I love how i got from never holding a screwdriver to having a giant arsenal of tools and learning every maintenance job needed for my car and bike through KZfaq because no one wanted to teach me. Everybody would offer to do it but nobody would let me do it myself. Thanks Ari for teaching a whole generation how to work on their own machines.

Despite already knowing how to change my brake pads I still watch this video as if I din't. As always informative and entretaining.

This is a most useful channel for bike lovers who like to maintain their ride.

just bought some new pads and will be changing mine out tomorrow for the first time. Thanks for the helpful tips and knowledge!

Also as a good habit/general rule of thumb...bleed the brakes with fresh fluid...or at the absolute minimum check your brake fuild and lines...

Very informative video! I always tell people to learn as much as the possibly can on their own. For one you will save a lot of money, two you can’t always trust just any old shop, three you can the knowledge and know what to look for, four the satisfaction of knowing you did it on your own and you did it right! Love these videos guys, Keep it up! 😄🙌🏻

This is probably the best video I've seen on Nissin brake calliper removal and basic maintenance. Having said that, just know that your bike brakes, like your car brakes, will tell you when they need to be replaced. Never hurts to replace them early, but don't panic and stop riding because your pads look thin. They'll squeal like a pig to tell you when it's really time to replace them.

I love that you mentioned the trick of using a screw driver and the old pads to push back the pistons! I've never seen this mentioned in other videos, but this is really a good trick, and I use it personally.

I changed the brake pads on my 2013 Honda CB1000R today, both front and rear - and after coming back home I opened youtube and saw this video on my homepage. It's a good guide to go back to, even for experienced DIYers like me. Good one, team!

Perfect timing! I just ordered some new front pads for my bike. Thanks for making this vid 👊🏽

I always like to tape an empty beer or soda can in-between the brake lever and the handle bar to make certain that I don't inadvertently squeeze the brake lever while servicing the front brake. Also, it is very important to replace the brake fluid every two years (minimum) regardless of mileage on the bike. This will prevent expensive repairs due to corrosion in the brake system. Thanks for another great SM video!

I must say this video has posted right when my rear brake pads have worn out! Talk about perfect timing aha!

Very thorough indeed. I always learn a few things, thanks for the upload!

You know? I am not very mechanically inclined. I can do some work and install stuff, but this type of work is a bit above my pay grade. I am glad this content exist with the very specific experienced tips Ari provides. If I ever have to do it, I know where to look for info.

just changed my front pads today, one set was oil soaked from a leaking fork, fixed that as well in the fall, i’m gonna replace the rotors and rebuild the calipers and change the fluid again then rebuilt the rear caliper and put new pads on last april when i replaced my tires 😎

Salamun Brother… Jazakallahu khairan… Your demo and explaination solved my dizziness… I”ve screwed by a culprit (fake mechanics)… Need to get whole new set of disc brake set… 👌😌😉

Thanks Ari you are the best! My V-Strom has new pads and drivetrain thanks to you.

Good video and quite comprehensive. However, the hang pin can and will wear out over time. Most manufactures have intervals for pin replacement. If the pin becomes really pitted or if you see a flat spot where the pad rests, change out the pin. They are usually under $10 so it’s cheap insurance. Also, no mention on how corrosive brake fluid is. When you push the pistons back into the caliper it pushes fluid into the res which can cause splash. I will take the lid and the rubber seal off the res and then just place it back on top. This will allow air to escape the res as the fluid fills it back up. It’s also a good idea to wrap shop rags around the res just in case. If you do get brake fluid on anything especially painted surfaces. Clean it immediately. Most brake fluids will eat paint.

My Vstrom doesn't even have 2000 miles on it, but I still like watching these videos. Love this series!

Some great tips in there, thanks for posting.

Probably need to do my car 250r soon. Want to get a faster bike but can't afford it. Thanks for the info and demonstration. This channel helps me a lot

Ari, simply put, I Love You Man,,, thank you for so so many valuable skills. I've been a fan of yours for ?? over 30 years ??? bro,,,

Thank you for the great video always a pleasure to watch even tho its straight foward. Thanks😁

Awesome informative vid sir! Guys like u producing vids like these save guys like me $$$. Thanx again!

