You can order Fender Flares Here www.vividracing.com/index.php?keywords=Pro+comp+fender+flare+toyota+tundra

Soap added to the water will make a absolutely slick finish. Glass glazing we use hundreds of tube of silicone. I talked about this on a radio show for home owners trying to caulk their glass and tile showers.

Nice. I'm a painter and if you want it to look its best . Usually takes two coats for a perfect finish (going both directions )

Great video man! Way better than the alternative of paying for weatherstripping and not guaranteeing the perfect fit! Keep it up!

Just did that to my Silverado! Thanks for the video, came out pretty sweet. Taking your time with the tape is key to get clean lines. The rest was easy! Thanks again 🤙🏽

Wow life saver. I imported the silicone strips for £200 plus .and because I change the colour of my car alot, alternative was need. Great job luv youtube 😎 ps brilliant truck keep on posting .

Never occurred to me to caulk between the gaskets and paint, but it makes perfect sense (I use caulk in my job all the time- construction). Clear GE Silicone is the way to go. Use regular white masking tape on the gasket (to bullseye it accurately) and light or dark tape (to contrast with the particular paint color of your truck. I put flares on fenders that had uneven surfaces from being sideswiped. Using clear kind of fools the eye into looking at the flares and not the bent up sheet metal. Not showroom perfect- but I wasn't about to buy a whole new bed. Buy a caulking gun (10-20 bucks) to inject deep into the gap, allowing more to slightly run up and onto the tape. I use a rounded stainless tool for scraping away the excess, but an old butter knife will do. Have an old newspaper cut into squares for wiping off the knife every couple of inches as you're tooling. Pull the tape off IMMEDIATELY after or you'll have a mess doing it later. Wear disposable gloves and toss em after each flare. Tip #101: start with the part of the truck you NEVER look at- the right rear. If it comes out a little funky- so what. You learned what NOT to do on the next one.

Nice job, really gives a clean look. Wish I could get flares like that for my Ram.

Wish I thought of this when I put my bushwackers in years ago. Payed for the best fender flares because they were supposed to not allow for scratching the finish. But the dirt and sand got in there and left rings so I have to leave the flares on.

Man...that's the way to put them on. That rubber trim is garbage compared to this. Thank you for posting this video, looks super simple.

since this video was made have you ever gone back to see how it has come out or see how it has lasted weather the silicon has separated from the fender or not or how much it has moved? also being that u didnt use the seal that came with the fender flares do u worry about the paint being rubbed through due to seal being replaced?

Sikaflex-221, Black, Multi-Purpose Sealant/Adhesive, Polyurethane Fast Curing Sealant, Works the best

You can also caulk the silicone line, then Wrap over the lines with paint code matching metallic vinyl for a seemless look.

This kind of fender flares is awesome

What’s your “clean-up” process that you mentioned at the end?

Clean build

I like how u said I’m rwbing my tundra lol good video bud thanks for upload

Does the silicone replace the rubber stick on stuff that comes with the flares? I have bushwackers, but I took them off and found the rubber has left a ring of scratches around each wheel. I guess the non stop dust of the gravel ranch roads did it. Would this solve the issue? Thanks!

Damn dude this truck looks very nice.

That’s one sweet looking truck!

So these are stock fender flares or add on. I have stock on my 4Runner and there is gaps between them and the body and wonder if this would clean up the look of them.

What are you going to do if you have to take the flare off?

Love ur guys products btw ! I wish you'd shown n explained the tape process

This is a game changer

CLEAN BROTHER.

I have a 2014 tundra will I have to do anything other than use manufacturers holes when putting flares on hopefully no cutting?

Thank you, for the info. I think I'll go with the pro comp, as you seem be a Pro in modifications, I'm going to take my Truck to a body shop for installation of the Pro Comp Flares, as it is out of my skill level, it comes with instructions right, how long hours to install ?

That’s the sexiest tundra I have ever seen!!

Love the look, but from one Tundra owner to another, If you ever have to change headlight bulbs you need to take the grill and and winglets off, which also means you would have to take the fender flares off and ruin the silicone

When you applied the tape on the truck and flares, I couldn’t see in the video but was there a fine line gap between the tape that allowed you to put the silicone on the truck between the flare and truck itself or did you literally apply the silicone on the actual tape at truck and flare interface and by wetting the silicone, the tape just simply pulled out from underneath and the adheres to the truck? Thanks!

What brand of silicone did you apply?

So cool. Where u find those fender flares they r so nice

As i am doing my research PPF film will break down over time due to wear and weather conditions so I'm not going that route but I'm considering doing your method instead..... questions do you use the rubber seal that comes with most flares or you don't use the seal at all in your method , do you add more of the sealant to push more into the flares so it covers most of the flare lip that sits on the fenders, what black sealant did you use , how well is it holding up ?

Why do we do this? I don’t get it. Why not get a string of LED lights and run them along the fenders. Just my thoughts.

