How to tighten adjust valves on a 2002 300EX

No video

How to tighten adjust valves on a 2002 300EX

Рет қаралды 12,685

Күн бұрын

Thanks for watching Please like And subscribe and always come back to #FlatheadGarage anyways guys I always upload when I got a video to upload Have a nice day and hope you enjoyed.
-
MUSIC BY • Dj Quads - Changes
-
MUSIC BY www.davidcutter...
-
MUSIC BY / . .
-
MUSIC BY / audiolibrary
-
MUSIC BY chukibeats.com/
-
CHUKIBEATS CHANNEL www.youtube.co....
-
MUSIC BY • Video
-
MUSIC BY • Dj Quads - Changes
-
MUSIC BY DJ QUADS CHANNEL
/ @djquadsofficial
-
check me and Sam out on our Instagram
-
/ flatheadgar. .
-
...
-
FAN MAIL:
Ethen Hargraves
PO Box 544
Rose Hill,VA 24281

Пікірлер: 31

@marijualan8677 3 жыл бұрын

I noticed on mine, that an upside down roberts head screw works nicely to adjust/hold while tightening 😉🍻🍻🍻🖖

@dannielrogers9566 4 жыл бұрын

This is the most helpful video ever thank you so much I’ve been holding off on doing this for 2 years now because I couldn’t find a helpful video

@FlatheadGarage 4 жыл бұрын

Thank you it means a lot

@fly82high 3 жыл бұрын

Your video was perfect man! My 300ex runs like a top. Ticking has stopped. You can send me the bill! Lol

@flames_6265 4 жыл бұрын

Best video on KZfaq

@FlatheadGarage 4 жыл бұрын

Thank you it means a lot

@flames_6265 4 жыл бұрын

Flathead Garage no problem

@connersnow298 3 жыл бұрын

Awesome filming and edits to

@hillbillyroyalty4792 3 жыл бұрын

nice video but I can't seem to find anything on the internet where you have to spin the motor to the certain symbols to adjust the intake and the exhuast there should be 3. I'm pretty sure its the same quad but the years 1999 if you could find that that would be life saving

@connersnow298 3 жыл бұрын

Awesome vid and bike

@tristankemplin6766 4 жыл бұрын

I'm almost 100% sure that it supposed to hold that center bolt still when tighting the valves so I have to use a wrench and not A ratchet

@alexbecrazy9175 2 жыл бұрын

hvac wrench 🤝

@beauhunter2123 4 жыл бұрын

My valves have been tapping the past few hours of riding.... is it real bad to keep riding with them making a tapping sound?

@FlatheadGarage 4 жыл бұрын

It ain't terrible but I would tighten your valves and keep a check on your oil

@ryanmicklo1616 4 жыл бұрын

Newer to working on quads, how do you know the valves need to be adjusted?

@FlatheadGarage 4 жыл бұрын

I heard rattling I'm not new to working on quad I was going to adjust the timing chain but I figured before I order a timing chain adjuster id just go ahead and adjust the valves.

@ryanmicklo1616 4 жыл бұрын

@@FlatheadGarage Ok, thank you!

@Scott00 Жыл бұрын

Old video so i may not get a reply.. but does it have to be at TDC on compression stroke before making this adjustment?

@captaindeadpool1640 Жыл бұрын

Yes, always make sure it's TDC. Turn the crank counter clockwise there is a line on the case and 2 lines on the inside. You want to be in the middle of those 2 lines like it shows in the video.

@sparkplug9750 4 жыл бұрын

Still sounds like it’s making noise

@tristankemplin6766 4 жыл бұрын

I dont know if that for all tho

@seanmarchiny 4 жыл бұрын

Back the nuts off so you can grip the tension bolt better

@MrLTW2009 3 жыл бұрын

Damn I was panicking about this

@FlatheadGarage 3 жыл бұрын

@the_official_colaberation7856 2 жыл бұрын

My 400ex is making a really bad ticking noise and it's definitely the valves they go ping ping ping ping

@ejbingusreactions 3 жыл бұрын

What's up bro I got a channel kind of like yours you should holler at me man thanks for the good video hopefully you like some of my stuff, and let me know that you jumped on their preciate it man thanks for the advice