How to Solve DSC Power Series Yellow Triangle Troubles

No video

How to Solve DSC Power Series Yellow Triangle Troubles

Рет қаралды 147,461

Күн бұрын

In this video, we will trouble shoot every possible element that may give you this yellow triangle on your DSC Power Series alarm system.
Thank you for watching this video, I hope it will help you to solve your problem.
My goal with this channel is to explain how to do something to solve your problems as quickly as possible.
Make sure to subscribe to find me back next time you look at something on KZfaq, I have a lot of topic on my channel.
Also, do not hesitate to ask questions in the comment, I might give you an answer on another great video like this one.
1. Service Required
----- 1. Low Battery on main pannel
----- 2. Fault on Bell circuit
----- 3. General System Trouble
----- 4. General System Temper
----- 5. Module Supervision
----- 6. RF Jam Detected
----- 7. Low battery on PC5204 or PC5200
----- 8. No Electric Power on PC5204 or PC5200
2. AC Failure (no power on main panel)
3. Telephone line trouble
4. Failure to Communicate
5. Zone Fault
6. Zone Tamper
7. Low Battery on Wireless device
8. Lost of Clock/Date :
Video Solution : • How to Set Time and Da...
Need a new battery for your main panel? : geni.us/DSCbat... (Amazon)
Need a new CR2032 battery for your wireless device? : geni.us/CR2032e (Amazon)
Need a new CR2 for your wireless device? : geni.us/CR2bat (Amazon)
I accept donations :)
geni.us/HowToP...
Many thanks in advance!
It helps me a lot to make new videos.
Filmed with this cameras :
geni.us/PMAnx80
My microphone
For voice over : geni.us/ZoomH5hr (Amazon)
Camera microphone : geni.us/RODEvi... (Amazon)
Clip Mic : geni.us/tasdr10l (Amazon)
Follow that link to have a deeper look to all the gear I use to make my videos : www.pascalmarq...
Also please take a look at my main KZfaq Channel : bit.ly/KZfaqPMA
I use this software to edit my photos : geni.us/LuminarPM
I use Artlist to get awesome royalty free music, get 2 month free on your first subscription here : geni.us/ArtlistPM
I use that service to optimize my affiliate links : geni.us/GeniusRef
As an Amazon Associate I earn from qualifying purchases.

Пікірлер: 187

@alejandrom4347 3 ай бұрын

I was about to call the technician, but I watched your video and thanks to you, I was able to solve it.

@louisrodriguez66 3 ай бұрын

Thank you. Excellent source of information. Reduced my headache and time finding out my issue with the alarm quite dramatically. 👌 👍

@joleneartman4734 3 жыл бұрын

Thanks a ton! You saved me like $75 for a service call to replace a $2 battery! Rock star!!

@HowToPM 3 жыл бұрын

Ahah!! Thank you for your comment Jolene! I'm glad it helped! 😀

@suzieq8379 3 жыл бұрын

which battery did you replace and are there a video explaining how. thanks

@anthonyto1281 Жыл бұрын

How to replace the battery

@assogan 2 жыл бұрын

A really well presented video. Easy to understand. Thanks a lot

@robertrocchio446 10 ай бұрын

Thank you for this video!! Very well presented and very helpful!!

@olgasuarez2129 Жыл бұрын

Thanks for the video! You a great, I like the way you explained everything it was very clear to understand you are a pro. Thanks you so much.

@HowToPM Жыл бұрын

Ahah!! Thank you so much! :)

@jalgabriel Жыл бұрын

Thanks for rescuing this old lady🧓 from insanity trying to rid the yellow triangle #7. Not even the manual tells what to do when no zone # shows up. It's the remote fob battery!! Bless you!!

@HowToPM Жыл бұрын

Ahah you are very welcome! I'm glad it helped! :)

@puthenpeedikayilthomas1309 Жыл бұрын

Thank you very much for the detailed explanation. Very good.

@christianluchetta3106 3 жыл бұрын

Thanks for the video. We had a trouble light last night and it showed “1”, then showed “3” and”6”. I wonder what could have caused the RF jam, cause now there’s no trouble light

@teresaiovino7361 2 жыл бұрын

Fantastic information - thank you so much! :)

@jeanahuynh 25 күн бұрын

When I enter *6, it shows 8. Does that mean I change the time and date? If so I followed your link to do so, but I still how the triangle and it show Open for zone 5.

