How to stabilize a wood crack

  Рет қаралды 1,221,599

Totally Handy Shorts

Totally Handy Shorts

Жыл бұрын

Explore a wide variety of content in our carefully curated KZfaq playlist: • Binge-Worthy Content
Find more amazing tips at @TotallyHandyShorts #shorts

Пікірлер: 157
@DarrenTheDead
@DarrenTheDead Жыл бұрын
Notice the lack of glue that makes it to the bottom of the crack by pounding. Hint apply glue to both surfaces.
@nickanderson8305
@nickanderson8305 Жыл бұрын
I'm suprise no one noticed that. This is not stabilized by any means
@roarke222
@roarke222 Жыл бұрын
My uncle built his barn by hand, meaning hand tools only, including felling the trees and cutting the lumber by hand. Not only did he make the importance’s of gluing both the hole and the dowel clear, he also showed me to use only enough glue to coat the surfaces but also to give it a minute to tack before inserting the dowel(s)
@outdoorcoaching
@outdoorcoaching Жыл бұрын
Exactly.This makes no sense and it's really bad advice...
@donaldduck4867
@donaldduck4867 Жыл бұрын
Fail!🤦‍♂️
@ianbelletti6241
@ianbelletti6241 Жыл бұрын
At least the grain of the dowels was 90 degrees to the grain of the block.
@anthonys439
@anthonys439 Жыл бұрын
That crack ain't stabilised at all 🤣🤣🤣
@WorkingViews
@WorkingViews Жыл бұрын
That's honestly going to just crack more. Bow ties are the way to go.
@GibonCzo
@GibonCzo Жыл бұрын
you forgot to apply glue to the hole, you pulled all the glue off the pin. the dowel at the bottom is practically dry.
@taintedsasquatch398
@taintedsasquatch398 Жыл бұрын
I got a better way, use a different piece of wood.
@neiljohnson7587
@neiljohnson7587 Жыл бұрын
Woods expensive so that’s not really a better idea
@DavidYun-vx4de
@DavidYun-vx4de Жыл бұрын
I agree with you. Cost is not important than safety.
@bastienpabiot3678
@bastienpabiot3678 Жыл бұрын
@@DavidYun-vx4de cracked wood is not unsafe if used corrzctly and stabilised like in the video6, and not necessarily cheaper either Sometimes you don't have the perfect piece of wood and you work with what you have
@HudsonFamily7
@HudsonFamily7 Жыл бұрын
😂😂😂 o
@NuttyCuts_
@NuttyCuts_ Жыл бұрын
@@neiljohnson7587 expense isn’t a factor when that crack could lead to something breaking and hurting someone
@RuR-ru
@RuR-ru Жыл бұрын
Наверное это художник!! И ОН так видит процесс работы с деревом ))!!!!!
@timtim4726
@timtim4726 Жыл бұрын
Он такой же художник по металлу)))
@teresabrown3914
@teresabrown3914 Жыл бұрын
You can mix the shavings with wood putty or wood glue and fill in the crack and after it dries and is sanded it will match perfectly
@makarych7007
@makarych7007 Жыл бұрын
Как то хреново чепики заклеил, нужно обязательно промазать отверстие, и потом чепики. И клей нужен не в таком количестве!
@user-fb1eh9jr8t
@user-fb1eh9jr8t Жыл бұрын
Я только не понял "на фига", по хорошему надо или прореить, а лучше вырезать и переклеить.
@VeteranVandal
@VeteranVandal Жыл бұрын
Is there a reason to leave the crack open for anything to get in? You stabilized, but there's still a problem. Shouldn't that be covered at least?
@xpndblhero5170
@xpndblhero5170 Жыл бұрын
If you're gonna go through all the work you might as well just fill the crack w/ epoxy.....
