How to use your Air Lift 3P/3H Controller

Рет қаралды 104,410

Күн бұрын

Today's video will cover all the details of setting up and using your Air Lift 3P/3H Controller, from presets, to compressor cycle, to rise on start! As always if you have any questions leave them down in the comments below!
Contents of this video:
0:00 - intro
0:15 - air lift controller button layout
0:33 - how to calibrate
1:01 - how to change compressor settings
1:39 - Rise on start
1:58 - minimum driving height
2:06 - How to swap from pressure to height based read out for 3H systems
2:18 - All up and all down buttons
2:59 - how to change pressure unit
3:20 - air lift presets and how to set them
4:01 - how to make a preset on your air lift controller
4:41 - outro
-----
Your One Stop Drop Shop since 2009
www.bagriders.com/
-----
Shop Merch: bit.ly/2T0q67V
-----
Follow us on social media!
Instagram: / . .
Facebook: / . .
-----

Пікірлер: 146

@luismendoza9049 10 ай бұрын

So much useful info thank you for this simple and straight to the point

@asadrizvi3678 10 ай бұрын

Look nice and like your video bro...I never done this before but I m learning..

@josevidal9250 2 жыл бұрын

Can you make a video like this one but for manual air ride kit please.

@bagriders 2 жыл бұрын

The manual system just uses paddle valves, it's a simple switch with up for up and down for down!

@bleedzacid 2 жыл бұрын

I get mine next week starting to get nervous. Hope I didn’t screw up my Lex

@bagriders 2 жыл бұрын

Just give us a call if you have any questions!

@lolobon1331 2 жыл бұрын

How can I disable the automatic lift because sometimes when I’m driving in my normal drive height for example 118 on the rear goes automatically to 125

@bagriders 2 жыл бұрын

Try the following! Turn off rise on start, preset maintain, begin a new calibration, and be sure your presets are set correctly.

@iron_toro Жыл бұрын

how do you find out what is the MAX psi you should set for your vehicle? Mine is 2020 supra widebody

@bagriders Жыл бұрын

To figure out max bag pressures you can check your suspension manual. For max tank pressure it doesn't matter what car you have you can set the PSI from 150-200PSI. If your suspension runs higher pressure a higher tank pressure will help!

@Joseb1998 2 жыл бұрын

There is a new airlift 3p controller update. The calibration is different. Can you guys make a video on it?

@bagriders 2 жыл бұрын

We sure can!

@thaieralawadh2223 2 жыл бұрын

@@bagriders could you please give good example to normal psi up and down to understand better? My car is a mustang but I think all car would be in the same range..

@bmw1211 2 жыл бұрын

Hellooo and thank you for your video but do you know if there is a manual in french please ?

@bagriders 2 жыл бұрын

We do not have a French specific manual but it most likely can be transcribed through your internet browser.

@jodyturpin7258 2 жыл бұрын

Show me 2016 air lift on 1 ton GMC

@briantelander2544 Жыл бұрын

How do you change minimum pressure when the compressor kicks on. Mine kicks on if pressure drops 15psi

@bagriders Жыл бұрын

You can't change the minimum pressure on the Air Lift 3P but you can change the maximum.

@mikecruz1106 2 жыл бұрын

How do I find out what our limit for our air tank? I have a focus st.

@bagriders 2 жыл бұрын

Check out website! We list the max pressure for each tank.

@xXKrYPT1CxShOXx 2 жыл бұрын

Just bought rs with airlift kit on it, not familiar with air bags at all. Is it normal for the front left and back right to be dumped after the car is off and been sitting like 20 minutes? The front right and back left are still at the presets when I get in but the front eft and back right have dumped. When I get in and turn it over the bags don't automatically inflate until I hit center button to air up to presets. Thank you

@bagriders 2 жыл бұрын

If the car is dumped after 20 minutes it sounds like there might be a leak. Double check your lines to make sure they are not kinked.

@roboparkour Жыл бұрын

Wondering if you could help I have a problem with my 3p manifold where I have everything wired in and the compressor turns on as it should I get 2 flashes on awake on the motherboard but the controller won’t turn on or connect to my phone and there is 12v going to the maifold, any help would be appreciated !!