@EVO3444 12 күн бұрын

What if my screen is dead and there is no activity on any of the buttons. only thing that turns on is the orange triangle and the green check mark?

@feijushi8524 2 жыл бұрын

Thank you, your explanation is very clear and useful. My PK5501 panel shows the triangle and beep, *2-1-4. I contacted the alarm company, they said that is low battery, but it is still there after a new battery installation. what next to do? and before i change and install battery , should i call alarm company first? thank you very much.

@HowToPM 2 жыл бұрын

You don't need to call the alarm company to change the battery. However when you install the new one, you might need to wait few hour for the triangle to go away as the battery need to charge.

@anthonyto1281 Жыл бұрын

How to replace the battery

@tmywu 2 ай бұрын

hey, first off, thanks a ton for this! a couple days ago my main DSC panel started beeping twice every 10 secs or so and i can temporarily disable that by checking the error via *2 and # so what i have is a 1-4 (General System Temper error). i had no idea that the alarm box door being open can attribute to this, but i don't ever remember the door ever being closed. i just closed the door, but i still see the error symbol on the panel, what else can be causing this? thanks

@jalapenogabriel8741 8 ай бұрын

Thanks for trouble 7 but no zone showing. Replaced baterries in key fob👍

@lorenascott1053 Жыл бұрын

Great help ! Thank you

@TheSpiljar Ай бұрын

I have trouble with DSC WT5500-433EU system. On my keypad appears message "Panel Response Not Received". Can you help me to solve this. Thank you

@ssupersayaman9779 Жыл бұрын

Thank so much for that information is gonna be helpful

@brandonstill7229 9 ай бұрын

Thanks for the info.

@SharonBourkepilkington 3 күн бұрын

Hello Having trouble finding a battery

@roundrock123 Жыл бұрын

Oh, thank you so much.

@nadajoey1 2 жыл бұрын

excellent video. i have one question. i still have comm failure (*2=4) despite having tried to remove it. Could it be that the PC1832 keeps trouble errors in memory? if so, what is the best way to reset the panel without losing zone information? thanks

@HowToPM 2 жыл бұрын

It can be something in memory. The best way would be to call your central to be put on test, and then try to call an ambulance on the keypad. If the comunication work, the trouble will vanish.

@nadajoey1 2 жыл бұрын

@@HowToPM I forgot to mention I no longer have central service connected nor a phone line. So I toggled off the communication [380] and also [015] toggled off #7. But the yellow light still stays on.

@HowToPM 2 жыл бұрын

In this case just reboot the alarm. Disconect power and battery for a minute and reconnect it. It should be solved. You will need to set back time and date however. But this video will help you to do it : kzfaq.info/get/bejne/o8ufobWUuZzScZs.html

@Woesco3 11 ай бұрын

I out new batteries in my living room sensor and it still says it’s a zone fault. So right now I’m going to replace the main control battery pack

@jeremyvick2682 11 ай бұрын

Thank you, this was great information. What does it mean if you see a green check mark and triangle, but the display screen is completely blank & nothing shows

@HowToPM 11 ай бұрын

If you aren't able to see anything on the screen at anytime that make me think to a short in the JKT cable.

@Maiaal100 3 жыл бұрын

excellent video man,,, thanks a lot

@toml7775 9 ай бұрын

Also I commend you on a clear and easy to listen to the many DSC alarm troubles. You missed trouble #9 that tells the user to trash the system and replace it with a newer better non-DSC system.

@HowToPM 9 ай бұрын

I would not say that. I have install many DSC system over a long period of time and would say that it's probably the most reliable tech I have ever use. Very very low defective rate. The motherboard is very solid and reliable. It can also resist to short for a long period of time. It's built like a tank. And most if it is built right here in Canada. I also remember that I had a wonderfull tech suport on the phone.

@gameking1916 2 жыл бұрын

You are smart

@HowToPM 2 жыл бұрын

It's just experience but I will take the compliment. Ahah! Thank you. 😉

@narc508ryals9 2 жыл бұрын

Any suggestions on the light coming on and it dying before I could check it

@piperlucille 2 жыл бұрын

Thank for you this video! The yellow triangle came on and it was the phone line. My phone company came out and fixed the phone but the yellow triangle is still showing. Any thoughts??

