Lol also helps with a new machine where everything comes apart smoothly lol

Thanks brother I appreciate it!!! I will definitely try to make more mods videos!

It was so nice to work on such a clean bike!!!

@Yusuf Jake your account has been reported for spam

Thanks Jen I appreciate it!!!

The airbox is just the two clamps, the crankcase breather hose, and the O2 sensor clip and two push pins clips. I'm doing another 2020 tomorrow, I will try to remember to do a video of the teardown

I definitely use dielectric grease for all the plugs... but I prefer to seal up the airbox with the ultra black. Sure...it's a bit of work to take the lid off... but it's worth it. I appreciate the tip tho sir!

Thanks brother I appreciate it!!!

Sorry I just saw this! I just dielectric grease every electrical connection on the bike. I've not really had any electric issues and I take my bikes between 6-7 foot deep

Yessir and yessir!

I was told and I read the k&N filter let’s in more dirt then the stock one. I don’t want to add a filter that isn’t as good as the factory. I also read a mechanic that works on these rebuilding them said the ones that have k&N filters other then the stock the throttle body is always has more dirt and the engines need rebuilding sooner. Can you give me your opinion on this matter?

4 foot of 1/2" inside diameter heater hose from auro parts store

Yessir!!!

I just bought the 2021 and she's a beaut!!! Definitely gotta give it a snorkel though bc it does not like water at all

Niiice!!!

👍💪🤝

Yessir!!!

I always start with a new filter, and if I need to change it I pull the airbox back out and cut the lid loose.

Is there a rubber boots on the vertical snorkel standpipe? If so, switch it out with a pressure coupling and make sure it hubs at both ends of the coupling

@@SomeDamnfoolsAtv ok thanks for the help I will be swapping out my rubber boot

I build all my snorkels next to the frame and use pvc pressure fittings to keep them from wobbling around. Behind the plastics out of sight I zip tie the pipe to the frame for extra support from it wobbling...I can't stand a wobbly snorkel

Coupling or 45°.... depending on how you are routing it

What did you use in this video? Hoping to do same setup but around shock to center snorkel

Take it apart and put silicone in it

I prefer inch and a half. That's what I run on most every Honda I do

Permatex ultra black gasket maker

I thought I showed it in the video

Some Damnfools Atv you might have not sure it kept freezing but thanks a lot I’m going to snorkel my 420 tommorow just needed to know

Where you get it from

Absolutely!!! Just let me know if I can help!

Some Damnfools Atv thank you I will let you know how it goes

So I tried. It got pretty far but gen my dad decided to take it apart and it never got put back together. If we could somehow work on you snorkeling it and sorta putting it back together. I could pay you

Probably be a good idea to get the kit... and save yourself the markup. Or if you are near NC I can do it for you

If you get the dealership to do it, a lot of the time you can keep your factory warranty. I had my dealership install a worrier riser kit on my 2020 rubicon at the same time they did the first service and valve adjustment. They didn’t charge me labor since they already had the bike apart. Just payed for the service and the snorkel.

Wallace nc

Some Damnfools Atv do you know of anybody in Florida that can do it

Hardware store or Lowe's/ home Depot

3' above the racks

where can i find someone in my area to do mine??????

Put up a post on Facebook in your area on some of the ATV groups.

I recommend either changing the boot or the whole axle. I hate dealing with the boots. Before I will rebuild an axle I will buy a new one. That's just me though.

Takes me about 15 minutes. Depending on a Polaris piece of shit

Yessir unless the dealer does it then it leaks and they void it anyway. Let someone experienced do it and have no problems

1/4 inside diameter and 3/16 inside diameter

@@SomeDamnfoolsAtv thanks and i was having some trouble hearing what kind of pvc sizes I need to get from home depot

I run inch and a half

@@SomeDamnfoolsAtv thx buddy

Looks like regular PVC from any hardware store

14/28 no lift

@@SomeDamnfoolsAtv thanks man looks good !!

Nc

KevWitDaMc I have same question

You guys figure this out

3/16 i.d. and 1/4 i.d.

Yessir I believe so.

Some Damnfools Atv you got a list of the things I need wrote up?

Creates a air pocket in the exhaust in case it dies underwater you can start it back up

Some Damnfools Atv wow super smart idea never thought of that and great video as well 🤙

Some Damnfools Atv will it idle underwater with the 90 degree exhaust tip

I make them all myself.

I do. Reason being...if the airbox leaks and you are unaware, you can do detrimental damage to everything hooked to the vents ... just my personal opinion

Some Damnfools Atv yeah that makes sense. Was just worried about if I flipped it if water would get into all the vents and it be worse

I used a short piece of 1-1/2 pipe and cut a short section off the factory plastic snorkel and sealed it up good

@@SomeDamnfoolsAtv thank ya

Somedamnfoolsatv on Instagram, or Timothy Russell on Facebook

Save the factory piece that comes out of the airbox

No absolutely not

Thanks

I thought they had a rubber gasket

Mine was sealed air tight from the factory 2017 model. No silicone and will suck the whole air box in. I was told not to silicone a air box on a fuel injected bike mine does fine without silicone

@@walteringram721 same with my 2020 ive had it over the airbox factoey snorkel never touched doesn't leak a drop

The green transition glue

@@SomeDamnfoolsAtv isn’t the glue you used in the video black?

@@gavin8832possible but I recommend the green transition glue for abs to pvc. I've yet to have any issues with the black...but get the green if available

@@SomeDamnfoolsAtv ok thanks I’ve looked everywhere but haven’t really found any information. People only seem to use abs pipe with pvc fittings on snorkels lol.

Abs is way lighter...pvc pressure fittings have twice the glue joint socket space. Makes for better setup than using abs vent and drain fittings...aka dwv fittings

In in NC if you want to bring it to me

No. It's my friends new bike

For aftermarket exhaust... definitely! For a stock bike stock exhaust I recommend try without it and turn idle up a little to try and save a dollar

It costs that much for the materials to do it now due to inflation.

Well marlon e. My shit will idle underwater in 6 foot deep water until the fucking gas runs out... with a new top end on a 2019... so believe that video if you want to. That bike of his already wouldn't idle underwater. He WAS the reason I ran Hondas, but the way he put that video out...kinda blew it for me. Not with a Honda, but rather the guy I used to look to for motivation and advice. Take what you want from my comment, the same goes for his video. But either way, don't come at me with that shit when the proof is in my videos.