@AndrewDeLong
@AndrewDeLong Жыл бұрын
Epoxy and a bowtie would do wonders
@InchFab
@InchFab Жыл бұрын
@@AndrewDeLong as wood a new peace of would
@AndrewDeLong
@AndrewDeLong Жыл бұрын
@@InchFab Trust me, a lot of customers like the split look with epoxy and bowties.
@InchFab
@InchFab Жыл бұрын
@@AndrewDeLong I do epoxy work. I understand. A lot of people have bad taste also. I have to talk people out of a lot of tacky and ugly stuff.
@AndrewDeLong
@AndrewDeLong Жыл бұрын
@@InchFab Agreed. Some people have...odd tastes (to say the least).
@ikerortizdeurbinalopez2216
@ikerortizdeurbinalopez2216 Жыл бұрын
in spain we have a word: "chapucero"
@stuartbromley3513
@stuartbromley3513 Жыл бұрын
Sloppy
@timtim4726
@timtim4726 Жыл бұрын
All the glue left on upper part.
@SW-qr8qe
@SW-qr8qe Жыл бұрын
Fill it with clear epoxy and it will look cool
@gzahirny
@gzahirny Жыл бұрын
What exactly did this accomplish? Wood is still cracked, the gap didn't get smaller, so why would anyone waste time doing this?
@humancattoy7767
@humancattoy7767 Жыл бұрын
Works wonders for people who regularly use reclaimed wood.
@xMrjamjam
@xMrjamjam Жыл бұрын
Never wipe away wet glue you'll log the pores of the wood. Let it dry and chisel the dried excess glue off
@SosShortsComedy
@SosShortsComedy Жыл бұрын
Bela reconstrução !
@zacksrandomprojects9698
@zacksrandomprojects9698 Жыл бұрын
Me: "Oh its cracked, I'll just fill it with caulking and smooth it before I paint it."
@Sheeeeshhhhhh
@Sheeeeshhhhhh Жыл бұрын
Duck tapes are the best for this
@garyjones783
@garyjones783 Жыл бұрын
As other comments have been made about the glue being scraped off once the dowel reaches the bottom of the hole,…. This is still amateur based on the glueing process.
@ryanbianchi6582
@ryanbianchi6582 Жыл бұрын
What we learned here is that’s obviously far too much glue
@TheIMadeThat
@TheIMadeThat Жыл бұрын
No, this is not what you do. You have to put a butterfly pattern( or another pattern ) into the cracked side.
@bvictory5698
@bvictory5698 Жыл бұрын
It’s like he saw it so fast! Like his welding videos... I mean... spot welding videos.
@user-ed8zb1ri5p
@user-ed8zb1ri5p Жыл бұрын
По уму, надо клеем отверстие мазать, а не чёпик.
@user-ro2yb8ju8y
@user-ro2yb8ju8y Жыл бұрын
Пилка огонь 🔥🔥 ))
@nobody-ep1bu
@nobody-ep1bu Жыл бұрын
Why won't you make a hole enough to the length of wood nail. You know, to make it more satisfying to watch.😭
@TotallyHandyShorts
@TotallyHandyShorts Жыл бұрын
we'll think about it
@joek3697
@joek3697 Жыл бұрын
You can easily make this repair with a table saw and some string. Beginner mistake
@omatheuzaoem2266
@omatheuzaoem2266 Жыл бұрын
Não é mais segura jogar fora?
@TotallyHandyShorts
@TotallyHandyShorts Жыл бұрын
nao e muito mais divertido asim
@ryanjones9305
@ryanjones9305 Жыл бұрын
How to take a $4 piece of wood and make it into a $40 piece of wood in two easy steps.
@user-fb1eh9jr8t
@user-fb1eh9jr8t Жыл бұрын
Я не понял смысл этой операции, не лучше было отфрезеровать паз и вклеить рейку?
@mircomuntener4643
@mircomuntener4643 Жыл бұрын
That did not need stabilizing, nor did those dowels do any stabilizing. If you want to show off, drop a bowtie in it. If you want to look like a tough guy, hammer up a couple dogsand slam them across the crack. The only cracks that need stabilizing are in slabs, not in centercut cants like this.