@HowToPM 2 жыл бұрын

It was probably a failed comunication. It will be fixed by it's own on the next comunication. It probabably do an auto test every days or week. You could also call an ambulance but advise the central that you will do that test.

@fatz445 3 жыл бұрын

great informational video. i am not getting alerts on my app.{ arm disarm etc}. what did i do wrong

@HowToPM 3 жыл бұрын

I don't know wich app you are using. DSC don't have app. There is some third party that can connect to it but not DSC directly.

@evonpruitt8873 3 жыл бұрын

Excellent

@mickbrown815 Жыл бұрын

I’m back again a year later. So mine shows 1 and the battery shows 13.58v on the meter, written on the battery it says that rating is a constant voltage standby mode. So does that mean I need a new battery? The constant rating charge for cycle use shows it should be 14.4-15v

@suzieq8379 3 жыл бұрын

Mine will periodically both lights go out for a few seconds then come back on such as yesterday I noticed while sitting in kitchen where the keypad is about every 3 hours it would go off for about 5 or 6 secs then back on.. Is it necessary to have the phone plugged in, cause I leave mine unplugged unless the alarm sounds then I plug it up.. My security service is out of Tennessee and my phone line is in Kentucky which is where I live?

@naisonmncube7618 20 күн бұрын

hi how do i bypass a zone on this keypad

@HowToPM 19 күн бұрын

kzfaq.info/get/bejne/d7J2ZpxpprWok5s.html

@vinosubramoney2519 2 күн бұрын

I am.told that power series has been discontinued. So u can't get ws4939 . Please advise

@HowToPM 18 сағат бұрын

Yes it has been discontinued. You may still find so piece on marketplace like ebay.

@pkwcs 2 жыл бұрын

Thanks for the video. I have a wireless sensor (smoke detector) with low battery. But i do not need that sensor and zone anymore. What are my best options to remove the smoke detector from the system? My panel is DSC RFK5501

@HowToPM 2 жыл бұрын

*8, installer code, section 201 for zone 1 to 8 or 202 for zone 9 to 16. Then disable the zone. I will eventually do a video about all this.

@detrence 2 ай бұрын

What could be the causes of both alarm keypads no lights or display?

@HowToPM 2 ай бұрын

Looks light a short in the system somewhere. Positive touching negative.

@jerrywilson1967 Жыл бұрын

I have a DSC 1864 alarm panel, two of them, and the yellow triangle won't go off. No faults, no problems, the panel says everything is good, but the yellow triangle won't go off. I have a yellow triangle and a green check mark. How can I get it to go off......none of the fixes in these videos will make it go away!

@HowToPM Жыл бұрын

I'm confuse. When there is a triangle, *2 should display the issue.

@jerrywilson1967 Жыл бұрын

@@HowToPM It does not. The yellow triangle is lit, but *2 yields no faults.....no low batteries, no tampers, no zone faults, I don't know what to do to make the yellow triangle go away. It's so strange.

@thescibsters2049 7 ай бұрын

Did you ever figure it out? I have an led screen but same model everything else. My yellow triangle wouldn’t go off. I had no issues either. I have no idea what I did, after watching a couple videos and banging the pound sign a bunch but it finally went off. Then the company we’re connected to called saying I asked for a medical emergency. 🤷🏻‍♂️ Did you find a better way to clear the system trouble light?

@vingiang7159 2 жыл бұрын

The faulty design is Yellow Triangle Troubles, when showing up, my clients is keep pressing the triangle button, causing the Ambulance come to the front door. it happen very often

@HowToPM 2 жыл бұрын

😂 I never had a client who did that. But I make sure to give a full tutorial everytime befor I leave.

@muhammedkhatib1617 3 жыл бұрын

Hi thanks for this video. My alarm keypad says "Keybus fault call for service" and they keys on they keypad doesn't work when I press them because of this issue. Do you know what could be the problem and what the solution is?

@HowToPM 3 жыл бұрын

Looks like a short somewhere that bug everyting. That might be painful to find if you don't have experience into electronic or electricity. You need to isolate the problem.

@assogan 2 жыл бұрын

Check wiring to keypad

@robertpilallis7067 11 ай бұрын

i have 4 zone. it say. 5is open. ?