Don't forget to put the cap back on the reservoir before that test ride! Good video.

I love this series, please keep going

I always dreaded touching anything on my bike and now i am getting more confident and found out it's not as difficult as i thought it will be. Thank you so much man.

Another excellent and informative Shop Manual. Unfortunately, we have very different definitions of "easy" -- as I'm pretty inept mechanically.

I have learned alot from you, and I look forward to learning more Thak you.

Gr8 vid. I often change brake fluids when changing pads; habit forming. The rotors, every other time. Anyway, ride safe, god bless u.

Great stuff . Keep this stuff up helps alot 😊

Very nice tips!! Greetings from Portugal 😉✌️

I love these videos, please keep making them!

Good informative video as always, good to note that just pushing the pots back in with out cleaning can lead to leaky o-rings. I've looked around and couldn't find rebuild kits. Thanks for the Kershaw code, just placed an order.

Dude your videos are so ducking good man really great channel

Easier than I thought. Very informative 👏

Waiting for more DIY shop manual videos💥❤️

thank you very much for the detailed step by step illustration, liked it a lot!!!

Ive learned so much, and saved alot of money, from watching your videos, theyre really well made. Thanks so much for all your work and knowledge!

Too hard. I'll just stop using my brakes all together

Good stuff as always. Thanks y’all

As always another great video ❤️🙏

Plenty of great little tips

Nice tips! Thanks for the video.

It is worth noting that on some ABS-equipped bikes you may need to push the pistons on the calliper back by opening the bleed-bolt on the calliper, and not up the brake system, since the ABS pump will work as a one-way valve... Ask me how I know =P... Reading the manual gave me the answer for that one =)

i agree with not needing to use disc break quiet grease etc. If you got a clean caliper you get no squeaks.

Please do a video on things like fluids, oils and grease that goes beyond engine oil and radiator fluid, what should be used where. E.g., if I'm to oil a clutch cable...what oil should I use? What grease should I use on what bolts? Where should I be using loctite?

I did put goop on the back of my rear brake pad and it eliminated the horrible noise when i drag rear brake in parking lots. I don’t care if it gets dirty, that sound was such a nuisance! lol

Be careful with all the fasteners of course. But those reservoir screws are NOT going to be a Phillips. They are likely going to be JIS, which look very similar. You'll be surprised at the difference when you actually fit the JIS bit vs the Phillips bit in that screw. The JIS screws are identified with a little dot on the head of the screw. Hopefully this helps!

You should put thread locker on the calipers mounting bolts

I’ve doing the lazy method all this time, just because I did not know better… thanks for the video.

Great instructional video, well done and thanks for sharing!! Amateur question pls. Is it ok to use the soapy water on the pistons, will it not remove the grease and cause more corrosion? Thanks for the reply. 👍

I literally just searched for the Motorcycle Mag video this week. What timing.

amazing vid thanks ari

My understanding of seating new brake pads begins with installing the new brake pads into the caliper and screwing the caliper bolts in leaving approximately 2-3mm of space so the bolt head is not touching the caliper. Once you are ready to torque the caliper down, to gently squeeze and hold the brake lever, seating the caliper, pistons, and rotor disc. Then torque down the bolts so they are all in harmony. Is this true or no?

Most excellent and thorough👍

Nice video. I like how you showed your JIS screwdriver (made by Vessel, good brand! ) the screws for the brake reservoir are not Philips! So many of those screws get knackered by guys using Philips.

Good video. Videos from DelBoy’s Garage and Stuart Fillingham are also good for cross reference. Given that brakes are the most important component of any moving vehicle, I would note a few suggestions: First, the reservoir cap should not be opened. Brake fluid is highly homophilic and hygroscopic and will suck moisture, potentially compromising the entire system. Second, don’t bleed fluid. Assuming that the fluid was set properly, bleeding any amount will lessen braking performance. If the pistons are too hard to push back, get a cheap brake kit designed to do this. Third, might as well flush the fluid. Yes, every two years is the norm but why not at the same time - it’s the most critical aspect of the system. Last, if using Simple Green, get the purple version to avoid corroding alloys/aluminum and rinse thoroughly.

You forgot to check for air bubbles in the circuit, wich are pretty common to appear after you push the pistons back in place. I'd say bleeding the circuit is a must after every pad change.

