is it just me, or does there appear to be a second audio issue going on here?
@oldschoolmechanic7771 Жыл бұрын
Don’t know I’ll have to listen again
@lexhawkins74428 ай бұрын
Not your imagination - there’s some kind of audio playing in the background.
@lostintime86516 ай бұрын
You're just going crazy it's the voices in your head😮
@user-dm4yo8tp5z3 ай бұрын
I definitely heard noise in the background as well
@josephdertinger98572 ай бұрын
same here
@fxpestoperator5527 Жыл бұрын
This is a GREAT video!!! Wish I could have seen the wiring for the jump starter, but thanks for making this Brother! Awesome!!!!!
@oldschoolmechanic7771 Жыл бұрын
Thank you for watching. I actually just put the booster pack straight to the starter. I didn’t do any wiring on this one as far as key switch, starter solenoid, battery.
@fxpestoperator5527 Жыл бұрын
@@oldschoolmechanic7771 Thanks Brother! I have a 13.5 hp woodsplitter and when you pull the cord it sometimes snatches back - trying to break my wrist!!!! Needs a starter bad! 🤣
@oldschoolmechanic77719 ай бұрын
Sorry for not responding about pulling the rope out of your hand I’ve had a busy summer. You might check your fly wheel key to see if it’s sheer that could be causing the kickback. Another trick you can try is try not to start the motor in between the compression stroke pull on the rope until you feel the resistance and then pull through it If that makes sense
@stevethomas2114 ай бұрын
What and where can you find a flywheel for the motor that you want to change over to a electric start????
@langthangbolsa.42134 ай бұрын
GREAT VIDEOS,I LOVE YOUR JOB DONE!
@oldschoolmechanic77714 ай бұрын
Thank you I appreciate it
@iammanhearmeroar110618 сағат бұрын
Ok so where do we get these parts? Starter, flywheel etc...
@stevethomas2114 ай бұрын
After thought, what is the clap do you set it at??? when replacing the flywheel.
@REVNUMANEWBERN2 ай бұрын
Use a typical business card, don't ya just love the YT clips that give you virtually NO or NOT enough info?
@dennytuma Жыл бұрын
you just saved the day got a blown up electric start 500cc that i was going to tear apart found a new pull start 500cc for 100 dollars going to do what you just did
@oldschoolmechanic7771 Жыл бұрын
Glad you found it to be beneficial. Thanks for the comment
@user-ot1hn1yb6y6 ай бұрын
can this be done to any pull start snowblower...no matter the brand
@oldschoolmechanic77716 ай бұрын
Problem would be if the snowblower has a ring gear on the flywheel. If it does then there would be a way to do it because then it had the option when it was new. If not then you could do some research to see if that model number of engine came out with a starter option then you would have to change the flywheel and find a starter just like the video. I hope you understand what I saying. If not you could call me during the daytime and I could explain it better. 316 312 8704
@MJM7502 ай бұрын
so what about part number for starter? or can any starter be used?
@paulmonk78202 ай бұрын
Why didn't you show adjusting the coil gap? 😮
@oldschoolmechanic77712 ай бұрын
Well I didn’t have to because the flywheels were the same flywheel other than one having a ring gear. I try to cover all the points but I do miss some
@REVNUMANEWBERN2 ай бұрын
SO, you don't actually show it working???? : (
@oldschoolmechanic77712 ай бұрын
Sorry I probably could have started it. It’s pretty straightforward once you get it all together. It will act like a regular electric start engine minus the luxury of a key switch starting system
@KMB232318 ай бұрын
Quick question...I just wired up a RER snapper with a key start, replacing the recoil on an 11hp B&S. After running all wires, replacing flywheel, installing solenoid, starter & battery I realized the starter is turning the flywheel in the wrong direction. Is it possible to change the direction of the starter by switching the magnets inside or I read about changing my wiring. I hope you can give me some insight. Thanks
@oldschoolmechanic77718 ай бұрын
Modern Briggs engines run in a clockwise direction. I’m trying to remember if I ever recall of one turning in the opposite direction. I have seen starters turn backwards because of the posts on the battery being hooked up backwards. You can possibly turn the casing of the starter to point in the opposite direction where the gear would be on the opposite end. Hope that makes sense
@paulmonk78202 ай бұрын
The casings I've seen will only fit one way. There is a notch on the bottom where the brush plate wire terminal fits. 😮 😊
@en2oh Жыл бұрын
what's the part number for the ring gear flywheel?
@oldschoolmechanic7771 Жыл бұрын
The ring gear doesn’t have a part number. It comes with the flywheel but you can find a junked out Briggs and the flywheel ring will come off and will fit on what you have. A 12 hp or a 14.5 hp. I do believe even a vtwin ring gear will work too
@gregkania7887 Жыл бұрын
Do you know what model number bridge and Stratton put this engine under I have exactly the same one I cannot find it
@oldschoolmechanic7771 Жыл бұрын
I will do some checking. I can tell you that you can find a another used overhead flywheel from a 10 to a 14.5 hp Briggs and the ring gear can be removed and installed on that flywheel that you have as well
@drummer4hire248 ай бұрын
Just the info I needed.... thank you sir. YEP, i'm about done with plastic pawls.... @@oldschoolmechanic7771
@vanstechcorral4 ай бұрын
Nothing like those plastic gears that strip with compression kick back. Too much plastic either way.
@oldschoolmechanic77714 ай бұрын
Yes they can tear things up. Check your valve settings. They could have to much clearance between the rocker arm and the top of the valve cap causing that kick back. Should be set at .005 on both valves.
@vanstechcorral4 ай бұрын
There is no adjustment possible to decrease the excess valve lash on the opposed twin flathead.
@oldschoolmechanic77714 ай бұрын
Ah thought you were working on an over head valve.
@vanstechcorral4 ай бұрын
@@oldschoolmechanic7771 It's too bad there wasn't provision in the design to be able to use shims for adjustment. Seems like it ought to have been a no brainer
@oldschoolmechanic77714 ай бұрын
I agree. Only way to get closer clearances other than some in depth modifications is to get new valves
@steelthunder76 Жыл бұрын
Good video thank you I will subscribe
@oldschoolmechanic77716 ай бұрын
Thank you. Sorry I don’t always see the messages. I hope I was able to help