@HowToPM 11 ай бұрын

You can have 4 zone on 3-4-5-6 for exemple, but nothing on 1-2

@kangill2411 Жыл бұрын

Great video. I have a DSC PK5500 with Yellow Triangle showing. When I press *2, then View the Trouble it only displays 'Communications'. No error code numbers are shown. My landline phone is working (used to connect to alarm company), but they said they cannot reach my alarm system due to static noise on line. Thoughts?

@HowToPM Жыл бұрын

The PK5500 display the problem in word instead of numbers. I always think it was weird as you got a better idea of the trouble with a code istead of a single word. I would put my system in test and call an ambulance on the keypad to see if comunication work fine. If not, you will need to check you phone cabling.

@myleenmacmillan5528 3 ай бұрын

We have DSC battery that no longer is valid it came with the house and was never removed or uninstalled… now it beeps here and there and we can’t figure out to stop the beeping

@HowToPM 2 ай бұрын

Try holding the speaker button on the keypad. But the real solution is to replace the battery. 😉

@woochie24601 2 жыл бұрын

What does the green swirl mean? My power had gone out for a while and now that it’s back on there is a green swirl button lit up. I think it has something to do with AC? Will it just turn off automatically once the temperature gets back to where it should be?

@HowToPM 2 жыл бұрын

I don't know what is a swirl. But as far as I know the only green light there is, is a check mark and means that all door are closed and the system is ready to arm.

@gingergrosso2559 2 жыл бұрын

I have WT4911/WT8911 Two way wireless outdoor Siren. Press star twice in veiw trouble low battery. No low bettery in zone or keypad. Scrolling to view siren low battery. Low battery in Siren 2. I replace the battery outside but it still showng a triangle. Did I miss a step? Could it be for the strobe? Going to order a new battery.

@HowToPM 2 жыл бұрын

Hum. Sorry, unfortunately I never worked with wireless siren or strobe. Only zone contact. I don't know how they show up when the battery is low.

@tinkandlovu9098 8 ай бұрын

If I press *2 it's says there are no system troubles but continues to beep

@lisatoarmina9437 Жыл бұрын

Hi, I was wondering if you can tell me why my screen is blank but the green check mark is showing on my dsc5501 ? Thank you.

@HowToPM Жыл бұрын

You mean you should see the time?

@manueloliva7313 3 жыл бұрын

Salut pascal jais un problema avec un pk5501 ils ne veux pas se programmer que puis-je faire

@jesseshotme Жыл бұрын

When I press *2 to determine trouble number, no number shows up, just the rapid flashing yellow trouble triangle. What would that mean?

@HowToPM Жыл бұрын

Well... That is confusing... I don't know what to say.

@jrmizzou6925 3 жыл бұрын

Ive a dsc pk5508 Pressing the *2 brings the yellow triangle but no number lights up? The status module blinks amber when not armed. Tried to reset it w no avail. Any suggestions?

@HowToPM 3 жыл бұрын

I'm not sure to get your trouble. Do you have a yellow triangle?

@edgarcabrera7230 2 жыл бұрын

My DSC PK5500 keypads (2) are blank. Are the keypads bad? I checked the main battery and it’s good. Help!!!

@HowToPM 2 жыл бұрын

Firsts model of the keypad had a screen that was easely disconnect able. You can open the keypad to see if it's still sit right in place.

@michaellee6216 3 жыл бұрын

since installing Rogers Ignite my trouble light stays on since there is no power going to it, my tv is on internet now so the cable is no longer needed and so is my phone, the phone is hooked up to the modem, this is Rogers way of saving money, trying to get everyone off the cable system. Is there someway to correct the trouble yellow light ?

@HowToPM 3 жыл бұрын

If you were connected by phone line you will have to switch to internet connection or cellular. But this is not something I can explain on a comment. I will do more video in 2021.

@samhd8071 3 жыл бұрын

Hi sir, do you know why lcd goes blank even if don’t touch it, I have installed 2 dsc and I have same problem with both and recently I changed the battery in main box

@HowToPM 3 жыл бұрын

I seen couple time some LCD unpropely install. Not your fault, it's just easy to be missplace inside the keypad. Normally when you don't touch it it should display time.

@samhd8071 3 жыл бұрын

@@HowToPM it shows the time but since I changed the battery in the main box I noticed this keypad blinking.

@HowToPM 3 жыл бұрын

Hum. Maybe you have touch some wire while doing it. That make me think to a short. Make sure there isn't any red and back wire that barely touch each other.

