thanks so much mate!

Its impossible in bravo 2 to tint side Windows without taking out Window from door 😓

your very welcome. how is it going? need more help?

@@ryanbrilliant6793 yeah I messed it up 😒 it all went well except one of the corners wouldn't tuck in to both sides at the same time and it ended up creasing and not sticking down. But 3 of the windows were OK I still need to do the back 1. I bought ready cut tint so now I need to buy a roll to replace the 1 window. But I managed to get the fingers out by using this video. I guess i just need more practice. But thanks 😁

You all prolly dont care at all but does anybody know a way to log back into an instagram account?? I was stupid lost the login password. I would love any tips you can give me

@Nicolas Achilles instablaster ;)

@Hezekiah Abdiel I really appreciate your reply. I found the site thru google and im waiting for the hacking stuff atm. Takes a while so I will reply here later with my results.

@Hezekiah Abdiel it did the trick and I finally got access to my account again. I'm so happy:D Thanks so much, you saved my account!

@Nicolas Achilles No problem :D

hi great to know. how can I help further? anything your struggling with?

@@ryanbrilliant6793 no brother! Now practicing on my mates cars..😅

How did it go

hey bro thanks so much for the positive comment. how did you get on? I can help you furthermore? thanks

@@ryanbrilliant6793 Fully flopped lol. Took the roll outside. A gust of wind came and creased the whole roll 😂 Tried cutting the film against the rubber seals but ended up with a fully jagged edge. I've done all sorts of mechanical, electrical and paint jobs but I think tinting just ain't for me 😂 I may try again when I have some free time

@@salimsheikh2580 haha I fuck everything hopefully this not going to be the case with this

@@Prince-yw4lk Good luck broski!

hey how did it go?

@@ryanbrilliant6793 sort of ok. Side widows was spot on, but the rear tailgate window, not so good

how did you get on? am going do mine tomorrow..

@@boblad77 got on fine apart from the door part. The rear did not shrink as well as I wanted. Be patient. I was hurrying it a bit. Turned out alright though.

Mate this it full of bullshit you would never cut on the glass like that in case you damaged the glass

Dan Davidson mate are you thicker than glass itself. Bro you always cut on the glass just don’t dig the knife in and you won’t scratch it. How else are you going to cut the tint to shape without being a bell end and wasting excess time

Will be trying that

use a heat gun to heat the outside whilst pushing the bubbles back down. eventually they will stick. unless there to big and if so that means you did heat shrink sufficiently

It all depends on the shape of the glass

It’s limo tint, 5% light

yes

no it won't shrink

yeap! you can try Llumar ATC. it is much better.

Did you see my last video? Could help you cut all so.

No bro, you ain’t got it right. You need to use a glove on very curvy windows else the card isn’t flexible and it will crease the tint as you push down on the fingers

Im done with that. Still doesnt look acceptable and i dont want to roll my windows down. After about 5 rolls i came to the conclusion that film really matters. At first i thought im just making mistakes, but cheap chinese stuff is really thin, you can shrink only tiny fingers, if you handle it like the dude in this video you're getting nowhere. It scratches very easily when pushing out the solution, even when using a soft squeege and lubricating the surface. Need to get my hands on some proper film, problem is, nobody sells it in my area, only tint shops have it since they buy in bulk. If you can get your hands on something like genuine 3M( a lot of fakes out there) stuff then by all means try it, if its the shenzen special "solarwindowfilm" then dont bother, you'll wreck your nerves. Honestly you get what you pay for.

probably just condensation so should go

Yes mate this is me. Use Suntek tint. You can buy it from mdpsupplies.co.uk. Problem with the cheaper tint is that it won’t heat shrink and it makes the job a lot harder because it is such bad quality

It doesn't

no its much easier to do it on the outside because the film is thicker as u haven't removed the outer protective layer and also more space to work around

@@ryanbrilliant6793 Got it. Thanks for the reply!

Yes it will but will take longer

Head and shoulders

Sky's the limit!

Not not hot enough, tried with a crap heat gun and did not work

If it's carbon based then yes. The other/cheap stuff will fade in the sun as it's coloured using dye.

You do kniw tint has a grain and can only be heat shaped 1 way

Make sure that you are using 2 ply film other wise you'll burn it every time

​@@mguerrero8787 it's 4 year late but anyway yeah you're right. I remember that everytime I try to heat the cheap 1 ply tint it burned the very second I turn the heat gun on it.