Awesome tutorial! Right to the point. No waiting on each screen!

Bro. You are my new best friend for the day. You went straight to the point and easy setup. Thank you. Mines work perfectly.

Your tutorial was very easy to follow and accurate. Thank you!

Great walk through.. All life should be this easy! Thanks!

thank you very much, installed mine in like 10 min because of your vid, I opted to just get 3m double sided tape instead of screws and it works awesomely. Thanks again Merry Christmasss

Great video! I like how you explained things in a manner where an “all thumbs” kinda guy like me could understand! Thank you!

Perfect thank you for your time. Your directions are straight to the point.

Been thinking about getting this but wasn't quite sure how it all worked. This looks super easy and now I think I'll go ahead with the purchase. Great tutorial!

Just got one ready to install ! Thanks for sharing info very helpful ! 👍

Thank you sir, set mine up right along with you and worked perfectly 🤜🏽🤛🏼

Great video tutorial. Thanks for doing this. I am going to get one of this since my garage opener is a Lift Master also.

Two suggestions/corrections: 1) make sure you have a good Wi-Fi signal at that location before installing the mount; 2) use the long screws into the drywall anchors - the short screws are for mounting the door sensor to the garage door and are too short to expand the anchor behind the drywall to secure it.

Sir, I just set up chamberlain hub with your Video. Every step you showed perfect. I just got set up smooth. Thanks

This is awesome! Thanks for the video, I'm going to buy one tomorrow.

Very concise and to the point, like VB said. I hear Chamberlain is hiring for video tutor stars. Just saying!

I usually don't comment on DIY videos but you did such a great job explaining from beginning to end. I had to say thank you. 👍👍

If I have an older but still working garage motor without a learn button (old screw/wires/flipswitch code kind) - is there a wire i can hook to hub directly ?

This video was a huge success thank you.

Can you still use the remote openers that come with garage opener after you pair and set up the hub?

How does the sensor know if the door is open or closed or half way or anything? How is the sensor calibration to what? It’s it any movement it registers and considers that a valid open or close command

Excellent tutorial Ceasar. Now I will purchase!

So there are 3 buttons on the control hub. Can I set it up to where I can push the button and open/close the door?

Awesome tutorial and great recommendation! I was worried that because my garage was on the older side I wouldn’t be able to find an easy way to connect my garage door to my smartphone, but this proved me wrong! As soon I saw this video, I ordered it with same day shipping from Amazon. Install was very easy and I like that the app also walks you through installation- step by step. Could not recommend this more, thank you!!

I haven't seen this anywhere. Perhaps you can help. Can you setup and operate the garage door without a myq sensor? I want to use myq hub with a ramset gate opener that closes automatically after 10 seconds and works with a typical multicode control.

Best part of this, is DING DONG!

I just got mine today, thanks allot for ur help, great video

I just installed mine recently. I wish the programming was as easy as the demo here! It took me over 3 hours from unboxing to operation! Lots of glitches encountered. Had to find phone # to Chamberlain and call tech support because my app kept rejecting my wifi password! He had me do a back door setup to get the password to work. He admitted there must be a bug in the app preventing me from entering my wifi password! THEN, try to pair the opener to the hub! OMG! Almost gave up because the app kept saying my machine was not compatible and I could only use it to find out if my door was opened or closed! Not having that! My Genie has a program button, but it's black. The LED indicator lights are buried deep inside the machine, so nothing like the instructions say. + the button has to be HELD down for over 2 seconds! NOT a doorbell press. AND, I had to have a hand held car remote on top of that! Had to go through setup over and over and over again until, like an hour later...Finally paired! Now, it sorta works, the the built-in LED light does NOT flash when I hit close on the app! What a mess! So, beware, it is a bear.

Yur vdo is awesome. Need 2 install a fence w/ garage opener & yur vdo is just perfect. EZ peazy 2 installed. Thx 4 sharing on Utube.

Awesome I'm buying one right now! Thank you

Question: Looked at the manual and it is unclear, do the buttons on the front of the Hub marked for Door 1 and Door 2 function as an opener?

Do the photo sensors have to be working for this to work?

Great job. I appreciate the help.

Terrific job on this video. Thanks so much.

can the hub be placed anywhere in the garage? the app/quick start looks to be right above the garage motor

great video ...i have 2 doors and was told i can program both doors to one module. Assuming this is correct, i am guessing rinse and repeat for both doors. Can anyone confirm?

Quick question. What does the hub do? Why would I get one. I'm asking because I want to know if I really need it or not. Thanks!

Some people complain. This is a free video. You don’t like. Skip. I like yours

So I just learned that if my opener has the MyQ logo on it, all I need is the app & dont have to buy the "MyQ garage door opener by Chamberlain. ". Would this be correct?

You can also link to Ring with that setup and control and monitor with your Ring App

Great video and made me purchase the MyQ Device. Hope that my install process is just as smooth! Thanks

Right at the last you mentioned LTE or 5G connection but I did not understand how this works with WiFi? Also does the app warn about when to change battery?