@samhd8071 3 жыл бұрын

@@HowToPM thank you so much man for replying, I will let you know while it’s fixed.

@edgarcabrera7230 2 жыл бұрын

The pads were working fine and from time to time it works and then it stops working, meaning the pads are showing activity. The system still works but the pads are blank and then maybe a couple of days later, the pads are visible again. This has been happening a lot lately. Confused. Help

@HowToPM 2 жыл бұрын

What are pads?

@edgarcabrera7230 2 жыл бұрын

@@HowToPM keypads

@gaynel1314 4 ай бұрын

I received an 8 - meaning I need to change the time (add it back in after a power outage) Please, anyone - what are the steps to set it to say 3:00 PM ???

@HowToPM 4 ай бұрын

The link to that video is in the description next to trouble 8.

@mickbrown815 2 жыл бұрын

After a power outage the yellow triangle came up I have disconnected the battery also disconnected the power pack from the wall and it still hasn’t cleared not sure what I’m doing wrong

@HowToPM 2 жыл бұрын

You only had to wait for the battery to recharge. As you fully disconect it, now you will have to set back time.

@mickbrown815 2 жыл бұрын

@@HowToPM I set the time but still have the triangle 😩🤦🏽‍♂️

@billydenicola7362 5 ай бұрын

i have d.s.c.power 832 system can it be tie into my cell phone thank you

@HowToPM 5 ай бұрын

There is some service that allow that kind of thing but most require an extra device and sometime a subscription. I don't have any to recommend.

@wallin626 Жыл бұрын

Mine has trouble light and the screen says fire. But I can't clear it and can't set alarm with it in that mode

@HowToPM Жыл бұрын

You might have a smoke detector to reset. You should be able to do it with the double arrow button.

@johnpetrosino3989 Жыл бұрын

I do not want to have my security system monitored as I got rid of my home phone line. But the trouble light is on and once a week it beeps. I was told a technician needs to come out and de program my alarm so it stops trying to look for monitoring. My system shows #4-failure to communicate. How do I de program this so the trouble light is off? Thank you,

@HowToPM Жыл бұрын

It don't remember what section it is by heart but it is a simple option to remove in *8 menu. It takes 15 seconds to remove.

@HowToPM Жыл бұрын

You can ask if they want to guide you by phone but it is possible that they don't want to give you their installer code for security as they probably use the same code for all costumer.

@johnpetrosino3989 Жыл бұрын

@@HowToPM They want to send a guy out so they can charge me $150. Lol.

@johnpetrosino3989 Жыл бұрын

@@HowToPM I have installer code and master code. What are the steps to cancel program please? Thank you

@HowToPM Жыл бұрын

I've just go back to read my installer menu for you. You go to *8 (installer menu) - input installer code - Reach section 015 - Remove 7 (7 is the phone line monitor) - Press # 3 times to exit the menu - Do no hesitate to send a super thanks if I made you save 150$ 😉

@lindapacheco6690 5 ай бұрын

My alarm will not set. I don’t have any number. It just has along beep

@HowToPM 5 ай бұрын

That look like a short somewhere on the installation. That can be anything.

@mickbrown815 3 жыл бұрын

Hi - we lost power for 3 days in Texas recently and my keypad is blank now. No chime for several days and now it’s chiming. I have not reset anything yet but wondering will the system remember my code? Or will I need to reset everything. Thanks in advance like I said I haven’t reset anything yet no clock no date.

@HowToPM 3 жыл бұрын

Hi Mick! Wow this is a long power cut! The system will remember everything except date and time.

@mickbrown815 3 жыл бұрын

How To I just checked everything out yesterday, it did remember my code. I set the time and date! Thank you

@mickbrown815 3 жыл бұрын

How To By the way yes we feel fortunate it was only three days there were some people that didn’t have power or water for five days.

@jsand5389 3 жыл бұрын

@@mickbrown815 Texan here. Had water but no power for 4 days. My DSC has the yellow light and we changed the battery and yellow light still on. 🙄😣

@mickbrown815 3 жыл бұрын

J Sand also if our Internet goes down it’ll take a while to reset and make the connection as well. Good luck

@BaraMidzeh Жыл бұрын

I got number “4” after *2. Turns out phone line was not working - no dial tone. Fixed it. I got the dial tone, but DSC still beeping and *2 shows number 4 again. Help please.