Hey Nice tutorial. Do you strictly recommend a caulking gun? I ran to the store to try and find a black sealant but they didn’t have any, so i settled on the smaller toothepaste looking ones. (didnt know the name lol)

I needed this👍🏻

im very late to this but im planning on glueing my fender flares with windshield adhesive for better durability and was wondering if i could use the same adhesive to seal in the edges afterwards like you did? or am i better off using silicone?

What did you use to mount the widebody kit and what would your recommend to create the water tight seal

😲 😱 omg amazing video 📹 that truck looks awesome but you need more beefy wheels

not to be a stick-in-the-mud,but I hope you never have to change a headlight, because that small quarter panel under the headlight lense has to come off ( lame design)

Great idea brother.. hows it been holding up? Any vibration or bumps separated the silicon anywer?

Are you doing this to avoid rust? My worry about fender flares is it rusting out the fenders by holding in moisture over many years

very nice truck and the color is amazing do you have a diy installing video for the fender? how do you mount the fender is there any drilling to the fender? and what kind of grill insert is that for the hood grill?

If I have a minor gap between my fender flare and the rubber seal, do you think this silicone trick will do the job to fill in that void or should I try to readjust my fender flare somehow?

Hi one question. What do you use to remove the silicone stuffs ? if one day need to remove

does it will damage the car body paint if i want to remove the silicone one day?

How did you get the line so thin and perfect ? Could you tape over the seam, then slit it with an exacto knife ? Would the silicone slip between the tape and seat in the gap?

Show how you laid down the tape. It looks like the silicone is just sitting on top of the fender flare seam and not getting between the two plastic surfaces to act as a gasket. My fender flares are loose and squeaky from off-roading so I'd be doing it for function and not just for looks.

Great video,what is the colour of that truck

Do you have any videos on the install not the end result?

Curious…I just installed flares on my truck and want to run a bead of silicon but just hesitant given white truck, white flares and silicon discoloring over time or given weather conditions, cracking. Any thoughts??

Trying to figure out your taping the fender flares up to vehicle and also what do u use to clean up any over do of the silicone sealant.

Are those the pro comp fenders? If so, how did you find ones without the bolts being shown?

I like that wide body kit I wonder if they have for 2020 Tacoma wide kit ?

Does the silicon damage the paint?

Any videos in how to do the actual installation ? I bought them and i cant find guide in how to

That truck is sicccc are those te37 wheels??

Do you recommend black silicone to repair a broken off flare? The only way to fix this would be to glue or purchase another flare which I can't afford at the moment. But my jeep looks tacky with one flare missing. Please help!

Does it matter what type of silicone you use?

Thanks for the tips

So this is how you stop scratching from fender flares? I didn’t do this and now my RC flares on my silverado have scratched a little around gasket into the paint from dirt build up :(

Can you please tell me how long it took to install the Pro Comp Fender Flares, Please.

Sweet Rig...Does the truck have a long travel kit?

You did a pretty good job man. Where can i get those fender flares i just can't find them

My question is how do you know if the flares edge isn't rubbing the paint ?

Dude, I need it for my 2012 model

Tell me about the flares install is there any cutting or mods to install, I'm also looking at Dura Flex Fender Flares any inf on them.

Debating on fender flares on my new truck..They look badass..but I hear so much about them rubbing or something and damaging paint

What specs of wheels? what size of tyres? what rims parameters? thanks

Do you have some fenders like this but for rams?

So in theory it’ll protect against rain?

Do you leave the rubber seal and silcone over it, I think would be best how do you do.

What silicone did you use? Will it be strong enough to hold up the fender without any bolts?

What kind/type of black Silicone are you using?

Do you guys carry for Nissan titans??

Is that a 4 inch lift kit on that sweet truck 👍🏻

And does it peel right off when flares are removed ?

by letting it dry before you pulled the tape you eliminated the chance of a perfect job...Tape,,,silicone,,,wet finger,,press in silicone,,pull tape carefully,,wet finger,,lightley run finger over silicone,,,BINGO

Do you have spacer wheels?

I still can't find!!! 2019 tundra fenders.

is there a fit for those fenders for a 2019 tundra? I've looked all over your website and I cannot find it. thanks

What type of silicone please ?

Do you recommend a cold air intake for this truck?

What silicone did you use or did I miss that?

DAP???

What kind of silicone did you use?

Found this and after 6 years the corner by the mirror sticks out so much the 3m tape didn’t hold at all I’m gonna in weld it or rivot it or something I hate how much it has curled.

What flares fender is that?

How much are the fenders

Who sells those fender flares i thought it was pro comp but i vant find them

Nice truck dude,please what's name of your fender flares

Where did you buy the fenders flares

What are the brand and where can I buy those flares. I have bushwhackers poker style and I like those better

Clean

How do you remove the old silicone

Where can i get those fender llares

Where can I get these Fender Flares.

Which silicone do I need ?

How did the silicone hold up? I’m in the process of installing these on my truck now and came across your video.

What brand silicone did you use