrods.com/?track...
Stainless Brake Lines I Like for Rear Disc Swapped Setups - amzn.to/3fXxdaQ
New EF Rack & Pinion That I Prefer - amzn.to/3hVEt93
Cameras used in this video
My GoPro - amzn.to/2YQ3OGZ
My Mirrorless Camera - amzn.to/2HzzFFT
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
/ garagebuilthondas
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for you support!

Пікірлер: 239

@leswire5859 2 жыл бұрын

Just a note if someone has not already mentioned. Loosen the camshaft gear bolt 1st before removing timing belt that way you don't have to block the gear, and you will not risk the camshaft rotating. Same when tighting. Looked at your video for a refresher before doing the job again. Thanks Great job.

@GarageBuiltHondas 2 жыл бұрын

👍

@omarchisolm7533 10 ай бұрын

@@GarageBuiltHondashello. Off topic but does this d series have a cam sensor? I'm getting a code for cam position sensor.

@nathanjohnson3790 Жыл бұрын

Outstanding Job Sir! I'm Quite Impressed How Well Yoy Explained Everything so well while holding your camera and doing the work while you Explained Everything!! I really felt like I was right there with YOU!! THANKS For Caring And Sharing!! Please Keep Up The GREAT WORK And Keep Them Coming!!!🙂🙂🙂

@skylerott8396 2 жыл бұрын

Dude your a life saver. ive always worked on a cummins diesel truck. but dont know jack about cars. this video helped me so much!! thanks

@GarageBuiltHondas 2 жыл бұрын

Glad to help!!

@frankpolowy8651 Жыл бұрын

Excellent video. The info we need and straight to the point! Thank you!

@jamesfitch1 2 ай бұрын

Exactly straight to the point. My how so many people like to talk and talk at the beginning of so many videos.

@AnticipatedHedgehog 4 жыл бұрын

Nice job man, straight forward guide. Would love some more light when showing certain bolts but I think we can follow along pretty well. I miss my EG hatch lol

@tigersnake72 3 жыл бұрын

This mechanic always put excellent videos

@Mr.smilez619 4 жыл бұрын

Digging the civic bro, wish i have a lot of room like that to work on cars. Stay safe and keep them videos coming

@GarageBuiltHondas 4 жыл бұрын

Thanks Alan. There's always some to work on!

@TndPnyRCofficial Жыл бұрын

This and the EricTheCarGuy video of timing belt replacement is quite a help for me. Been watching videos like this nonstop cuz I bought a Civic a few weeks ago and I wanna do a timing belt service on it. Mine doesn’t have AC nor power steering so the process is a bit quicker for me

@GarageBuiltHondas Жыл бұрын

Glad this helps! Let me know how it goes, you got this!

@TndPnyRCofficial Жыл бұрын

Thanks. It’s my first time doing actual work on my Civic cuz it’s my first Honda. As you can tell from my profile pic, I come from a Toyota 4Runner

@GarageBuiltHondas Жыл бұрын

You'll be just fine if you've worked on your Toy. 👍

@stevenbecker9988 Жыл бұрын

Thanks man this video saved me a ton of time and I didn't need allot of tools...

@GarageBuiltHondas Жыл бұрын

👍

@jamesfitch1 2 ай бұрын

This was a super informative video. My friends car needs this done so I’m glad I came across this.

@GarageBuiltHondas 2 ай бұрын

Glad it helped

@pmurriel2 Жыл бұрын

I'm doing mines now watch your video huge help 🎉

@Stomper 4 жыл бұрын

Liked how you gathered the parts at the end and put them the garbage. New endings approved.

@GarageBuiltHondas 4 жыл бұрын

😁

@xabysebastian529 4 жыл бұрын

More civic content please😎

@GarageBuiltHondas 4 жыл бұрын

👍

@Maplecook 11 ай бұрын

Thanks for posting vids like this, J! I've finally worked up the courage to do this myself next summer. (For a noob like me, that's saying something!) Of all the car guys out there, I love learning from you best, because you're the clearest, best lit, etc. Your explanation style fits my way of listening, perfectly. Forgive me if you said it in the video and I missed it, but the crank sensor is absent on the EF model, right? (It's located inside the dizzy?) Cheers, brother!