@davidashton2361
@davidashton2361 Жыл бұрын
Please mind your language.😄
@thecaramelcasanova2123
@thecaramelcasanova2123 Жыл бұрын
He wasted so much glue= extra work
@rudepug4
@rudepug4 Жыл бұрын
Dont use cracked wood
@YouTubesuckschlonge
@YouTubesuckschlonge Жыл бұрын
Yeah 🤣🤣 toss that sh*t in the log burner and find a good piece
@uzi9587
@uzi9587 Жыл бұрын
Yeah u decorated the wood
@birisuandrei1551
@birisuandrei1551 Жыл бұрын
Why not just cut the part that is cracked off and insert a piece of wood that fits in the crack...thats way more stable than wtf this is
@tincupnickleboythe1st700
@tincupnickleboythe1st700 Жыл бұрын
Gang nail lol
@jamesowen21
@jamesowen21 Жыл бұрын
Why not dado out the entire cut, fill it with wood cut to size, glue and clamp it
@davidashton2361
@davidashton2361 Жыл бұрын
Dado out? Wot's that mean? JHC!
@jamesowen21
@jamesowen21 Жыл бұрын
@@davidashton2361 look up dado. Look up rabbet. Lool up tongue and groove
@davidashton2361
@davidashton2361 Жыл бұрын
@@jamesowen21 I don't need to look them up. I know exactly what they all are because I have been a professional carpenter/joiner/site fixer for most of my working life. I have worked in joinery shops as a bench carpenter, in banks and the Albert hall site fixing and been self employed making and fitting doors and windows and fitting kitchens. Also roofing and shuttering in Germany (I speak a modest amount of German from my days stationed in Germany in the army) I trained as a land surveyor while in the army and when I left the army I did a 3 year contract out in Saudi Arabia land surveying, so don't front me about my knowledge of construction work or joinery etc. I've probably forgotten more than you'll ever know because I'm 76. Sonny.
@jamesowen21
@jamesowen21 Жыл бұрын
@@davidashton2361 Well my mama tols me to respect my elders. So I wont remind you that if you know sonething already why you asking "whats a dado". Its a groove cut in a board dummy. Thanks for your service. Retired myself. Stop asking questions you already know. Very unbecoming
@davidashton2361
@davidashton2361 Жыл бұрын
@@jamesowen21 I've never heard of a dado in connection with a groove. Must be an americanism. I have used the term dado rail in connection with a moulding that is fixed at about waist height in a room, usually above panelling, but not used as a verb to describe channeling out a groove in wood. However, I will concede that there are minor differences in american english and english english. To ask me to look up tongue and groove, really? My cats know what tongue and groove is. From this I deduced that you were a rank amateur of tender years, which prompted my outburst. However, now that you have revealed that you are also a retiree I apologise, but I still have reservations about your woodworking experience. Be that as it may, I find the american way of expressing gratitude to former service personnel very endearing, so thank you for that. I was in the army for 14 years and the biggest mistake was opting to leave. I was totally unsuited for life in a civilian enviroment. I should have stayed in and benefitted from more rank and longer service leading to a much better pension. My involvement in posting comments about other peoples woodworking skills is prompted by my desire to 'wind people up' out of amusement. Frankly, some of them really don't appear to have much experience and are only using this medium to make money out of even less able people. In the real world of carpentry and joinery they wouldn't have a hope in hell of earning a living. That's not to say they're wrong necessarily, but in the competitive world of, say, site fixing, to only hang one door a day doesn't cut the mustard. More like 5 to 10 is the norm, depending on site conditions. I know that in America a lot of the tedious work has been done, like the lock positions being already cut out etc. Where here in England we have to do that on site usually and therefore the rate of door fitting lowers. Even so, 5 to 10 doors is the norm.