@bagriders Жыл бұрын

Would you mind reaching out to our technical support team? You can contact them at sales@bagriders.com or call 844-404-7344.

@AshleyHernandez-jq7gu Жыл бұрын

Is it ok to leave my car Aired out overnight ? Or should I leave it at ride height/stock height ? Thanks !

@bagriders Жыл бұрын

Yes you can leave your car aired out overnight!

@illwill610 2 жыл бұрын

What is the "preset maintain" option? Can you explain please? And what should it be set to.

@bagriders 2 жыл бұрын

Preset maintain does exactly what it says! It tries to "maintain" the preset you are at while driving, can be helpful if you have small leaks, or just want to make sure no matter what your preset is maintained.

@illwill610 2 жыл бұрын

@@bagriders another question...I have noticed it takes less air to maintain on the right side of the car then the left...ex: 60 54 front and 60-53 rear...but when I set my ride height preset to these numbers, it doesn't air up to them, instead it does over the set amount and ends up evening it out...ex: 60 all around...do u know why this would be?

@illwill610 Жыл бұрын

@@NearMedia got mine fixed 11 months ago lol. Everything sits the same now

@illwill610 Жыл бұрын

@@NearMedia took it back to the installer and he made adjustments. Idk what exactly but now my numbers are even all around.

@769707 11 ай бұрын

If I buy the 3p kit now, can I update to the 3h later? and do you have the link for that? thanks

@bagriders 11 ай бұрын

Yes, you can add the additional wiring and height sensors any time, if you feel you.need them.

@kannikayaemtrat325 2 жыл бұрын

What is the ecu not found mean? is just Start doing that on my controller and is won't shut off. Please help me

@bagriders 2 жыл бұрын

Hey! Please email tech@bagriders.com and one of our support staff can help diagnose with you!

@vescou Жыл бұрын

how to set the minimum low high to not be 0, because i already broke my fenders by accidentally hit it to the down button? + Can it be set on the shocks to never go that low again ? .. I just bought a car equipped with same suspension. The Car is Audi A5 Sportback - I like it, but this All-Down button is a problem to me.. The car looks strange on all high - front is a lot higher than back of the car, is there any correction on that?

@bagriders Жыл бұрын

Yes in the settings menu under 'operation' then minimum drive height/pressure you can make that adjustment.

@nycyabber7103 11 ай бұрын

You mention vehicles needing specific pressure in the bags when changing the compressor settings. How do you know what pressure a specific car needs?

@bagriders 11 ай бұрын

Great question! Cars running over 80PSI or sleeve bags we recommend running 200PSI in the tank. Feel free to call in at 844-404-7344 and we can help suggest whats right for your car.

@handsomelildevil Жыл бұрын

Can you do a video on how to properly drain the tank? Would really appreciate it! Keep it up with these helpful videos.

@bagriders Жыл бұрын

Great suggestion, we sure can! Always feel free to call or email our customer support team to walk you through the steps in the mean time.

@Kaise._ Жыл бұрын

Also I set my low height as my preset but on rise on start it still airs up higher then what I set it to

@bagriders Жыл бұрын

How much higher is it going? We would love to help you solve this issue. Could you send our customer service team a video? You can email it to sales@bagriders.com.

@Kaise._ Жыл бұрын

@@bagriders just emailed you guys thank you

@RWarrior777 2 жыл бұрын

I have black toyota camry 2015. Interested in purchasing this system. Where can I purchase ?. Do they offer payment plan. Thanks

@bagriders 2 жыл бұрын

Hey! For a quote on a kit you can either use the vehicle selector on our website, or email sales@bagriders.com!

@392horseplay2 3 жыл бұрын

I can’t set my air out preset anymore since the last update. I don’t like it on all 0’s and had my rear psi set on 50 to air out before the update. Is there something different we have to do now to set air out preset?

@TehAnalog 3 жыл бұрын

"air out" is used to go to 0 all around. In settings, you need to select the "preset" option instead of "air out". This will allow you to set your lowest setting which would be your Air'd out setting.

@bagriders 3 жыл бұрын

What he said! Use the "all down" button and set it as a preset to 50psi instead of using it as just an air out button

@darren.a.b7400 3 жыл бұрын

What about duty cycle?