@GarageBuiltHondas 11 ай бұрын

Correct, don't have to worry about it on your car! 🙏

@Maplecook 11 ай бұрын

@@GarageBuiltHondas Thanks, man! ONE more reason to love the EF above all others! hahaha

@escondidonative2903 4 жыл бұрын

Great vid. Timing it is the hardest part

@GarageBuiltHondas 4 жыл бұрын

Thanks! Agreed!

@ubaldoalfaro6670 3 жыл бұрын

real helpful video thanx

@GarageBuiltHondas 3 жыл бұрын

👍

@EATSLEEPJD 3 жыл бұрын

Great channel you got going on sir :) Just discovered. Im a Texan also.

@GarageBuiltHondas 3 жыл бұрын

Thanks for watching, appreciate the comment!

@wopino 4 жыл бұрын

I love how thorough your vids are bro, great job homie

@GarageBuiltHondas 4 жыл бұрын

Thanks! Not really a fun video here but great for future usage. I've had a lot of people ask me for a D series timing belt video and finally had an opportunity to create one.

@wopino 4 жыл бұрын

@@GarageBuiltHondas all your vids are fuego bro, and always very informative 🔥🙌🤟🏼👊

@houstonskyline3815 2 жыл бұрын

🙌🏼

@lancelotkillz 3 жыл бұрын

Perfect step by step

@GarageBuiltHondas 3 жыл бұрын

👍

@lexsanchez8554 4 жыл бұрын

Nice walkthrough bro! And thanks! I think in my ef is more complicated cause am afraid to broke something 😂

@GarageBuiltHondas 4 жыл бұрын

Thank, you won't. It's Essen the same process and probably less as you may not have power steering or even AC.

@gabrieltiago6323 4 жыл бұрын

Thanks for Sharing! Regards

@GarageBuiltHondas 4 жыл бұрын

👍

@funkworthrollin4959 3 жыл бұрын

Oh boy. Tryin to do this and to find broken, missing, stripped bolts makes this alot of fun.

@GarageBuiltHondas 3 жыл бұрын

Ouch, thats a tough one.

@funkworthrollin4959 3 жыл бұрын

@@GarageBuiltHondas Yes. Sir. I give for the day. Time to play with son. LoL.

@GarageBuiltHondas 3 жыл бұрын

Thats how it goes. I do the same when frustrated or just tired of it.

@daNOSEthatKNOWS 2 жыл бұрын

great video

@GarageBuiltHondas 2 жыл бұрын

Thanks

@TndPnyRCofficial Жыл бұрын

Update: I just did the timing belt on my civic a couple of days ago. I thought it was hard but it was super easy. Didn’t change the water pump on mine cuz it wasn’t leaking and stuff. But my next timing belt change I will change out the water pump

@bryankylecueva1718 4 ай бұрын

hey sir the tensioner the pulley in there normally not rotatin? or no need to tighten the 14mm screw

@FroztiProductions 2 жыл бұрын

The service manual skips a few steps so Ima combine the manual with this video, thanks bro.

@GarageBuiltHondas 2 жыл бұрын

Hope it helps!

@cassidyphillips6631 12 күн бұрын

All seals snd gaskests i would meed for this job is it necessary to change the cam shaft seal ???

@iggyG31 3 жыл бұрын

Hey John i have a question on my d15b7 when i bring my Cam to TDC my crank is not lining up with the single line (next to the other 3) i can’t get both to match only either or , when i turn my crank to TDC i put my dipstick in cylinder #1 to verify piston is all the way up and it is not , I’d say it’s all the way down and I’m just trying to get motor in TDC before removing crank

@GarageBuiltHondas 3 жыл бұрын

Have you removed the belt and tried resetting timing?