@wumpa100
@wumpa100 Жыл бұрын
You can make that look good too
@kinnikuzero
@kinnikuzero Жыл бұрын
Ahh yes, a nicely stabilized crack
@davidashton2361
@davidashton2361 Жыл бұрын
That's what the Bishop said to the actress. 😄😄
@julianm2888
@julianm2888 Жыл бұрын
What glue do you use?
@gzahirny
@gzahirny Жыл бұрын
He used generic wood glue
@austinsthole8486
@austinsthole8486 Жыл бұрын
Wood doesn't have cracks. If you want crack you'll have to get it somewhere else. That there is called split.
@Balls607
@Balls607 Жыл бұрын
Lol irony and all
@davidashton2361
@davidashton2361 Жыл бұрын
No, it's called a 'shake'.
@davidashton2361
@davidashton2361 Жыл бұрын
If you want a spliff you'll have to go to the same place where you get your crack.
@jonahnesmith7004
@jonahnesmith7004 Жыл бұрын
I should call her...
@andreas1364
@andreas1364 Жыл бұрын
I dont get it
@davidashton2361
@davidashton2361 Жыл бұрын
Neither does anybody else! 😄😄
@consumer1843
@consumer1843 Жыл бұрын
How about a cracked wood column?
@briannowdesha3986
@briannowdesha3986 Жыл бұрын
Yeah or just get a new piece of wood that doesn't have a huge Kraken
@realyuriksid
@realyuriksid Жыл бұрын
Весь клей остался на поверхности.... И вообще не понятно, для чего это коротыш нужен. Хотя, если его закруглить, то получится тело буратино, а эти чёпики будут похожи на пуговицы. Ждём продолжения по созданию буратино
@user-og3qy8tx2z
@user-og3qy8tx2z Жыл бұрын
А если чопик с зади будет а?
@realyuriksid
@realyuriksid Жыл бұрын
@@user-og3qy8tx2z ещё надо определить, где у этого палена зад....
@user-og3qy8tx2z
@user-og3qy8tx2z Жыл бұрын
@@realyuriksid для этого надо один чепик с обратной стороны забить😂
@realyuriksid
@realyuriksid Жыл бұрын
@@user-og3qy8tx2z такое ютюб не пропустит
@feniksflash166
@feniksflash166 Жыл бұрын
Что Где Зачем А ТЕПЕРЬ ВНИМАНИЕ ВОПРОС НА..............Я ????????. отрезал лишнее кинь в топку😉😉😉
@mobidrive1171
@mobidrive1171 Жыл бұрын
Кому как, а я бы обработал и трещину ,и, чопики
@RavinderSingh-hi7so
@RavinderSingh-hi7so Жыл бұрын
Instead of cleaning excess glue 🤔🤔🙄🙄 Drop into the hole 1/4 of your method .... 🙏🙏🤣🤣
@joerice1439
@joerice1439 Жыл бұрын
For anyone asking why? Time, but not resources. God damnit i blew on my phone to make the wood chips go away. Wtf
@davidashton2361
@davidashton2361 Жыл бұрын
And?
@joerice1439
@joerice1439 Жыл бұрын
@@davidashton2361 and nothing. Thats it. Tard
@zxcursred.
@zxcursred. Жыл бұрын
i'm gay i love mans
@donwimberley4772
@donwimberley4772 Жыл бұрын
You posed to put glue inna hole FIRST.....
@davidashton2361
@davidashton2361 Жыл бұрын
Yeah, irriot!
@05jcm
@05jcm Жыл бұрын
Just replace the piece.
@AndrewDeLong
@AndrewDeLong Жыл бұрын
Depending on what's being built, some customers want the split pieces to be used.
@alexniklas8777
@alexniklas8777 Жыл бұрын
Надёжнее синей изолентой обмотать
@dustinbryan841
@dustinbryan841 Жыл бұрын
Wuuuut
@georgejung3083
@georgejung3083 Жыл бұрын
Don’t pick that at the lumber yard get a full one ☝️
@loganraimer
@loganraimer Жыл бұрын
Deff not the right way
@Kevthebish
@Kevthebish Жыл бұрын
Yep, the crack is still there
@AndrewDeLong
@AndrewDeLong Жыл бұрын
The video said "stabilize" not "remove or close"
@davidashton2361
@davidashton2361 Жыл бұрын
What! Where you stashed it before?
