How to wire a STEPPER motor and CONTROLLER

Рет қаралды 77,565

Күн бұрын

#howto #steppermotor #electronic
In this video I will walk you through How to wire a stepper motor and controller up. Stepper motors are great, they are small torquey motors that have a lot of controllable functions.
Hopefully by the end of this video you'll have your stepper motor and controller all wired up and working
Stepper motor- RTELLIGENT Nema 23 Stepper Motor 3.0Nm/425oz.in 4-lead 57x57x100mm 8mm Shaft High Torque Step Motor CNC Mill Lathe Router www.amazon.co.uk/dp/B07V9RMWM...
Stepper motor Controller- CNC Digital Microstep driver DM542 Stepper Motor Driver Controller 2-phase 20-50V DC Max 4.2A 42 57 86 Motor Driver for Nema 17, 23 and Nema 34 series stepper motor, Replace M542 M542H www.amazon.co.uk/dp/B08GCFNQF...
Stepper motor pulse generator- www.ebay.co.uk/itm/203321060298
24v DC 10A power supply unit- www.ebay.co.uk/itm/143870746897
If this video has helped then please subscribe to the channel also
/ machiningwithjoe

Пікірлер: 63

@ecirpnai1 3 жыл бұрын

Thanks Joe for another excellent video.

@HealEasyNow 2 ай бұрын

Excellent detailing. all the best and be blessed..

@pradeepramuk Жыл бұрын

Pretty well Explained. Thank you.

@feefifofum 2 жыл бұрын

lagging behind, but where you go , we follow😀. I got my stepper motor today and the controller and pulse modulator - your video is soo useful to get the things connected up without doing a degree...much appreciated chap

@MachiningwithJoe 2 жыл бұрын

Really glad the video has helped you out it’s a great upgrade well worth it. All the best.

@j3xk72r9 3 жыл бұрын

I would fit an on/off switch on the mains input together with a correctly sized input fuse and a LED pilot lamp driven from the 24V line to remind you that it is on.

@MachiningwithJoe 3 жыл бұрын

Thank you for the advise Horus great input 👍

@brenwyattm0rij909 3 жыл бұрын

Spot on Joe! Keep um coming Mate!

@MachiningwithJoe 3 жыл бұрын

Will do cheers 👍

@matthubbard8541 3 жыл бұрын

Nice one Joe, good to see your channel followers growing in number, keep posting.

@MachiningwithJoe 3 жыл бұрын

Thanks Matt. Yeah numbers growing slowly and I’ll carry on making videos to hopefully help you guys out.

@crashpilot1 3 жыл бұрын

Nice one matey thank you very much

@Festivejelly 8 ай бұрын

I ended up installing the Nano ELS. Its quite handy in that it essentially turns the lathe into a CNC of sorts.

@MARIOista Жыл бұрын

Thank you ..That's a nice video easy to grasp it .

@MachiningwithJoe Жыл бұрын

Glad it made sense to you.

@Bianchi77 Жыл бұрын

Nice video, thanks for sharing :)

@Tehnarok Жыл бұрын

Thank you !

@iamnemo8479 3 жыл бұрын

New video, gets a automatic like 😎👍

@MachiningwithJoe 3 жыл бұрын

Thank you glad you enjoyed it.

@iamnemo8479 3 жыл бұрын

@@MachiningwithJoe always enjoy the content, helps get the workshop more efficient 😎👍

@MachiningwithJoe 3 жыл бұрын

Thank you again. Glad my videos are helping people out as well as allowing me to learn new skills. 👍

@iamnemo8479 3 жыл бұрын

@@MachiningwithJoe helping people learn how to make there workshops more efficient with things that they didn't know or know how to solve helps everyone , that helps everyone grow and give insights on how to upgrade and tailor for what they need😎, it definitely has for me, many thanks for that, much appreciated 🙂👍🙏

@niksechtniks Жыл бұрын

Very helpful Thanks!

@MachiningwithJoe Жыл бұрын

Your welcome

@glenlivingstonegl 7 ай бұрын

As a complete novice to this subject this explained so much i have 3 stepper motors that came off the mill originally it was set up as a CNC mill but its an older sherline knock off and i couldnt find the program to run it and i wanted a manual machine,i am looking to connect up two of the stepper motors as a power feed for 'Z' and 'Y' axis

@peteatkinson7884 10 ай бұрын

Nice one Joe, very clearly explained.

@MachiningwithJoe 10 ай бұрын

Thank you Pete glad you enjoyed.

@getahunkifleeshetu2210 Ай бұрын

⅔@@MachiningwithJoe

@larryfilkins5596 2 ай бұрын

Very good video. My question is how do I wire another switch in to change direction of the motor? I want to use a DPDT center off 6 pole momentary switch to change the direction of the motor. The two wires that are connected to the center 2 posts of this switch are the ones that get reversed depending on which way you move switch. Which two wires would I hook to these center posts that would control the direction of the motor?