@edgaravilac2753 9 ай бұрын

I hope people still see this ! If I wanted to just acces the Oil pump would I still have to remove every belt ? Or would the ones connected to the crank and alternator be enough to pull it off and proceed ?

@frankacosta1695 3 жыл бұрын

Good to learn how to fix certain vehicles

@GarageBuiltHondas 3 жыл бұрын

👍

@supratruck857 4 жыл бұрын

Nice video bro will buy a civic any time from u from ept on east side

@GarageBuiltHondas 4 жыл бұрын

👍 I just sold this one. Not sure when I'll have another one up for sale.

@supratruck857 4 жыл бұрын

The crx u sold 1500 was nice u left it clean congrats on your work

@theOGofREDS 4 күн бұрын

We only have 2 long and the 1 short bolts for the water pump. Where can I find a spare 3rd long bolt?

@mir5622 Жыл бұрын

Crank pulley bolt is seized in and now im not sure how to procede. Any advice? If i use a breaker bar it moves them from tdc so im kinda at a halt ty

@GarageBuiltHondas Жыл бұрын

Try heating the bolt and using some penetrating fluid to help loosen it.

@Fxybien 3 ай бұрын

Just bought a 1996 Civic and was looking at Rock Auto for the Continental Belts, i see two different A/C belts one that says Multi V-Belt and one that doesnt, was just wondering if theres any difference or if they would both work/fit.

@GarageBuiltHondas 2 ай бұрын

Rock Auto is great on fitment. If it says both fit you will be fine. One may be better constructed and expected to last longer.

@197VCK 4 жыл бұрын

I watched many d series timing belt videos including Eric the car guys before doing mine and in all of them they say the tension side of the belt should be on the exhaust manifold side, left side when looking at the cam gear dead on. You say it's the other way round. Who knows you may be right but I just thought I would mention it.

@GarageBuiltHondas 4 жыл бұрын

Interesting, thanks for the share. I've always removed my slack from the tensioner side. I had tried from the exhaust manifold side before and it was always a pain for me. It never worked out well the first few times. My method always works perfectly now. 👍

@Cypress_green Жыл бұрын

Do you replace the thermostat when doing this job? Mine is working fine so I'm not sure if I need to replace it while I'm doing the water pump..

@GarageBuiltHondas Жыл бұрын

I don't if it hadn't been an issue. You can always remove it and test it in a pot on the stove to make sure it's still opening.

@junioraugust8797 2 жыл бұрын

So when you spin the crank to get tdc you are also spinning the pulley above to tdc?. To take off the crank bolt with the 17 you dont have to put anything in the pulley to choke it from spinning losing from tdc ? Im just a little confused because he used a 17 to get tdc and then the same bolt that turned to get tdc was the one that came off to acces the waterpump. Please elaborate

@lifted4evr 2 жыл бұрын

Pretty sure he was able to go about it this way because he used an impact gun which broke that 17 loose and spun it back without cranking the pulley out of alignment to tdc. So if you're not using an impact gun like that you would have to use that Honda tool and a breaker bar to crank against eachother to break the 17 crank bolt loose while keeping the pulley in it's place.

@GarageBuiltHondas 2 жыл бұрын

Thanks for that response, perfect. I never saw his comment.

@chrisbrown5466 4 жыл бұрын

Great video but i never took out any spark plugs when i do my timing belts but every body is different

@GarageBuiltHondas 4 жыл бұрын

I meant plug wires. Lol

@balloney2175 3 жыл бұрын

Just deleted my negative comment. I actually learn from you... many thanks for posting!

@Rhadiqul 2 жыл бұрын

He’s a great guy!

@crelycxap23 3 жыл бұрын

My car is not timed it's off, and I was wondering if the tdc can still be used to time it back?

@GarageBuiltHondas 3 жыл бұрын

I don't understand the question.

@paulunnasch810 3 жыл бұрын

Yeah I live in Wisconsin. First step would be to spray P-Blaster on everything and let it sit overnight

@GarageBuiltHondas 3 жыл бұрын

Sounds about right

@luddfoee4180 3 жыл бұрын

When changine timing DO YOU HAVE TO REMOVE THAT OTHER COVER ? New to civic thing just wondering...

