HOW TO USE A VALVE SPRING TESTER

Рет қаралды 7,944

2 жыл бұрын

HOW TO USE A VALVE SPRING TESTER. Once in a while, I get a suggestion for a video that I just have to do. This is one of those videos. In this video, I will show you tips and tricks for how to use a valve spring tester correctly. I have years of experience and some tools I have fabricated myself that i will use to teach you the importance of and the correct way to test valve springs on a valve spring tester.
As always, I appreciate your feedback and suggestions, I welcome your comments and ask you to like and subscribe this video and this channel. You can also hit the notification button, so you always know when I have something else to share.

Пікірлер: 25

@johntarsa3248 Ай бұрын

nice demonstration, thank you for sharing. I learned me somtin today.😬

@Mark_Linford 2 жыл бұрын

You are an excellent teacher Daniel .

@MrDanielSoliz 2 жыл бұрын

Thank you.

@cdpperformance2613 Жыл бұрын

@@MrDanielSoliz i purchased one of the Rimac big blue valve spring testers it’s rated at 350Lb do you know if I can start with it on doing small Block engines? Stock to mild build?

@cdpperformance2613 Жыл бұрын

@@MrDanielSoliz quick question I’m New to doing all this machine shop Work trying to learn it but do you have are can you do a video showing how to properly setup and read a dail bore gauge ?

@MrDanielSoliz Жыл бұрын

@@cdpperformance2613 will do! ✌️

@charles_wipman 2 жыл бұрын

Perfectly explained, also shown that the spring testers need a calibration spring, that i bet that not everyone has used or have.

@RaysLaughsAndLyrics 2 жыл бұрын

Thanks Dan.. I now have the perfect tool to tune my Competition PoGo Stick for peak performance... 👍Have a great weekend

@danielsmith-ze3wy 2 жыл бұрын

Thanks for the video

@abdool1972 2 жыл бұрын

Trying to imagine all the engines out there with wonky spring pressure - ready to explode.

@jamiegroves1761 2 жыл бұрын

Thanks Danny 😎🍺👍🇦🇺

@nickkiofetzis5667 8 ай бұрын

nice stuff Danny thank's for the knowledge.

@aroundlinemen 2 жыл бұрын

Great video, thanks for sharing 🇺🇸🏁

@MatthewScott 2 жыл бұрын

keep it up. I own a small shop in new Braunfels. good to see locals on here.

@MrDanielSoliz 2 жыл бұрын

Thank You

@wademiyataki9221 2 жыл бұрын

You call Shop Mom and ask how much for the Daniel Soliz custom spring tester.😁

@EJProMods 2 жыл бұрын

Great video as always. any tips how to measure valve spring height on import heads that have small diameter springs and are deep in hole so there are no room for regular spring height micrometer or snap gauge ? I have made custom tool for that, but its not very accurate.

@MrDanielSoliz 2 жыл бұрын

No tip there, that’s always I hard one to figure out.

@steelblackface Жыл бұрын

I rebuilt my Duramax motor and after a few days of driving one of my rocker bridge got dislodge. I reinstalled it and set the valve lash and it again. I suspect that I might have a bad spring. Any thought. Will a floating valve cause this? I didnot check the springs and I reused them. My motor has over 300k miles on it.

@MrDanielSoliz Жыл бұрын

Was anything just done live a valve job or mill?

@steelblackface Жыл бұрын

@@MrDanielSoliz no nothing of that sort. The valves were removed and we're hand lapped with grinding compound. No machinery was used.

@danielsmith-ze3wy 2 жыл бұрын

My dad would say your cars and motor are just like your women you abuse either one they will leave you on the side of the road . And if your buddy takes either one out and throws a rod in em one you gonna be pissed

@MrDanielSoliz 2 жыл бұрын

🤣🤣🤣🤣

@ronaldjohnson1474 2 жыл бұрын

Today's youth expect tools to be an "end all" for them. They have completely forgotten that tools are an extension of personal skills. IE: how do you break a socket?