#Howto

No video

#Howto

Рет қаралды 1,337

Күн бұрын

How to setup and configure FrSky Tandem SR-18 for a MB-339 turbine jet. Follow me on this video as I walked you through the setup. Thanks for watching. #TDSR18
➤ For Reference to self check/setting up Stabilizing mode with full airplane (with similar receiver SR10+), please refer to this video: • #Howto #setup #Canards...
▼HELP SUPPORT MY CHANNEL▼
Subscribe ➤ www.youtube.co...
Buy Me a Coffee ► www.buymeacoff...

Пікірлер: 12

@carbidedge Ай бұрын

What a super video, good speed, easy to follow, well done, keep up the good work.

@8HrToGo Ай бұрын

Glad you enjoy it. Thanks for the kind comment. Happy 4th!

@juanmmondillo7347 2 ай бұрын

Thank you for the video, I will follow it step by step since I am very new to frsky but I am working to get things started with my radio and all frsky components. This video also helped me set up the multiprotocol so that I can use other receivers that are different brands. Fantastic information, thank you so much.

@8HrToGo 2 ай бұрын

You will like FrSky as many are transitioning to. Thank you for your kind comments.

@afterburnerrc6333 2 ай бұрын

Great video, FRSKY should pay you to make setup vids! I like how you went through the steps very quickly but made sure to emphasize information where needed. The stabilization mode can be tricky, is it better to check direction of flight surfaces first and invert where needed than run the self check or run the self check and then invert flight surfaces where needed? Also, I don't understand why FRSKY can't just do the calibration setup when the receiver is in the plane, like Spektrum, it just seems like a waste of time.

@8HrToGo 2 ай бұрын

Yeah I wish.. but I enjoyed doing these hobby videos to share with colleagues, friends and families, and for myself to go back to when forget things.. anything after that is bonus. For setting up stabilization mode.. please do the self check first along with verifying direction of flight surfaces as you move the receiver/plane to correct behavior to make sure gyro is working.. Then after that, get out of the script, and go back to the Outputs icon, and verify direction of flight surfaces normally. You can refer to the video (Howto setup Canards, Elevons plane with SR10+ FrSky #Stabilizer receiver) I attached in the description to see a similar setup on a full airplane with a similar FrSky SR10+ receiver (about at 7:00 minute mark). Thanks.

@Colt-4570 2 ай бұрын

Good video! It helps to have straight forward step by step visuals for things like this. I haven't done stabilized receivers yet, but your video makes it much less worrisome. Thanks!

@8HrToGo 2 ай бұрын

Thanks for watching. The FrSky receiver and stabilize feature are solid.

@kristanle 2 ай бұрын

You are very clear and helpful. 👍

@8HrToGo 2 ай бұрын

Awesome, thanks for tuning in.

@michaelpeck8677 2 ай бұрын

Not flying the TD yet but still helpful to watch. Your previous videos have helped me a lot. I do have one question. When I loaded the lua script for the SR10+ it created SRx Stable and SRx Calibration modules but did not create SRx Basic as shown in your video. Did something go wrong with the lua file load and, do I need SRx Basic? Keep up the great videos please.

@8HrToGo 2 ай бұрын

The SRx Basic is used with a RB Mixer, so you don't need it. But you should see it on your radio after u copied it over from PC. You can try to copy it again and see.