@GarageBuiltHondas 3 жыл бұрын

What "other cover"?

@fireinthehole72 2 жыл бұрын

Yeah I’m still not comfortable doing mine when the time comes. I’ll just save up and have it done by a pro. I don’t trust myself when it comes to timing lol

@realtalkrealtokes4823 11 ай бұрын

I just did it still not done spent 10 hours cause that oil gasket on the bottom.. then ran into the belt not fitting got the same one u got. I think I may have tightened the tensions will check tomorrow very helpful though I have a 99 civic but the belt before looks to be in perfect good condition you think it ok to reuse

@GarageBuiltHondas 11 ай бұрын

I've removed 100k+ belts that "look" ok. But structurally you don't know how much longer they last. I've also seemed snapped belts where all the teeth still look nice. I wouldn't reuse it. This belt is one of my favorites. amzn.to/3srfGDc

@iggyG31 4 жыл бұрын

Might be a silly question but is process same for the d16y8 ?

@GarageBuiltHondas 4 жыл бұрын

Exactly the same. 👍

@jessegunn2033 3 жыл бұрын

Hey I have a 97 Civic ex 5 speed need water pump and timing belt replacement do you know less how much a shop will charge??? Thx

@GarageBuiltHondas 3 жыл бұрын

No idea. They vary. You should call around and get some quotes.

@Blahbkah1289 2 жыл бұрын

How did you use a 19mm to get the crank bolt loose when it’s a 17?!?!? I have a 97 civic and I can’t get the bolt loose and I have the same Milwaukee drill as you,it’s driving my crazyyyy!!!!!!

@GarageBuiltHondas 2 жыл бұрын

It is a 17mm. I'm so used to working on my B series which are 19mm.

@Denver1976Man 2 жыл бұрын

Great video. Were u off one tooth. Bottom crank looked like it had moved a little to the right?

@GarageBuiltHondas 2 жыл бұрын

No. It was set correctly. 👍

@Farmstock24v 3 жыл бұрын

I just swapped a motor into my del sol, and every gasket is new.. didn’t think to replace water pump and yep, it’s leaking! I think I’m going to take it to a shop, I don’t wanna mess with pulling all of that off again 😂

@GarageBuiltHondas 3 жыл бұрын

Oh man. That's crappy

@bahena403 Ай бұрын

If your just doing the water pump, you dont have to remove the crank pulley?

@GarageBuiltHondas Ай бұрын

It's suggested to always replace the belt when the pump is replaced. I don't think you can access the pump without removing the pulley and the plastic cover.

@truthseeker1203 2 жыл бұрын

I’m changing timing belt on 97 accord lx 2.2 non vtec. I put it in top dead center. Took off the belts, and realized I didn’t make sure it was TDC for cylinder #1 specifically... checked the distributor rotor and its facing spark plug #1. So did I mess something up? Do I just put timing belt on as it is? What should I do?

@kymmedia2 Жыл бұрын

Will this help me if I skipped Timing or got codes P1399 p0304

@GarageBuiltHondas Жыл бұрын

I'd Google the codes first and see what usually fixes them.

@masterdebater0010 4 жыл бұрын

would you recommend rtv on the new seals?

@GarageBuiltHondas 4 жыл бұрын

No. It would only hide a leak. These seals should fit and do the job for many years to come if installed properly

@K1ngR3x 3 жыл бұрын

How good is the Continental kit? Time to do my 96 HX timing belt.

@GarageBuiltHondas 3 жыл бұрын

No issues so far

@lowbvll8969 3 жыл бұрын

Cleanest 1998 I’ve seen

@GarageBuiltHondas 3 жыл бұрын

👍

@lowbvll8969 3 жыл бұрын

@@GarageBuiltHondas trying do water pump on my d15b vtec lol thanks for a very good video!

@GarageBuiltHondas 3 жыл бұрын

Good luck, if you're willing I'm sure you'll get it done and learn a lot on the way.