@bagriders 3 жыл бұрын

We'll have a video dedicated to duty cycle, but you can always check the product page for your specific compressor to see what the recommended duty cycle is!

@cosmanonel Жыл бұрын

Hello. can the remote control be unlocked while driving?

@bagriders Жыл бұрын

It can! You will want to turn off the setting called "Stance Guard." Checkout our other video called 'How To Disable "Stance Guard" For Air Lift Performance 3P/3H.'

@stianSKII 2 жыл бұрын

when i use my "speedbump" button and press back to rideheight, it goes lower then my rideheight (almost airout the bags) and them fills it back up to rideheight. any way to fix that?

@bagriders 2 жыл бұрын

Are you on 3P or 3H?

@stianSKII 2 жыл бұрын

@@bagriders 3P, but i did calibrate again and seems fine now!

@rockbrothers8546 4 ай бұрын

What’s the speed bump button

@gabeinusa152 Жыл бұрын

Ok so if I set up my camaro they way I want i mean how low i want it I just leave the button press to save it? Or its ok if I don't save it ? I low my car the other days and I forgot to save the high is a problem or is just fine if I don't save?

@bagriders Жыл бұрын

It's okay to not save your presets but we highly recommend saving them as its a great feature of the system!

@kendoug5722 Жыл бұрын

Can i use a manual switch controller on 3p?

@bagriders Жыл бұрын

The only controller that connects to the Air Lift 3P System is the controller it comes with or a wireless device such as a cellphone. You can manually adjust each corner on each device.

@ballsinyourmouth2000 3 жыл бұрын

Do we have to install a watertrap and how often should we drain the tank?

@bagriders 3 жыл бұрын

You need a water trap to properly drain your system, you should be draining it every 1-2 weeks depending on how much you use the system!

@thaieralawadh2223 2 жыл бұрын

@@bagriders could you please make a video about draining and regular maintenance to keep the equipment in best shape ? Best practices and not to do things as well.. Many thanks 🥰

@DDGFlacko Жыл бұрын

@@bagriders is it bad if I drain it more often than normal?

@bagriders Жыл бұрын

No! The more you drain it, the better.

@Neekp10 Жыл бұрын

How can you set your system up to air up automatically when you start your car?

@bagriders Жыл бұрын

You want to head into the settings and change the 'rise on start' mode to on. It will the air up every time you turn the ignition on.

@moncefjarfi1459 4 ай бұрын

Hello I have Volkswagen t5 and I don’t what is the right size to put?

@bagriders 4 ай бұрын

We would recommend running 3/8" air line as the vehicle weighs over 4000lbs.

@simplyblazeegaming 2 жыл бұрын

i cant seem to update mine for some reason. it wont connect to bluetooth

@bagriders 2 жыл бұрын

Feel free to reach out to our support team. Email sales@bagriders.com or call 844-404-7344

@wake777 Жыл бұрын

my controller for my 3p recently kept rebooting itself, and then eventually doesnt show anything in the screen. whats the potential fix for this?

@bagriders Жыл бұрын

If the controller doesn't want to stay on check your power and ground cable. If its not that check your ignition wire and make sure it's getting 12v. If that doesn't solve the rebooting issue feel free to give us a call at 844-404-7344 or email our support team at tech@bagriders.com.

@user-uu1qe5lb6y Жыл бұрын

Could be a fuse

@DennisW95 2 жыл бұрын

I lost my controller. Is it possible to put the car without the controller up ?

@bagriders 2 жыл бұрын

You can use the bluetooth function on Air Lift or Accuair systems to raise the car!

@dereknguyen6818 2 жыл бұрын

How do you press the button? I double tap it and it doesn’t work sometimes. Do you have to do it slow or what? Just got mine on a few days ago still trying to figure out how to use it properly

@bagriders 2 жыл бұрын

Be sure to calibrate the system first! The individual bag buttons are a one press and the preset buttons down the middle take two presses.

@dereknguyen6818 2 жыл бұрын

@@bagriders it’s calibrated. I have the 3p and the remote I see a little lock on top sometimes I assume the remote is locked and won’t do anything how do I unlock it?

