How to Wood Frame a Barndominium

No video

How to Wood Frame a Barndominium

Рет қаралды 38,012

The Barndo Channel - 1845 Barndominiums

Күн бұрын

Пікірлер: 43

@kellyb.7392 Жыл бұрын

Thank you!!! I have almost the same exact size house that we are building! This explains a lot!!

@user-sk1vn3gx8s 7 ай бұрын

I like this idea. 270-932-1829. Bj Lowe. Greensburg, KY. Do you build in this area

@eddiewilson8119 Жыл бұрын

Thank you for sharing this information!

@garretsmith7773 6 ай бұрын

Loved the video! I've been weighing the cost of metal exoskeleton or all wood barndo. Sturdi Lok by Look is a good product

@scentofapine 3 ай бұрын

One of the main reasons we chose steel building was to avoid wildfire damage. Spray foams are extremely inflammable. We used fiberglass and another layer of fiber glass in the interior wood structure!

@1845Barndo 29 күн бұрын

I think you might have some outdated information. Modern spray foam is not flammable at all. It meets all building codes regarding flame retardancy. We have even conducted our own tests to address certain concerns and have confirmed its safety.

@tonyaclapp2262 Жыл бұрын

I know you are in Texas, but do you build homes in other states?

@claudewiggins7404 Жыл бұрын

Thank you for the info.

@626dad Жыл бұрын

Love the channel 😁😁

@ryanamendala6524 Жыл бұрын

Great video. 12gauge code for all electrical? Noticed the can lights have 12 gauge wire as well.

@meisdetermined Жыл бұрын

Very interesting! Thank you for posting this. Curious about the perlin(?) that attaches the outside metal wall to the wood inside. So how is heat transfer stopped from going through the metal because the perlin is touching the outside metal? Or is there a slight transfer but it’s minimalized because there is spray foam above and beneath it?

@jasongrinnell1986 Жыл бұрын

You are talking such a slight thermal transfer compared to the stability of the internal structure. I’m not sure that there is a issue with it at all.

@meisdetermined Жыл бұрын

@@jasongrinnell1986 right I wasn’t sure either. That was why I asked. I just remember hearing that direct contact allows tranfer. Like a radiant barrier in a roof. But maybe with the insulation covering so much of the metal it slows it down a large enough percentage that it’s negligible??

@jhada3223 Жыл бұрын

Looks like quality work. Do you have any Hawaii connections? I'd love to have a Bardominium on Oahu.

@sociallydanjr2163 Ай бұрын

how is the horizontal 2x4 attached to the perlin? metal screw, ramset nail, nut/bolt.....?

@1845Barndo 29 күн бұрын

Ramset in most cases, all depending on the steel design. Rarely Screws, mostly ramset and nut/bolt

@MrMo0re24 9 ай бұрын

Why not spray foam before framing? Wouldn’t that make it easier?

@1845Barndo 8 ай бұрын

That is a personal choice for us, yes it would be easier, but we prefer to install all exterior penetrations before we foam, so we don't have to break the original foam envelope. Thanks for watching!

@jeromeblack7719 Жыл бұрын

in this video you mentioned --after the spray foam the structure would be climate controlled. how are you going to do that? does the hvac go throughout the metal structure?

@user-pj1fw3eu8v 8 ай бұрын

In the video, I believe you said that you would spray open cell foam to the back side of the r-panel. Did you mean to say closed cell foam? I would think that open cell would be like a wet sponge due to condensation.

@1845Barndo 8 ай бұрын

We do both, open and closed. Closed does provide a built in vapor barrier, but makes panel replacement almost impossible if it is ever needed. We use Tyvek at times to eliminate panel removal issues if we go that route. Thanks for watching.

@jerrydemars1989 Жыл бұрын

I'm curious I have a 40 x 54 existing pole barn considering converting to a barndominium slab was already poured but there is no stem wall would you have any suggestions

@NickKarpen Жыл бұрын

Curious why only 5 inches of open cell on your ceilings. I figured in TX you would want more than r19 in your ceilings.

@NaturalBeauty707 Жыл бұрын

is there Any possible way I can get one built in golden valley AZ...I done some research an there's no builders there for this particular home do your company build in other states or travel to build for your customers😁

@n8mike Жыл бұрын

You say you're gonna spray the ceiling? what happens if you get a really bad hailstorm and and the roof gets damaged the roof, how do you take the sheets of steel off when they are all spray foamed? you should put a plywood roof barrier down and then put some water Is barrier down, then metal roof on top so you can always replace the sheets when needed without harming the insulation.. Putting insulation right up to the sheets is absolutely dumb

@daktusdurggery5505 4 ай бұрын

Is it okay to have all that empty space in the wall? The thermal gap you called it?

@1845Barndo 4 ай бұрын

Thermal Bridging, yes, nothing wrong with that cavity.

@Zack-ei5kb 5 ай бұрын

I live in Longview, are the building permits very high for Gregg County and the other areas around it?

@Zack-ei5kb 5 ай бұрын

Also, do you have options for me to do custom floor plans?

@1845Barndo 5 ай бұрын

I wouldn’t say they are higher price wise but the process of obtaining is very very tedious in Longview

@nrolled2888 11 ай бұрын

Why not steel studs?

@johnmcinroe5893 Жыл бұрын

When your ceiling joists are 2ft centered like that Are you using 5/8 sheetrock

@meisdetermined Жыл бұрын

The 5/8 sheetrock helps the homeowner get lower insurance rate. I know that’s not what you asked but wanted to mention in case you were considering putting up that thickness.

@ryanbraggs8564 Жыл бұрын

Is this plan available for purchase?

@bcroft68bc 5 ай бұрын

This is like building a shop the building a stick built house on the inside of the shop. There’s no way that this could possibly be built cheaper than a stick built house.

@daktusdurggery5505 4 ай бұрын

My builder wants to use vynil insulation instead of spray foam

@1845Barndo 4 ай бұрын

Nothing wrong with vinyl, it just doesn't seal as well as foam without a lot of extra work. We use foam for its practicaly and application. We also use vinyl in some cases, but for heated and cooled areas we have found foam is better overall for our builds.