@slouch2525 Жыл бұрын

Is this the same process on a 95 Honda civic EX?

@GarageBuiltHondas Жыл бұрын

Yes

@antonioj.gonzalez2085 2 жыл бұрын

Same belts you have for the d16y8 ?.

@GarageBuiltHondas 2 жыл бұрын

Y7 and Y8 are the same. 👍

@urbantek1 Жыл бұрын

when rotating the crank to TDC, are you turning it CW or CCW?

@GarageBuiltHondas Жыл бұрын

CCW

@urbantek1 Жыл бұрын

@@GarageBuiltHondas what happens if I went CW instead🙃 asking for a friend hahaha

@GarageBuiltHondas Жыл бұрын

It'll be fine. You just can't set timing properly that way. It won't do any damage.

@jasonyoung4890 3 жыл бұрын

Is that torque mount in bad shape? Mine on my civic is in bad shape like yours. Is that what could cause my car to shake while its at idle? I noticed it moves A LOT when i shift through the gears. This is my first honda and thought it was a motor mount

@GarageBuiltHondas 3 жыл бұрын

Usually the mounts are the issue, but these are cheap and easy to change and should be replaced if broken.

@Otsp922 2 жыл бұрын

What’s the proper name for those mounts when trying to find them oem Honda on a honda website such as honda parts now

@SmilinBastard 3 жыл бұрын

If you replace the water pump is it a must to replace any other seals or gaskets?

@SmilinBastard 3 жыл бұрын

I’m gonna need another motor sooner than later so I’m trying to do the minimum

@GarageBuiltHondas 3 жыл бұрын

Just the water pump gasket for sure. While you're there might as well do the cam and crank seal too.

@jclc4201 4 жыл бұрын

Hey man. New sub here. Can I ask for some advise where you get your JDM parts? You have a website or a shop where i can buy parts also? Thank you for your reply in advance.

@GarageBuiltHondas 4 жыл бұрын

Hey! Not anyway in particular actually. I scour eBay a lot for random things. You'll always see parts there. There's a handful of Instagram guys I follow who will ship. My main advice is don't shop unless ready to buy and money is ready and available. Be involved in your local Honda scene so you get notified of parts for sale. And be prepared to spend on shipping. Most parts you won't find locally. Good luck!

@jclc4201 4 жыл бұрын

@@GarageBuiltHondas thank you

@bobdavies2131 4 жыл бұрын

Are 1991 Accords A/C similar to this.?? Are you in west Texas.??

@GarageBuiltHondas 4 жыл бұрын

It should be similar. I'm in El Paso.

@reynaldorivera7641 4 жыл бұрын

I was driving the other day and saw you in the crv.

@GarageBuiltHondas 4 жыл бұрын

Nice! 👍 How's it look?

@reynaldorivera7641 4 жыл бұрын

Garage Built Hondas I like it

@GarageBuiltHondas 4 жыл бұрын

Thanks!

@reynaldorivera7641 4 жыл бұрын

Garage Built Hondas I been wanting to make my car into a track car. But still keep it as a daily so not going to crazy with it

@GarageBuiltHondas 4 жыл бұрын

What kind of car?

@spark6789 3 жыл бұрын

I have a 170k mile d16y8 do you recommend replacing the oil pump?

@GarageBuiltHondas 3 жыл бұрын

I've seen them last up to 250k miles. I don't recall the service interval but if you want to get more confident use from your engine, it would be smart to replace it now.

@spark6789 3 жыл бұрын

@@GarageBuiltHondas i appreciate it I've read the oil pumps are a weak link going to replace it. What is the tool called that goes around the crank and you put a ratchet on?

@GarageBuiltHondas 3 жыл бұрын

amzn.to/3m4F0rB

@blockedearth6537 2 жыл бұрын

Can I just put the belt straight on the cam or na I’m abit confused and scared

@GarageBuiltHondas 2 жыл бұрын

Only when it's set to TDC for the gear and crank pulley

@Thethe49er 3 жыл бұрын

Is this video similar to do for an 1998 honda ex?