I swear y’all release these the day after I think I should do something. So helpful. And just a little creepy.

Another great video. Have a great day everyone.

Try a C Clamp for pushing calipers back, This is fine for non ABS breaks, If ABS do not push fluid back up into system, open blead screw prior to pushing calipers back so old fluid is bled of. Close bleed screw refill reservoir with fresh fluid. then pump brake, then use procedure to bleed brakes. Fluid is cheep.

Ari is the best mechanic to have ever lived.

great video

Jebus, Zach is fucking RIPPED these days! Oh, and yeah, this is one of the best brake tutorials out there.

great video!!

Hey, thanks for this video. Can I please ask, what clear screen is that attached to the stock white one? I need one of these for my 250XR. Many thanks, Nathan.

I just swapped yesterday to sintered pads 😎

Super easy job on most bikes.

Don’t forget to put the lid back on your fluid reservoir. 😉

hello! thanks for your nice words. For my fzs 153cc (fazer byson) carburetor bike, company manual book recommended 20w50 grade engine oil, but I used 10w40 due to unavailability of reputed company's oil like mobil1, motul, liquimoly etc. . Will it be a problem? What should I do? My odo is nearly 60000 KM. I live in a tropical monsoon-type climate, with a hot and rainy summer and a dry winter.

unreal,i replaced my front gsxr ones this morning!!!!!!!!

Ari, Great video, a couple of things to note. Antilock brake systems don't like dirty fluid, open the bleeder when you compress the pistons back into the caliper. Cleaners like Simple Green are mildly corrosive to aluminum alloy parts, be sure to rinse them with fresh water when you're done.

i was very sad when the mc garage guy left but ive found him again!

OMG never thought about your very clever way to mesure disc thickness, i feel dumb now having bought a micrometer for this purpose....

i can never find out why but on all dirt bikes and atvs I've had the brake material shears off the backing plate . non of my road bikes though. most people hit the trails carrying spare brake leavers. i carry spare brake pads

You can use a C clamp to crush in those pistons. Did you mention to put back brake cap???

Great video very informative thanks! What do you do of you get it all back together but the new pads squeak or squeal while stopping?

So once you've replaced the pads and pumped the brakes. How much should new pads rub? I'm always confused as to how much rubbing is too much.

Enter to win a free Kershaw pocket knife here: a.pgtb.me/W6wfPG Learn more about your bike’s brakes from Ari’s Common Tread article! rvz.la/3JTJltt

I subscribed, thanks

Blessings sir. 🙌🏻❤️

Yo I did the same thing but the caliper are kinda tight to the disc is makes noise and feels hot even though I don't apply breaks at ll

Can u make a video on shelf life of engine oils

Hey Ari, can I use brake cleaner to spray the caliper and brush it?

How does one determine whether his pads need replacing, or his brake fluid/line need attention? My rear braking on my 2018 Grom feels "uneven"... Please advise, thanks

Good video. Just note that at 3:25 you have the caliper hanging off the brake hose. Not a good idea, better to secure it with a rag or thin rope as not to put stress on the hose.

also a good time to replace and bleed the fluid. It's quick and easy and you're already messing with the brakes anyway.

When should one change the pads approximately?

had to return mine. website has the wrong ones listed for the front brakes.

Chrisfix used Copper Anti Seize for the sliding area

Great video, my bike got ~1500km but its front brakes are still squeaking. I can now take the break pad thingy out for a scrub.

Can i use petroleum to vlean the brake body instead of water because my mechanic neighbour yses pretoleum but idk if it is safe

I heard that a medium threadlocker (locklite blue) is applied on caliper mounting bolts. Is that a necessary step ?

Is dishwashing liquid mixed with water okay for cleaning?

I pressed my front brake while there wasn't an brakecirkel, I managed to get it fully open again and changed the oil and aired it out, buth the front brake wont close anymore so is there like a way to fix that??

Always find your tutorials very helpful. Thank you👍

How about going into bleeding the brakes too? That might be a good Shop Manual. More intimidating than it is difficult.

Those arms tho. Legend says when he needs to stop he just grabs the earth.

But What about the rear onE ? Im stuck and the one I needed to replace is not done yet :(