@bagriders Жыл бұрын

That lock is the stance guard feature. We have a video on our page talking about what exactly that is.

@aggelosgiannopoulos6812 Жыл бұрын

when we turn off the car engine, the pressure drops. What should I do ;

@bagriders Жыл бұрын

Could you send us a video? Our support team can help you figure this out. Please email the video to sales@bagriders.com.

@waynek7190 Жыл бұрын

what about Anti Cross-Load? what does it do?

@bagriders Жыл бұрын

The Anti-Cross Loading + Axle Equalization mode allows the system to consider both height and pressure measures together, to achieve the right height at the right pressure.

@demineon4966 5 ай бұрын

Just installed mine 1 of my rear bags won’t hold psi like the other 3 :( and my controller doesn’t hold the psi I preset is that normal to fluctuate?

@bagriders 5 ай бұрын

It sounds like one of your bags has a leak! Checkout our other video "How to Find and Fix an Air Ride Leak."

@1nonly510 2 жыл бұрын

Hi there just have a question, when I made the preset for my low ride height, everything airs, however my pre set was set to 25, my left airbag just goes all the way down to 0 and then shoots back up to 25, is there any solution to this that I’m not understanding

@bagriders 2 жыл бұрын

You can contact our customer support team for help! Call 844-404-7344 or email sales@bagriders.com

@dionleblanc4962 Жыл бұрын

how do you know what is recommended

@bagriders Жыл бұрын

Give us a call or email you can we can help! Our email is sales@bagriders.com and our phone is 844-404-7344.

@worxm9411 11 ай бұрын

I can't lift while driving, can this be changed?

@bagriders 11 ай бұрын

If you have the Air Lift 3P or 3H, you might also have "Stance Guard" enabled. Check out our other video on how to turn it off so you can adjust your air suspension while driving! kzfaq.info/get/bejne/etN3q9t_v9Depmw.html

@realone8173 9 ай бұрын

How do i keep it at the setting height? Seems after it sits over a little bit rear sags and front keeps height? Pls help

@bagriders 9 ай бұрын

Try turning on the preset maintain function found in the setting.

@realone8173 9 ай бұрын

@@bagriders thank u ill try that

@jjnapier4190 7 ай бұрын

Is there not a rear up/down like the front?

@bagriders 7 ай бұрын

There is not. You would have to air the rear up and down by using a preset or by each corner manually.

@jayu3948 Жыл бұрын

I was told when you’re aired out, and it’s time to drive the car, you should air up all bags to over 100psi to open up the bags, then lower to ride height. True?

@bagriders Жыл бұрын

You don't have to do that! The digital systems nowadays will automatically hit your desired preset.

@angelflores1739 Жыл бұрын

My controller keeps turning on and off, anyone know a solution for this ?

@bagriders Жыл бұрын

Check the controller connection on the USB cable. Next step would be to make sure your ignition wire is getting a constant 12v.

@boyishdog123 Ай бұрын

How do you know what psi to run on the top right corner of the remote?

@bagriders Ай бұрын

In your tank?

@boyishdog123 Ай бұрын

@@bagriders yes!

@boyishdog123 Ай бұрын

Like what should give you a reason to increase the PSI? Whats the starting level you should etc

@AyekevZ Жыл бұрын

What’s better 3P or 3H??

@bagriders Жыл бұрын

3P is a pressure based system whereas 3H is a height based system. The 3H is going to take a little more time to install but is going to be more accurate when hitting its presets.

@jaysonhobo9767 Жыл бұрын

How do I callibrate my system when I can’t physically air out all the way, due to my wheels being to wide, installed my air ride and now my stock wheels and my aftermarket wheels don’t fit without spacers, and now they will hit my arches if I air out all the way, ik know I just will have to buy new wheels but I need to be able to drive my car in the meantime.

@bagriders Жыл бұрын

There are a few options here. Spacers would be a cheap and easy route but the management also allows you to set minimum and maximum pressure during the calibration process. This will help prevent you from airing all the way out but still allowing the system to calibrate to use your presets.

@Tesla9595 9 ай бұрын

Yes but for model it’s not available u need buy airmatic suspension in order to fix this

@bagriders 9 ай бұрын

Correct this is controller is designed to be paired with an aftermarket air suspension.