@cancanphotographer5044
@cancanphotographer5044 Жыл бұрын
Kardesim !! O tutkali neden kullandin ???????
@gigakutaladze.5492
@gigakutaladze.5492 Жыл бұрын
Can you tell me name of this glue?
@CeeJayThe13th
@CeeJayThe13th Жыл бұрын
Jermaine
@gigakutaladze.5492
@gigakutaladze.5492 Жыл бұрын
@@CeeJayThe13th thank for answer
@CeeJayThe13th
@CeeJayThe13th Жыл бұрын
@@gigakutaladze.5492 I was just making a joke lol. Judging by the bottle, it's Titebond II but literally any glue labeled "wood glue" will work just fine. Some are formulated for more specific tasks but they will all work out. I personally like Gorilla *Wood* Glue (not regular gorilla glue as it expands but specifically the wood glue) because it's cheaper in small quantities where I live and is readily available. In a pinch, any PVA glue will bond wood such as school glue but it's not really recommended.
@gigakutaladze.5492
@gigakutaladze.5492 Жыл бұрын
@@CeeJayThe13th thank ,that you shared me your experience
@gordonarneson2070
@gordonarneson2070 Жыл бұрын
Now throw it in the wood stove where it should have went to start with
@davidashton2361
@davidashton2361 Жыл бұрын
Yeah! 🤣
@user-sw1oy7vr2b
@user-sw1oy7vr2b Жыл бұрын
И-и-и- и?
@robertgemski6524
@robertgemski6524 Жыл бұрын
But why 🤔
@saimaiqbal8551
@saimaiqbal8551 Жыл бұрын
Very bad & weak technique used here.
@jacekz1456
@jacekz1456 Жыл бұрын
No I !!!
@krupzug5359
@krupzug5359 Жыл бұрын
Okay, enough bullshit for today
@marjanaking404notfound3
@marjanaking404notfound3 Жыл бұрын
That's it? Wow..
@xhunter2479
@xhunter2479 Жыл бұрын
Hi
@trolln_gta7926
@trolln_gta7926 Жыл бұрын
Why didn't you line the grain up properly? Either with the grain of the piece or at the very least with each other. Not cool.
@richardwelsh7901
@richardwelsh7901 Жыл бұрын
When you find yourself in a situation to actually need to perform such a repair, I don't think aesthetics are going to be much of a priority
@emba_dareepolreeiiith1063
@emba_dareepolreeiiith1063 Жыл бұрын
bowtie?
@oskarlaudan
@oskarlaudan Жыл бұрын
This Channal Is called totally HANDY shorts, that means you're german?
@linus8976
@linus8976 Жыл бұрын
見た目悪くて草
@digitalnorp890
@digitalnorp890 Жыл бұрын
Anybody else think they would’ve just filled it with like silicon or glue or something. I’m not drilling holes into the wood that’s to much work😂
@jonesy12221
@jonesy12221 Жыл бұрын
At least put the grain on the dowels going the same way as the grain on the timber.
@davidashton2361
@davidashton2361 Жыл бұрын
End grain doesn't match with horizontal grain. End grain is end grain and horizontal grain is, well, horizontal grain. The only way to disguise this is to make the dowel shorter and pellet over the end and then you can match the grain, provided you select a pellet with a matching grain or make your own from a similar grained piece of timber. I agree with somebodys comment about putting glue in the hole as well. Actually, I didn't see the point of dowelling the piece of timber in the first place - as somebody else said, just get a decent piece of timber to start with. Sorry to say it, but a lot of people slagged this exercise. Nice one, Bro!