@HowToPM Жыл бұрын

It might show up until the next comunication. Just wait, or call the central to put yourself on test and press the ambulance button.

@BaraMidzeh Жыл бұрын

@@HowToPM It worked perfectly! Thank you! Your video is very well done btw. You make boring instructions not so boring to watch. Keep up the good work!

@MasonWasHere 3 жыл бұрын

Mine shows 1 and 3 I’m focusing on num 3 what if you don’t have it hooked up to the central station bc I don’t want it hooked up

@HowToPM 3 жыл бұрын

It may still look for a phone line. This fonction is activated by default but it can be deactivated. I will eventually do all thoses solution video.

@shivammodi1219 3 жыл бұрын

@@HowToPM can you please make a video on how to remove the telephone line error code

@thefinaldispatch Жыл бұрын

What if I see “133”

@bigbirdwpg 2 жыл бұрын

My Alexor 955 system keeps giving "Siren 1" error. New battery in panel, battery voltage is 13.7. There is no external siren, only the siren in the panel itself.

@HowToPM 2 жыл бұрын

Sorry I'm not familiar with Alexor system

@bigbirdwpg 2 жыл бұрын

@@HowToPM It's a DSC 9155-433

@pyromonster4784 2 жыл бұрын

So my keypad started beeping around 3 beeps and displays the yellow triangle. Then it stops and the triangle disappears. later it will beep again with the triangle, so I ran down there and did the *2 and it shows no issues. Then the triangle disappears again like as if nothing happened. So what could be wrong?

@pyromonster4784 2 жыл бұрын

ok I just checked it again and this time it finally showed the number 3 telephone line. then the triangle will disappear and it will stop beeping. how do I fix this?

@HowToPM 2 жыл бұрын

Well. There is defenitively a trouble with your phone line. Try to reboot your modem and check your phone line. Try to see if you have a tone on your home phone line while the triangle is on.

@youngginkgo2951 Жыл бұрын

How do change battery?I can’t take off keypad

@HowToPM Жыл бұрын

Well you can take off the keypad by inserting a flat screwdriver in the lower cavity but that is not gonna help at all as the battery is in the panel. 😉

@carolyngrizzaffi7759 6 ай бұрын

Warning light on showing a 7. If I hit 7 it shows a large 9 on bottom

@HowToPM 6 ай бұрын

This mean the zone 9 battery is low.

@jonnycadlac297 Жыл бұрын

Hey can you show how to enable wireless devices? Thx

@HowToPM Жыл бұрын

I wish I will eventually make those complete video about DSC. I plan to do a complete tutorial but I have so many project. Adding wireless device is actually in the section 804 of the installer menu. But there might have some other settings to do too.

@user-qj6zq1xo7w 2 жыл бұрын

A new home owner and don’t have a code for this DSC panel! Can you help me reset it

@HowToPM 2 жыл бұрын

This video is the only one that can help you : kzfaq.info/get/bejne/bbypeqWgmJqbiKs.html If it does not work, you only have 2 option left. Call the previous owner, or reset the main bord (but the system would need to be reprogramed).

@QuantumApplications 3 жыл бұрын

Hello! I find your videos very informative. I have a DSC SCW 9045-433 system. Off late the amber triangle continuously shows on it. After checking it using > then * 02 view system troubles then it shows device low battery after that advices to press * again. The message that I get is "Low battery key 02". Once again after pressing *, I get a message "there are no RF Zone Delinq" What does this mean. I am a novice at it. Can you please suggest? Thanks in advance

@HowToPM 3 жыл бұрын

Hi. ''Key'' is probably a remote. The one you can use to arm and disarm from a certain distance. Your keypad won't show numbers of error but directly explain the trouble.

@niranjanbilgi1523 3 жыл бұрын

Thank you so much. The suggestion you made did work. Changed the batteries of the remote and bang...the amber triangle vanished. Your videos are simple and completely understandable. 👍

@kixpan 3 жыл бұрын

How to set date and time on the dsc alarm system

@HowToPM 3 жыл бұрын

kzfaq.info/get/bejne/o8ufobWUuZzScZs.html

@langsonbanda9265 3 жыл бұрын

Like it

@terrgertner2038 7 ай бұрын

*2 and nothing happens. No sound when pressing * or 2

@karimnoorani8337 Жыл бұрын

Hi, I have only triangle sign no sound and numbers

@HowToPM Жыл бұрын

If you d'ont get any code when pressing *2, I'm sorry but I can't hardly see how I can help you.