@DaveNorthWest 2 ай бұрын

Another quick way to check if the wires are a pair is if you hold two of them together and can spin the motor if the motor is tougher to turn when there touching. Saves having to bust out the ohm meter

@kelvenguard 2 ай бұрын

THAT WORKS !!! I was thinking you were playing a JOKE and I was in for a SHOCK !!! BLUE-YELLOW and RED-GREEN holding these together was harder to turn the Motor :) Thanks

@stevenharris5063 6 ай бұрын

Awesome I need some help with a set up here

@Jestey6 2 жыл бұрын

Hi Joe. Good video, would have been nice to have seen the motor running, and as an additional comment, what happened to the white wire?🤔. One improvement would be to use an external changeover switch and potentiometer to control direction and speed, instead of cutting a hole in the box. I’m planning to fit an XYZ DRO to my new mill WM16B, and power the table and head lift . The thought is to use the same electronics i.e. PSU, PWM and Driver for both, and switch between the two stepper motors, and thoughts. Cheers Noel

@MachiningwithJoe 2 жыл бұрын

Hi ofrex if you check out my video on adding a power feed to the lathe you will see the motor in action. Do you mean the White wire coming from the motor ? If so because I used a connector plug between the motor and controller the wire colours differ end to end.

@geminiman2831 Жыл бұрын

What is the use of half current and full current? Currently I am using dm542 and nema 17! What pulse per revolution should I choose for nema17? And does more pulse means more speed?

@martincross4583 2 жыл бұрын

My only comment would be if there was a wiring diagram available. Trying to follow the video and the wiring is difficult. Other than that...excellent.

@AIJLarkin 3 жыл бұрын

Love those dewalt tool holders where did you get them from joe? Or were they 3d printed?

@MachiningwithJoe 3 жыл бұрын

They are 3D printed but not by me. I got them off eBay fairly cheap.

@zahidislam7630 2 жыл бұрын

Hi Joe. How are you bro. I installed the y axis stepper motor same as you have in my Cnc router 6090 machine but the problem is y axis direction changes traveling directions like when I use y+ machine moves forward and when I push y- it moves backward like both moves opposite direction and machine is also not going home correct

@billsmith5166 Жыл бұрын

Do you have a pulse generator that resets to zero when it's turned on so there's no surprise movement at start? How do you have the speed knob wired and where did you locate it? Is it possible to have a pulse spin dial connected at the same time a constant pulse generator is in the system? Have you tried using any switches wired to dip contacts? Any info or pointers to other specific videos would be GREATLY appreciated! Thanks for the video!

@drvnlp6269 2 жыл бұрын

How do you match up the power supply and motor? I see you're using a 10 amp ps to power the 4.2 amp motor. Thank you

@MachiningwithJoe 2 жыл бұрын

So from my knowledge the motor will only draw the current it’s rated to other than a bit more on start up. So I thought 10A was a safe number not to low and not to high to avoid extra cost

@tonyscott8257 3 жыл бұрын

Hi, I have only just found your channel. Could you let me know where you got the enclosure for the electrical components please.

@MachiningwithJoe 3 жыл бұрын

Hi Tony, First of all welcome to the channel hope you enjoy my content and find some of it useful. So the box I got from toolstation and here’s the link. www.toolstation.com/imo-stag-ip56-enclosure/p50968

@tomschmutz4179 Жыл бұрын

Thanks very much for this informative channel. Going to build the drive for my mill. Could you provide information on the controller on off switch. Thanks. Tom

@rahmanocawni5618 Жыл бұрын

Bonjour. Je vous souhaite de nous faire un vidéo pour mouver une table en longueur et largeur par deux motors. Thank you so much

@winandd8649 8 ай бұрын

@6:30 With "Pulses per revolution" you set microstepping., so the lower the number, the higher the speed and torque. The higher this number, the slower the motor turns, but has a more accurate position (also looses torque!) There is a lot to read about miscrostepping..

@MachiningwithJoe 8 ай бұрын

Thank you for your input I’ll have to read up on this some more as I’m wanting to use this setup for my mill now so would be good to set everything up for more torque.

@winandd8649 8 ай бұрын

@@MachiningwithJoe Cheers!

@elidari60 2 жыл бұрын

Hi why I cannot turn the hand crank on a lathe after I install the stepper motor thanks Eli

@MachiningwithJoe 2 жыл бұрын

The stepper motor is hard to turn even when powered off because of the opposing coils. You will have to slip the belt off to hand crank.

@mattivirta Жыл бұрын

cnc not need turn manual newer. keyboard have buttons can turn axis.

@mmpp1850 2 жыл бұрын

plz how can i controle dc motor with microstep motor i tried everything it works but i want to controlle it with two push buttons . i don't know why it works without them