@uofa 2 жыл бұрын

I set my rise on start to on but when I get in car after airing out it doesn’t owek

@bagriders 2 жыл бұрын

Have you tried recalibrating your system?

@user-cc1vu9sy6c 10 ай бұрын

is my air ride supposed to be very bumpy ride?

@bagriders 10 ай бұрын

Air ride suspension systems are designed to provide a smoother and more comfortable ride compared to traditional coil spring suspensions. If you're experiencing a bumpy ride we recommend comparing your ride pressures to the manufacture specifications.

@daghanam 3 ай бұрын

I have a question fellow low riders ! I have 3p system but for some reason when i start the car and open the app , bluetooth gets connected no problem but as soon as i leave the app and go to different app , when i come back to 3p app , i doesn’t get connected anymore until i turn off the car and start it again . Appreciate any help 🙏🏼🙏🏼🙏🏼

@bagriders 3 ай бұрын

Great question! Do you have any other bluetooth devices in the car such as car play? When going to a different app the 3P bluetooth recognizes you are no longer using it disabling it. You can reconnect it again without having to shut the system down by accessing the menu and reenabling bluetooth in the 3P settings. Also be sure to keep you 3P up to date as new software is always being pushed.

@daghanam 3 ай бұрын

@@bagriders Thanks for writing back to me I tried to reconnect by enabling bluetooth but didn’t work , even on my phone while it says not connected, i went to setting and tried to reconnect through manifold , sometimes works and sometimes dont !!!

@bagriders 3 ай бұрын

@@daghanam If that didn''t work try giving our customer support team a call at 844-404-7344 or email tech@bagriders.com

@daghanam 3 ай бұрын

@@bagriders awesome Thanks for your help

@XalvaroramosX 2 жыл бұрын

⭐️⭐️⭐️⭐️⭐️

@vescou Жыл бұрын

when im not using the car, is it ok to leave it on maximum hight ?

@bagriders Жыл бұрын

Yes it's best practice to leave it at ride height or all the way aired up!

@Kaise._ Жыл бұрын

Wait so how do y’all air out I’m confused ?

@bagriders Жыл бұрын

To air out you want to use the middle bottom button.

@Kaise._ Жыл бұрын

@@bagriders but I thought that was your low ride height ?

@bagriders Жыл бұрын

@@Kaise._ You have 5 customizable presets with the 3P/H controller. Starting from the top we most commonly see users set them to momentarily all up, high drive height preset, normal drive height preset, low drive height preset, and the very bottom button all down/air out button.

@leoortiz661 2 жыл бұрын

Does this have air out on off?

@bagriders 2 жыл бұрын

Yes you are able to air out with the controller.

@leoortiz661 2 жыл бұрын

@@bagriders I meant air out when you turn the car off

@bagriders Жыл бұрын

You cannot air out the car when it's off. A properly wired system turns on when the car turns on and turns off when the car turns off. You can use the show mode on the system to deactivate the compressors while leaving the key in the ignition.

@TRICKYBYRD 2 жыл бұрын

Anyone know why I get the loud clunk sound almost feels like I'm riding on plates when I hit bumps when I'm anything below 120psi up front. I bought it with it already bagged all the bags under the good and it rides great when I'm riding skyjacker status it looks good aired out but I can't ride around anywhere close to what I want to be riding around and what I should be writing at does it have anything to do with the dampening system because I think the guy that installed himself I don't think anybody was doing. It's just a loud clunk and feel that I get on every bump more so in the front and it's not anything to do with the factory stuff it's definitely the bags but basically when I'm under 120 or closer to 1:15 it's almost as if there's no air in the bags whatsoever but there is for sure. And this is for a Infinity Q50 2017

@bagriders 2 жыл бұрын

Great question! Could you contact our customer service team at sales@bagriders.com or call 844-404-7344. It sounds like your strut is bottoming out or maxing out. We would be more than happy to recommend some pressures to help prevent this.

@Tht_1sti Жыл бұрын

I had the same issue, spin the damper knob off and then put an Allen in the whole and use a wrench to tighten the bolt on top of the strut