Бейне

Рет қаралды 0

Пікірлер

@user-gd7kr3om7n Ай бұрын

Muchas gracias !!

@corvetteguy50 Ай бұрын

Thank you for your support! Glad to help! Vince

@durzoblint4847 4 ай бұрын

Thank you so much. Got the Masso Touch and the wiring diagrams are not always clear.

@corvetteguy50 4 ай бұрын

Thank you for your support. Glad to help. Thank you, Vince

@HirenPatel-zz5wu Ай бұрын

This is amazing. Thank you so much for taking the time to create this. I have that exact vfd and spindle have no idea which cables i need to buy. Can you help me? Which spec 4core shielded do i need as there's so many options. For vfd to masso is it 6 or 5 core and does it need to be shielded?

@corvetteguy50 Ай бұрын

Thank you for your support. You'll require my 20awg 5 lead DS Flexion ultra flex double shielded cable here.www.ebay.com/itm/133891673190 Just let me know the length you require, and I can custom cut it if this length is to long. 5 lead is required with a GX-16 6 pin connector as the 6th terminal is allocated to the shield drain of the cable for proper EMI dissipation. Thank you, Vince

@HirenPatel-zz5wu Ай бұрын

Will need approx 7.5m please. Thank you so much.

@corvetteguy50 Ай бұрын

Ok, please message me through my video's description to get your order in. Thank you, Vince

@andrefedorchuk4269 3 ай бұрын

Thank you for putting this info out. I have HY vfd 110v 2.2kw 3hp connected to Masso Touch. Set it up just as diagram shows, and my vfd /spindle works. My question is about speed of spindle. Masso Touch gives me ability to manually test spindle from MDI command, which is nice, but the problem is that when I tried to warm-up my spindle(I usually run it for 15min @10000rpms before I use it for cuts) by typing s10000 m3, my spindle revved up to 35000rpm(that's what my vfd was showing)! I've quickly stopped it with m5 command. So i tested with s3000, and it runs @9500rpm. S4000 gives me close to 16000 rpm. I know its the VFD settings, but I'm so new to this world of electronics, that looking into manual for answers is making me even more confused. I know its parameters that I need to look at, but which? Any help and pointing into right direction for answers would be greatly appreciated.

@corvetteguy50 3 ай бұрын

Thank you for your support, and kind words. I'm glad the video helped you. Masso should be directing you on how to get the PWM voltage corrected as this is what controls the speed. Please contact Masso as you purchased the controller from them, and they should be supporting what they sell. Thank you, Vince

@Z-add 2 ай бұрын

Do you have to oversize the vfd compared to the spindle wattage.

@corvetteguy50 2 ай бұрын

Thank you for your support. I've never seen a need to in real world testing. Some manufacturers claim the VFD should have higher output, but when asked for real world examples showing the actual difference it makes I've never seen any actual verifiable proof. All oversea VFD/spindle combinations work fine when matched with the same VFD output as the spindle they'll be matched with. Thank you, Vince

@richardvaio1 2 ай бұрын

I don’t normally comment but there drawing is an eletrical drawing. You wouldn’t add a busbar in that type of drawing. But I appreciate your helpful video as it’s been useful for me

@corvetteguy50 2 ай бұрын

Thank you for your support. Actually controller wiring diagrams is exactly where you would install a ground bus diagram as it lets end users understand its required to properly allocate shield drains to from their required double shielded cables. Thank you, Vince

@Luis-ul9cj 2 ай бұрын

Is it possible to reach out to you via phone for some information concerning the VFD?

@corvetteguy50 2 ай бұрын

Thank you for your support. Yes, I offer third party consultations for this. Please contact me through the video's description to schedule one. Thank you, Vince

@IceCreams62 4 ай бұрын

Hi. With single phase connection live and neutral can be connected indifferently to R S T terminals or there is a specific way ?

@corvetteguy50 4 ай бұрын

R connection is for Live, and T connection is for Neutral. This is the correct way to wire it. Thank you, Vince

@IceCreams62 4 ай бұрын

@@corvetteguy50 Thanks for the clarification Vince 😉

@corvetteguy50 4 ай бұрын

You bet...:) Thank you, Vince

@Z-add 2 ай бұрын

Do you get any requests for centroid acorn six boards

@corvetteguy50 2 ай бұрын

Thank you for your support. I don't as I'm not a vendor for Centroid. Thank you, Vince

@aticafloorable 4 ай бұрын

Mr. The frequency in the USA is 60 HZ AND THE FREQUENCY OF MY MOTOR IS 50 HZ. THE PARAMETERS P0.03 60HZ, PO.O4 60HZ, P0.06 60HZ, AND FOR THE MOTOR P2.02 50HZ Is this correct? my gt vfd is 5kw 7.5hp thanks

@corvetteguy50 4 ай бұрын

I answered this comment on another video you posted on. Thank you, Vince

@aticafloorable 4 ай бұрын

WHAT VALUE SHOULD THE EXTERNAL POTENTIOMETER HAVE, THANK YOU

@corvetteguy50 3 ай бұрын

Thank you for your support. Did you contact your vendor who sold the unit to you for support? Page 18 of the HY users manual covers it depending on your preference. Thank you, Vince