How frequently have you had to change out batteries? Thanks

Hi, do i need a hub or garage door opener even if my opener has myq logo??

Thank you fast and easy❤❤❤❤

Nice job thank you

How do you get rid of the alarm when closing the garage door?

Thank you dude!

Very nice video & clear I did mine also Thank you

I'm feeling like it is working via Bluetooth so, although I can know if the garage door was left open when I'm away from home, I'm thinking I cannot close it if I am away. Is that correct?

Can it be set up with Google Assistant/Google Home where I don't have to open the app but instead say, "Hey Google, Open the garage door". Or, "Hey Google, close the garage door".

thank you!

Does this work with Lift master made by Chamberlain ?

Good stuff.

Thank you

By installing that will that unprogram my 2 garage door clickers?

What a great tutorial! Can I pair one MyQ with two garage doors?

What are the buttons for on the MyQ hub?

If you have dedicated garage door openers. Do they have to be reprogrammed at the same time you are programming the app? Or do they remain unaffected?

My security system requires I use 2.4Ghz, will this also work ?

Does the hub have to be in the garage?

Can you open door partially with myQ ?

Great video.. would give tip if you’ve gone though this set up and opening and closing is inconsistent.. especially closes, but often won’t open you could be getting interference from LED or halogen lights in garage.. mentioned in support troubleshooting guide that they can give off radio interference. I needed to remove all LED bulbs.. reset MYQ hub and redo setup.. if just remove bulbs, it will still have faulty code for garage door and still be spotty. After doing this it works flawlessly every time!

Thanks for the video. Were you able to mount the hub at least the 4 feet away from metal specified in instructions? It seems unreasonable to expect this since most folks will plug it into the ceiling receptacle near both the motor, tracks, and hardware associated with the door.

Question. Does the hub need to be on the ceiling? I saw a lot of people do that but you just mentioned "6ft above the ground". So wall works as well?

Can you use this on any garage opener?

Hello, I have an international router and my garage is around 100 feet from my home. Will I be able to use this device? In the garage, there is no internet signal. Or am I just being stupid and don't get how this works?

the short screws are for the sensor and the long screws are for drywall.

What is the hub and the sensor for?

do you have to conect to the garage opener?

did you connect to a 2.5 or 5 Ghz? with the app..

Tried pairing last night to my liftmaster motor. Couldn’t get it to pair. Tired all the learning button colors on the app and failed. Will be retuning this item today.

So when you pair the myQ to garage opener, my homelink and remote we used prior to myQ, stopped working. Anyone else run into this? Is there a solution?

Do you really need to mount the hub? Is it necessary?

Does the hub needs to be facing the sensor? Same height level, facing each other without obstructions. Or, can have be installed on side wall?

Great video.Does the senser need battery?

Great job man.

Can I connect this to Google home app?

i notice that if you closed your garage door it will have sensor sound - so how can you turn it off?

Love the old version

can I mount hub on ceiling

Does adding the MyQ system override the factory provided keypad, or remotes?

After it is installed, how are other family members able to open and close the door with their phones?

I have 2 doors. Can the app support 2?

Does this work with Alexa or Google Assistant?

Can I pair a Ryobi?

Very informative. Velcro stick-ons in the garage? Come on MyQ....

Hi, great video! What size and type of screws and anchor do you need?

I have question. In case wifi is down or battery inside of sensor is dead, will the door still open by using original remote control? Or once everything get paired, you can only open garage door with myQ app?

Does it work with Genie?

Does the sensor have to be on the right or left of the garage door? can it be in the middle?

I thought you had to register the sensor and the hub by scanning the barcode or enter manually? I had to do with mines..

Interesting, I just put a chamberlain in last night. It says it is blue tooth and wifi, and tells me to download the MyQ, buuuuttt...I did not get that device you just installed. Now I need to read more!!!

Ding dong. Ding dong. Hillarious.

Is there a paid subscription required and does it make a alert beeping noise when closing?

Mine will start to open maybe a couple inches and stop. Same with trying to close the door

How many users can control from the app ? In their own Smartphones.

Mine is craftman and doesn't have any bottom to push 😢 where can I look to pair it?

Can you still use the garage door opener in conjunction with the app?

My app (MyQ) keeps asking me to press the learn button and wait for a beep. The beep never happens and connection fails. You must be using an older version of the app. Installation is different now.

Hmmm, interestingly enough, it's not the same steps to reconnect if you ever reprogram your garage door opener. At the 00:06:08 mark of your video, these steps vary if the device has been removed from the garage door opener's old program setting. I am going to see if it is possible to do a factory reset on the Q Hub, uninstall the app from the iPhone too, and treat this as if it was a brand new instalation. Let's see if this will allow me to reconnect successfully back onto my WiFi network. Thanks for your video, it's better than than what the Q Hub folks have up on their troubleshooting videos, LOL.