@GarageBuiltHondas 3 жыл бұрын

Civic?

@Thethe49er 3 жыл бұрын

@@GarageBuiltHondas yes

@GarageBuiltHondas 3 жыл бұрын

Exactly the same.

@glendaturner7304 3 жыл бұрын

How long do it take to replace the water pump and how much do it cost give or take 🤔

@GarageBuiltHondas 3 жыл бұрын

Depends on the shop. Prices can vary greatly and the same goes for speed. I don't know how much shops charge, I haven't checked in ages. You may want to call and get an estimate. It took me 7 hours to do the job.

@gb361TX 4 жыл бұрын

Would this be the same process on a b16b?

@GarageBuiltHondas 4 жыл бұрын

This is a better video for dohc B. kzfaq.info/get/bejne/l9t7lMyAsLSzgGQ.html

@gb361TX 4 жыл бұрын

@@GarageBuiltHondas thanx brotha!

@samcox8941 2 жыл бұрын

Is this the same as an ef? I have a stock d15b

@GarageBuiltHondas 2 жыл бұрын

Pretty much identical without a crank sensor.

@razk5850 2 жыл бұрын

Does the 1.4l engine use the same pump/timing belt as the 1.6l engine

@GarageBuiltHondas 2 жыл бұрын

I do not know, sorry. I'm unfamiliar with the engine.

@razk5850 2 жыл бұрын

@@GarageBuiltHondas Can't find anything online, is there some wiki you're familiar with where I can search?

@1chineduutom 3 жыл бұрын

Is this the same process on a 1995 Honda Civic ?

@GarageBuiltHondas 3 жыл бұрын

Yes. Might be a few difference bolts but essentially example the same.

@1chineduutom 2 жыл бұрын

@@GarageBuiltHondas thanks man ! Love your videos !

@blueridge8992 4 жыл бұрын

Hey dude, I just got an insurance check so I’m asking advice from the Honda guys I follow and trust. I have $10k cash and I get to buy a weekend-only 2nd car and I’m surrounded by nothing but curvy mountain backroads with no traffic, even before the lockdown. It might see a drag strip or a few laps at VIR 2-3 times a year. SO, the best $3500 EG or EK sedan I can find on the East Coast and then $6500 in mods immediately (B18C/LS VTEC/B20 VTEC or maybe even an H, fresh clutch and maybe an LSD so I don’t have to pull the engine any time soon, wheels, tires, mild suspension, pads and rotors) OR a $9000 ‘13 Civic Si sedan with 100k miles and then spend $1000 on maintenance. If I go with the ‘13 then mods would be done $200-400 per month, so not super quickly. What would you do? Really appreciate your input and of course, your content! Keep up the great videos. I watch every single one.

@GarageBuiltHondas 4 жыл бұрын

I'd personally skip the newer car. Get an older one cleaner one already swapped. That's what I'd shoot for. Then spend the rest of the money on any mods/maintenance and have a super solid car. For 10k, you could find a really nice built Honda already.

@blueridge8992 4 жыл бұрын

Garage Built Hondas excellent advice. Thanks man.

@josephrivera636 Жыл бұрын

How long does it typically take to change?

@GarageBuiltHondas Жыл бұрын

4-6 Hours

@98Kentuckian 4 жыл бұрын

I probably need to do this on my EK but I think I'll just pay my mechanic to do it 😂 so much work

@GarageBuiltHondas 4 жыл бұрын

That works too!

@Moreno-123 Жыл бұрын

What size is your rims and tires ??????????

@GarageBuiltHondas Жыл бұрын

I'm unsure. This was a job I did on someone else's car.

@Peacefullsound1 2 жыл бұрын

You’re a fucking legend

@GarageBuiltHondas 2 жыл бұрын

👍

@Teedogmc Жыл бұрын

HOW IS THE TIMING BELT TENSIONED CORRECTLY? HOW DO YOU KEEP THE CAM FROM MOVING WHEN PULLING TIMING GEAR(TOP) AND CHANGING CAM SEAL???? IM GETTING READY TO DO THIS ON MY 96 BY16 ENGINE IDENTICAL TO THIS ONE. not yelling at you, lolooolol, caps for attention is all.