@jonesy12221
@jonesy12221 Жыл бұрын
@@davidashton2361 I'm not slagging it or trolling. When I put a pellet or grain plug in even a dowel I'll match the grain of timber its going in to. Standard practice! This is clearly a vid to show how to secure a piece of timber thats already been installed & then started to split & shrink. Just prevents further parting.
@Ivan-Dybovik
@Ivan-Dybovik Жыл бұрын
Нехватает смекалки чтобы таких трещен небыло, наши предки при раскрой леса серцевину вырезали и выбрасывали она всеровно лопнет.
@bubyu507507
@bubyu507507 Жыл бұрын
何なのか判らないが。
@BaggedTLX
@BaggedTLX Жыл бұрын
or better yet hear me out get a different piece of wood. god bro life changing idea right?
@jamesowen21
@jamesowen21 Жыл бұрын
Stop buying wood with crack. Go to a good neighborhood
@davidashton2361
@davidashton2361 Жыл бұрын
That other guy said that as well. Must be right. 🤣
@davidashton2361
@davidashton2361 Жыл бұрын
This is fun, isn't it. 😃
@shepshepson
@shepshepson Жыл бұрын
How about you use an actual piece of wood instead of cutting a giant slot in it and "repairing" it
@jordanbachynski8054
@jordanbachynski8054 Жыл бұрын
This is a terrible way to fix a crack. Butterfly’s aren’t difficult
@seanmyers227
@seanmyers227 Жыл бұрын
Wow. That's not very good at all
@Lion.blood30
@Lion.blood30 Жыл бұрын
🤦🤦🤦
@shrutibagde573
@shrutibagde573 Жыл бұрын
Hey, this is from Family Handyman just want to follow up. We are still interested in your video, please contact us back to discuss more information
@AG_92
@AG_92 Жыл бұрын
Are you really from Jukin Media? Because if it's a scam, you can get reported.
@alfredgood6978
@alfredgood6978 Жыл бұрын
A krewsaider is here...
@AG_92
@AG_92 Жыл бұрын
@@alfredgood6978big OOF, please learn how to spell first it's crusader not krewsaider 😂😂😂
@shrutibagde573
@shrutibagde573 Жыл бұрын
@@AG_92 Yes! I am very much aware of the consequences, but this is not a scam. This is from Jukin Media and TMBI brand Family Handyman.
6 Best Hacking Tools / wood connection tips / DIY
16:03
Hammer Sound - The Jig Shop
Рет қаралды 568 М.
Miss Delight show something (Poppy Playtime 3 Animation)
00:11
Өнер Қырандары - Мешіт 2024
34:59
ONER KYRANDARY
Рет қаралды 674 М.
Woodturning - YEW Can't Be Serious?
16:17
Jack Mack Woodturning
Рет қаралды 8 МЛН
Impossible Woodturning. Unusual devices. Oak firewood. Diy.
17:44
Pavel Evmenov
Рет қаралды 7 МЛН
5 New Inventions Homemade Tools that not everyone knows about
16:52
Few people know these Ingenious Tips and Tricks of the House Masters That Help ▶10
6:02
Making a simple but stylish product from wood. Woodworking.
8:26
Repair a Rusty Japanese Knife over a month
30:08
JSK Projects
Рет қаралды 1,8 МЛН
Woodturning Beautiful Walnut Resin Bowl
15:32
Square and Level
Рет қаралды 1,8 МЛН
No Epoxy Required.
31:22
Olivier Gomis
Рет қаралды 1,5 МЛН
Завязка рук в мексиканском стиле🤯
0:44
Story-Bytes
Рет қаралды 2,8 МЛН
КУХОННЫЕ НОЖНИЦЫ
0:47
Сергей Кагилев
Рет қаралды 11 МЛН
Best Mom ever #shorts by Secret Vlog
0:14
Secret Vlog
Рет қаралды 12 МЛН
Малышка Поняла, что Её Папа Ушёл... 💔
0:31
Глеб Рандалайнен
Рет қаралды 5 МЛН