How to disassemble Huawei P8 Lite (2017), P9 Lite (2017), PRA-LA1, PRA-LX2, PRA-LX1, PRA-LX3.
Пікірлер: 28
@nathanwaller72425 жыл бұрын
Fantastic vid that not only shows a comprehensive guide but has party esq music feel to it also! Cheers
@AlexanderBestMobile4 жыл бұрын
have a fun party)
@dgouveia994 жыл бұрын
Thanks for sharing. Great to see.
@infidel20133 жыл бұрын
Спасибо. Единственное адекватное видео полной разработки.
@nicolasguillaume22643 жыл бұрын
Extremely useful Merciiiiiiiiiiiiii !!!!!!!!!!!!
@Ernest1335 жыл бұрын
Good job, thanks :)
@lahistoriade86323 жыл бұрын
Heyyy Alex your video was amazing...with Red Bull? Jajaja best regard from México
@user-sv1wd9ei2c9 ай бұрын
Where you buy the frame and display
@giuseppegiannotti41004 жыл бұрын
It’s a pain power flex cable teardown, I’m afraid I could damage it trying to put a cutter under it....you did so, did you?
@stuntwastaken10742 жыл бұрын
I don’t know that happened to my phone, but there where a lot of Tiny puncture holes
@jessmac23795 жыл бұрын
Thanks for replying. I followed your guide but now the WiFi signals are very low. Only captures good signal when I'm 1 meter away. Have you encountered similar to this?
@AlexanderBestMobile5 жыл бұрын
Are you connecting the Wi-Fi connector correctly? Did you damage him? they are very fragile
@jessmac23795 жыл бұрын
@@AlexanderBestMobile the UFL antenna cable is working good as I know how to test it using multitester. But the daughterboard UFL connector's ground and pin seem to be shorted. Can you test yours if it is shorted too?
@hassnainkhan77632 жыл бұрын
Mera pas mobile hai aap bana sakti ho
@hassnainkhan77632 жыл бұрын
Mera mobile ka screen dameg ho gya aap kuch kar saktai hu
@BmxAddict084 жыл бұрын
mine its not turning on....
@victorsantos23544 жыл бұрын
what did you use the heated bed for?
@AlexanderBestMobile4 жыл бұрын
I use it to soften the glue under the battery and under the flex cable
@victorsantos23544 жыл бұрын
@@AlexanderBestMobile how much time and how many degrees u have it on the bed for. - im gonna use an ansai 918B heat bed - im still learning the process . thx m8
@infidel20133 жыл бұрын
Добрый день, спасибо ещё раз за видео, все сделал как надо. Всё включается. Один момент - батарея не хочет заряжаться. 0 процентов и все, телефон выключается. Правда батарея лежала год без заряда. Не подскажите где копать?
@AlexanderBestMobile3 жыл бұрын
Попробуйте ее «разогнать» тобеш зарядить принудительно. Либо жабкой либо ЛБП либо обычным зарядником на 5 в. Плюс к плюсу минус к минусу, так чтоб на ней было хотя б 3,4 В.
@infidel20133 жыл бұрын
@@AlexanderBestMobile а не, все пошло. Спасибо. Минут 20 подумала и начала заряжаться.
@Darknat763 жыл бұрын
Hello ! I have a problem, I followed the tutorial everything works .. however my power button is kept pressed, the phone turns off and on again. The power button is not repositioned like the volume button. Any idea?
@AlexanderBestMobile3 жыл бұрын
Hikinata hi, try to put something thin under the bolts, or do not tighten the bolts to the end
@Darknat763 жыл бұрын
@@AlexanderBestMobile i have nothing to tighten? The power button does not react like the volume, there is a little red thing behind the power button, and when it makes contact and pressure on the printed circuit it does not come back on it like the volume button.
@AlexanderBestMobile3 жыл бұрын
Hikinata try to disconnect the flex for buttons from mainboard and plug the charger. Will it only charge or cycle on/off.
@Darknat763 жыл бұрын
@@AlexanderBestMobile That's what I did .. but it's not cool ... I bought a screen with a frame thinking it would be easy .. but in the end ..