@dumper87 11 күн бұрын

Thanks. Just saved me from buying a ‘97 Civic.

@GarageBuiltHondas 11 күн бұрын

👍

@alkalionpower Жыл бұрын

make a b series video on this plz

@GarageBuiltHondas Жыл бұрын

kzfaq.info/get/bejne/erGlest_0Zilc6s.html

@TheRyanator36910 2 жыл бұрын

What trim level is this?

@GarageBuiltHondas 2 жыл бұрын

@poshpageboy8417 Жыл бұрын

Is this a D16 engine?

@GarageBuiltHondas Жыл бұрын

Yes

@matthewmoneypit1558 Жыл бұрын

Was way more difficult than I expected for what I thought was a older more simple motor.

@GarageBuiltHondas Жыл бұрын

It might look difficult but it's really not that hard once you start turning the wrenches.

@matthewmoneypit1558 Жыл бұрын

@@GarageBuiltHondas I just purchased this vehicle. Has 230,000 miles. No engine knock etc but really have no idea if this has ever been done. Was meant to be a secondary vehicle but is so much fun to drive as a 5 speed manual transmission that I want to make sure it gets the love it needs. Southern car so is in great condition and adult owned. Have interior out replacement of stereo for Bluetooth and factory speakers etc. Was getting water in trunk. Pretty sure I resolved. Rained all day and trunk is dry now. Changing transmission fluid tomorrow. Then Saturday shampooing interior. And working on new headliner for sunvisors My point is starting to burn out. Wish had purchased start of summer. No garage is my biggest problem.

@GarageBuiltHondas Жыл бұрын

Remove the valve cover and take a look at the timing belt. That'll give you some indication what shape it's in.

@matthewmoneypit1558 Жыл бұрын

@@GarageBuiltHondas Oh ok that's good idea. Thank you.

@SnowHerod Жыл бұрын

@@matthewmoneypit1558 How's it held up for you so far?

@219Fishing Жыл бұрын

Will be attempting to do this for the first time lol I’m definitely not looking forward to it .

@GarageBuiltHondas Жыл бұрын

Lop

@219Fishing 11 ай бұрын

I just changed my water pump and timing belt today thanks to your video . I appreciate it .

@samsung-eh4dv 2 жыл бұрын

Nice video it looks like it’s too much for me. I was quoted 285 not including the parts.

@GarageBuiltHondas 2 жыл бұрын

👍

@lny9233 Жыл бұрын

You forgot to say at compression at TDC

@dariusdarabant6232 2 жыл бұрын

How many hours whould you say that whis job would take?

@GarageBuiltHondas 2 жыл бұрын

Anywhere from 6 to 20.

@Mactime88 Жыл бұрын

How much did this job pay ?

@GarageBuiltHondas Жыл бұрын

This was my car at the time. I can't tell you how much people pay. Labor rates vary

@donkiko6708 3 жыл бұрын

I need to get that oil pump seal it keeps leaking

@GarageBuiltHondas 3 жыл бұрын

👍

@rjjones3490 Жыл бұрын

Bro. You literally skipped over the most important part of the video. Installing the timing belt 😕

@ediagautomotivetools4478 4 жыл бұрын

"If you have any sort of inquiry please leave a message on one of my videos." Just see it from you channel description,we would like to invite you test a DIY scan tool,Then we will send a email if interested to give a try.

@GarageBuiltHondas 4 жыл бұрын

I'm ok, but thanks for the offer.

@benhall8946 Жыл бұрын

You are explaining kind of how to tension the belt but you're not showing how to do it

@GarageBuiltHondas Жыл бұрын

Try tensioning it. If you haven't yet and are just watching videos, experience is the greatest teacher in life. Go outside and give it a shot. You'll get it.