@TransportSimulatorNationTSN 3 жыл бұрын

Well my one show low battery. We had a power cut a month ago oh, but still show low battery

@HowToPM 3 жыл бұрын

Yea this kind of trouble often show after a power cut. The battery is probably old and is no longuer able to fully recharge. It is still working but it may not last very long now.

@TransportSimulatorNationTSN 3 жыл бұрын

@@HowToPM thanks for the info man.

@reubenthemane7471 Жыл бұрын

Need help my device triggers a panic when arming the systems

@HowToPM Жыл бұрын

what device

@jeanettelennon1673 Жыл бұрын

Where can I get a 7.2vdc nickle metal Hydride rechargeable battery pack

@HowToPM Жыл бұрын

geni.us/3NVZ7

@shivammodi1219 3 жыл бұрын

Mine shows a 3 how do I fix this I want to get rid of the yellow triangle light.

@HowToPM 3 жыл бұрын

I explain it a little bit in that video but I will do more precise video over next year.

@josepha_us3715 2 жыл бұрын

@@HowToPM trying to fix the same issue

@c.teixeira1013 Жыл бұрын

What if nothing shows up after entering *2?

@HowToPM Жыл бұрын

That strange. That might be a problem with the keypad itself maybe?

@c.teixeira1013 Жыл бұрын

@@HowToPM appreciate the quick reply! Tried it again and now just a 1 shows in the submenu. Would the battery be the device battery or something in my electrical panel?

@pontus3825 3 жыл бұрын

What if I press *2 and it shows 1, then it shows nothing after I press 1 again?

@HowToPM 3 жыл бұрын

Is it possible that it show an other 1? I never saw nothing after pressing 1.

@barbarafiore136 3 жыл бұрын

@@HowToPM same thing happens on mine.

@barbarafiore136 3 жыл бұрын

@@HowToPM I get siren fault ! And don’t know what to do. Help!

@sushmarachapudi8855 2 жыл бұрын

My unit stopped chiming when open close the doors

@HowToPM 2 жыл бұрын

Press and hold the music note.

@jayngo23 3 жыл бұрын

Mine shows a few numbers ??

@HowToPM 3 жыл бұрын

It means you have few troubles.

@Krissyloveem Ай бұрын

Didnt teach us how to solve anything...misleading title.

@robyncerone7598 2 жыл бұрын

Pascal I have a trouble code 1 when I press *2. Then nothing. I assume this means the unit needs a battery change only? Do you have a link to a video on how to change that? It is a DSC Powerseries, PK5500/PK5501/RFK5500/RFK5501/RFK5564 keypad. Thanks

@HowToPM 2 жыл бұрын

You must press one again to see what the trouble is.

@allisonferreira9090 Жыл бұрын

Jumping in here, as I have a similar problem. After *2, I am shown 1. I press 1, but the screen does not change and continues to show 1. Does this mean it is error 1 sub 1 (battery issue) or is there an issue accessing the subcategory? Thank you for this fantastic video!! Glad I didn’t press the triangle button

@nandanisharma869 2 жыл бұрын

What does 4 mean? I'm confused 😕

@HowToPM 2 жыл бұрын

It's the temper of an extension module that is open. Might be a pannel door that is open, or just a jumper that is not install.

@HowToPM 2 жыл бұрын

Sorry I did get cufuse with 1-4. 4 only is because you alarm system tried to comunicate with the alarm central and it failed. So it's actually not able to send alert to the central because of your communication device or wiring.

@nandanisharma869 2 жыл бұрын

Thank u this helped so much

@timothyandoh8968 8 ай бұрын

Mine is 178

@timothyandoh8968 8 ай бұрын

Mine doesn't use a battery

@neftygonzalez7354 Жыл бұрын

why my siren keep going 😢

@mohammadal-harbi2916 3 жыл бұрын

please, let know how can i change or add phone number in the system to connect me during alarm

@HowToPM 3 жыл бұрын

The DSC panel can't contact you directly. It's made to communicate to the alarm central. You would need a third party module to do that kind of comunication.

@jrmizzou6925 3 жыл бұрын

U can program a number to communicate w u directly