Thank you!

that's why you need a relay it will stop the problem of draining your batteries power

demonllama95 a relay does not have anything to do with power consumption... To be clear: A relay is so that you arnt piggybacking off of another closed circuit. If the factory designed there to be two headlights and two taillights on one circuit then putting a 700 watt light bar on it might overload that circuit system.. That however is NOT what he is talking about. With car electrical systems

@@chanelhart1239 Keep in mind that a relay is basically just a switch to open or close the circuit. They are used so you dont have to run thick power cables back and forth from source to a switch on the dash and back etc. You connect the thick power cable to relay in engine bay and then much smaller trigger cables to and from the switch on the dash. Those trigger wires only send the signal to relay to open or close the circuit (hence turning off or on). You can also have the relays programmed to pulse, just just your blinkers do. The stalk on steering column are the small trigger wires that activate the blinking relay which is connected to the lights...

@@-Awareness thank you

so you can have the highbeams on without the lightbar being on

And it's required by law

@@andrewchippendale2333 ...but you cant have your light bar lit without your high beams on which defeats the purpose of being off road.. light bars are brighter than head lights so you can use them on dipped beam so its a load of crap..

@@chrisfi3d yeah sods law when you think about it

Hi Paulandloz1, Our harness is designed for the H4 globe found in a lot of cars, if you have something different, you'll need to splice (wire tap connector) into the headlight high beam wires and adapt the wiring harness to suit or if you're not sure, I'd recommend for you to contact your local auto electrician about it. I hope this helps.

Hey Israel, Thanks for your question. Check with your local state laws to clarify this. Most states in Australia require light bars only to be activated when the high beams are switched on. That way you only have one switch to turn off both high beams and light bar at the same time. - Ash

Where can one buy the head light harness from...? If your in australia does the shop post over seas on orders ?

As super jeep auto says check your country laws i wired two light bars up to battery relays and switch all correctly.but jeep failed mot because they were not wired through head light circuit..i presented my case that i only use the light bars off road and would not use head lights as the bars combind gave me 400watts and 24000 lumens at 5k white light making head lights look like candle so use them on low 1beams so when i turn them off i have low beams but they said no way fail. So since my last comment ha e head light adaptor harness removed and replaced bumper mounted light bar for two smaller 74 watt 7,200 lumen 5k bright white combo spot and floods through my head lights which i will use on and off road sod them mot ppl. And magnet mount the roof bar when i need it with to battery etc harness in place when i want the bigger light. In short check your country laws or make sure you can remove lights when car is mot or nct depending on your country..

HI NextDoorDigital - Sure, will have to use a 12v battery source, not 240v though! hope this helps!

Why don’t you buy an led strip from Home Depot?

If your mower has lights already splice the light bar wires into the wires for the headlights on the mower and just put the harness in your shed or something as you wont be using it at all.

Yep red to red, black to black

Hi Errol, Possibly but generally cigarette wiring is fused at 10 amps and has thin wires to suit up to 10 amps. I'd recommend wiring it separately with a fuse.

It had a light receptor in the switch that can be preset,to you specs, at any parts dealers hat has a napquan light bar programmer.

Thanks! :D

Hi William, Thanks for your questions. Yes, a rocker switch can be used in it's place. This kit is designed for positive earthed vehicles only, Negatively earthed vehicles require modifying the piggy back adaptors. Discuss with your local automotive electrician to do this for you if you’re not sure how to do this. - Ash

G'day William. Did you manage to replace the switch? What type of rocker did you end up with?

shao rocky still I can't find the actual item, send me a direct link pls, I don'twant to get the wrong item.. Thanks

Hi Vhon, Thanks for your question. You can find this SCA lightbar wiring harness on our website bit.ly/2yjsga2 - Ash

yes but its illegal to drive on the road with a light bar turned on

For legality issues in AUS/NZ you need to have the switch mounted inside the cab. Thanks

​@@supercheapautotv what about under the bonnet, save running switch into cab ?

double sided tape probably

Yep! Double sided tape - easy as!

Hi Danny, could be a number of different issues, are you able to email us all your details of your car etc to reece.moger@superretailgroup.com, we'll pass it on to our tech team to look into. Thanks Reece

Which country are you in..did you get your light bar working two years on ?....... dont bother answering i got my headlight adaptor kit and now have my light bars wirking through high beams..

Hi Matthew Moodley, the harness is universal and should fit on any car. Thanks, Reece :)

+Supercheap Auto cheers

ken neth they have a wiring diagram on the website that you purchase it thru.. it’s in the video description