How to Spray The Liquid Concepts Activator

Рет қаралды 34,293

10 жыл бұрын

Bryan from Liquid Concepts showing how to set up your activator gun and how to spray the Liquid Concepts activator for the water transfer printing. If you have any questions please contact us at 501-261-1616, by email at info@liquidconcepts.com or you can visit our website at www.liquidconcepts.com.

Пікірлер: 24

@jaloi5862 3 жыл бұрын

Thank you thank you THANK YOU!! I started trying to dip about a month ago and went through a ton of film with horrible results. I knew it was the activator application but all the other videos i watched were "20psi" "12-16"" no luck at all. I watched your video and set my gun up as you recommend it and NAILED it! Can't say enough good about your videos!

@ryancooling61 10 жыл бұрын

Great video Bryan!

@steveclarke2189 6 жыл бұрын

Very helpful

@parrishstuckey1 10 жыл бұрын

awesome thanks, i've been doing just what im not suppose to do

@finetec8911 7 жыл бұрын

hi i have a question my English is not so good sorry how much pressure you sprühst I activator have the same gun as you. like ask you the material quantities I pulled the lever all the way back and then turned the screw one turn , Thank you for your help

@jc44987 9 жыл бұрын

Can i use a 1,2mm needle for the Spray Gun for the Activator

@Emag-666 6 жыл бұрын

What about with the aerosol can you all sell?

@rainsanchez1390 5 жыл бұрын

So which side of the film goes down onto the water.?

@dozercorbin2694 4 жыл бұрын

I know this is an older video, 6 years or so. You were referring to the air pressure going into the spray gun, approx 75 psi, and the pressure coming out the tip, approx 8 to 10 psi. How do you gauge that?

@Hammerback972 3 жыл бұрын

Gauge on the air compressor says 75, gauge on the paint gun is 8-10

@073731002 7 жыл бұрын

hey bryan since the activator has chemicals like xylene in the mixture do you have extractor fans?

@LiquidConceptsUSA 7 жыл бұрын

We do not have a extractor fan but several of my customers do. We wear our respirator mask when spraying.

@073731002 7 жыл бұрын

Liquid Concepts but when you spray it aren't you worried about how flammable xylene is

@LiquidConceptsUSA 7 жыл бұрын

We have had all of our spraying testing based on the amounts sprayed and the chemicals and a respirator is perfectly fine for what we spraying. They do make some activators that are available that are almost completely xylene free.

@JulianIbanez13 7 жыл бұрын

well i just discovered why i lost my graphics last night, too much activator. but i have a question, does the water really have to be brought up to 85/90 degrees?

@LiquidConceptsUSA 7 жыл бұрын

No but cooler water will require longer soak times for the films.

@JulianIbanez13 7 жыл бұрын

Liquid Concepts thanks i'm going to try this weekend again with the remaining of my film and then if works then i buy another film and begin correctly.

@LiquidConceptsUSA 7 жыл бұрын

Sounds great!

@michaelgrays7327 6 жыл бұрын

so 6-8 inches distance from the film at 8-10psi on the gun

@KarelleDIY 3 жыл бұрын

Doesn’t that stuff stink? It stinks so bad when I spray it I use a gas mask.

@killabrozzard6836 10 жыл бұрын

I've been spraying that high always have and I don't get those results but also you was moving back and forth way to fast on your "proper technique " you was passing real slow and when you went to the next piece of film you was just going back and forth and back and forth not giving the activator not time to settle I use your activator high up like that no problem

@deerbeerdeerbeer 8 жыл бұрын

huh?????i dont get it. The proper amount of activator close to the film gets you a good dip. Way too much activator from high up gets you a bad dip. OK.....How about spray the correct amount from both close...THEN from high up and well see what the difference is..EVERYONE already knows that to get a good dip you need to apply the correct amount of activator.

@KarelleDIY 3 жыл бұрын

He never wears a mask. Does anybody else wear a gas mask or am I the only one?

@Hammerback972 3 жыл бұрын

Of course. He was just experiencing freedom before the Kung flu and the plandemic hit. Amazing almost 8 years later and he's still alive. Probably sprayed that whole gallon by now.