Huge 60'X72' pole bar concrete pour. Was going soooo good and then?

No video

Huge 60'X72' pole bar concrete pour. Was going soooo good and then?

Рет қаралды 46,523

2 жыл бұрын

Check out the crew I got together for this monster pole barn concrete floor pour. There are some real good tricks to show you on pouring concrete at a pitch in this video. Hope you enjoy this video and subscribe if you haven't already.

Пікірлер: 91

@deandupree6335 Жыл бұрын

Hey mate concretor from Australia get some plastic chairs my brother. no more wire pulling ahaha. Great work guys you guys the best

@bondobuilt386 Жыл бұрын

Thanks Dean. When we chair it up the guys trip on it and bust there butts. LOL

@amunderdog 2 жыл бұрын

That was a large deal, Really worked the crew there.

@bondobuilt386 2 жыл бұрын

thanks

@SeanPalmer62 2 жыл бұрын

Wow that was a big job, very well done👍

@royordway9157 2 жыл бұрын

Great job as always Ron. It is interesting to see floor drains in a garage/shop for I assume trucks. Here in my area, Southern Maine, you can't do that unless you have an elaborate sewer system that is designed to separate the oil from the water but, you can sweep it out the door, go figure. I was taught to keep the reinforcing mesh or rebar in the bottom 1/3 of the slab or pier if only one layer was called for. These were jobs that may or may not have had an engineer's stamp on the plans. I started in construction in 1975 and learned from guys who were pouring concrete in the 50's. I know that now in residential garages and some light commercial slab applications, a lot of concrete guys use fiber in the conc and no wire or rebar. If the sub=grade is prepared right, nothing is going to settle anyway so when the concrete cracks, it ain't going anywhere.

@bondobuilt386 2 жыл бұрын

I agree the sub grade is the most important part of a slab. We use wire and fiber and always pull it up. I still catch he'll for the wire every video. I also agree it should be near the bottom 1/3 rd of the slab. That sucks you can't put a drain in a garage.

@Woodman_Custom_Sawing 2 жыл бұрын

When can I get a "HERE COMES THE MUD" Bondo Built tee shirt?

@tomvermeulen1082 2 жыл бұрын

I've been asking that question too. Seems he's a busy man. If he chose to use merch by Amazon I could even create the file.

@Woodman_Custom_Sawing 2 жыл бұрын

@@tomvermeulen1082 I'll encourage him to consider. He's a good friend of mine. We're due to have a beer together.

@Woodman_Custom_Sawing 2 жыл бұрын

@@tomvermeulen1082 I got my shirt! I told him he needs to do a live video and a social hour, maybe give a few away or sell some. 😁

@tomvermeulen1082 2 жыл бұрын

@@Woodman_Custom_Sawing I'd buy one! Hope it has the bud light/Pepsi in a koozie! The Koozie could have the "here comes the mud" on it. Let's do this!

@elvinsantiagomolina8881 2 жыл бұрын

Hola y saludos desde Puerto Rico, exelente trabajo

@taylorteresi5476 2 жыл бұрын

Work that in good that added exatrs at the end to make the lip . came out GREATTT

@bondobuilt386 2 жыл бұрын

thanks

@isaacjordan6052 2 жыл бұрын

Wish I could post a video here. My 2 year old got out of bed and came an watched this video with me an kept saying “here comes the mud” he wasn’t even downstairs for that part he just knows your voice 🤣

@bondobuilt386 2 жыл бұрын

That makes me smile for sure. I am glad you guys are enjoying the videos 👍🙂

@iowamatt2519 2 жыл бұрын

Nice job! Should turn those drains so the saw cuts line up

@bondobuilt386 2 жыл бұрын

Ya I wish he did that I didn't prep it.

@mauricekeithjohnson2598 2 жыл бұрын

At what area of pour, or type of mix, would you set the wire up on chairs for max strength ? Great job Material cost per yard ?

@ShredPile 2 жыл бұрын

Concrete cracks where it stretches so on a floor that is the bottom of the slab. The top is in compression and the bottom is in tension so the wire at the bottom keeps it from stretching more. It only takes a little bit of effort to tug it up into place where it will stay because it never goes all the way back down when you walk over it again. If you want to chair it up or put it on dobies then 1" dobies will put it in the lowest third of the slab.

@roryhamlet1886 2 жыл бұрын

Here comes the muuuuuud!!!!!

@GlenS123 2 жыл бұрын

Nice job on behalf of you and the crew! Can't believe the owner didn't put in PEX!! 😩 Don't even have to hook it up...

@bondobuilt386 2 жыл бұрын

Ya he didn't want it. made placing it easier. LOL

@frankbrockhoft3923 2 жыл бұрын

Now make sure that you do your saw cuts 25% of the depth of a concrete to make sure the relief cut cracks there I go 30% just to make sure I'm a professional concrete cutter for concrete coring company.

@joshuaweiler4566 2 жыл бұрын

Good content bro

@bondobuilt386 2 жыл бұрын

Thanks bud.

@mehmet284 2 жыл бұрын

great job as always

@pkope6849 2 жыл бұрын

Awesome Job Men !!!

@HendersonConcrete Жыл бұрын

Floor looks good, but why do you only cut an 1" deep? Floors are supposed to be cut 25% of thickness (unless you are cutting with a soff-cut the day of pour. You guys waited two days?

@MrSprintcat 2 жыл бұрын

Hard working Boyz.

@concreter6832 2 жыл бұрын

Why didn’t u put sawcuts of drain corners ,I thought it would crack off them ,nice finish.

@bondobuilt386 2 жыл бұрын

I did not put the drains in. They could have been turned and that would line cuts up.

@davidpatrick3533 2 жыл бұрын

We poured 55 yards of a barn floor just like this 10 days ago on a 40 degree day. Got the 4000 psi concrete from Vitale Robinson with 2% calcium (no steel in our floor), got it all down by 1030am, and by 330pm when we were power troweling it, noticed spider cracks everywhere. Have you ever seen that? What would you think caused that?

@bondobuilt386 2 жыл бұрын

I would say the surface was drying too fast. I have seen those micro cracks in stamped concrete before. Never in a power troweled floor. I would be calling Vitalle in case you have a problem down the road.

@jerry4012 2 жыл бұрын

100% it was the surface drying too quickly. Fiber mesh solves that issue, throw a pound or so per yard in the mix.

@bondobuilt386 2 жыл бұрын

@@jerry4012 yup 👍

@markhowes126 2 жыл бұрын

No vapor barrier on floor?

@bondobuilt386 2 жыл бұрын

I was just hired to pour it.

@CarrotDugTooDeep Жыл бұрын

@@bondobuilt386 Great job on the concrete! Wow, they (home owners) spent all that money on spray foam insulation and did nothing to stop moisture from coming up through the concrete. A plastic vapor barrier would have been cheap insurance to guard against moisture. They certainly spent a ton of money on this project, so I don't think a few hundred more for some plastic would have been a bank buster. SMH

@bondobuilt386 Жыл бұрын

@@CarrotDugTooDeep I have to agree.

@edstevens9357 2 жыл бұрын

That building is in the wrong place. It should be in my backyard. Nice job as always

@bondobuilt386 2 жыл бұрын

ya I wish I had it too Ed. lol

@2mnxffrddfghjbbvcdfh6644bcddcv 2 жыл бұрын

Looks good

@tommyfrancis7174 2 жыл бұрын

Sofcut day of!

@bondobuilt386 2 жыл бұрын

they wanted to seal it first.

@michaelbishop242 11 ай бұрын

rebar works the best laying on the bottom....

@stevehamman4465 2 жыл бұрын

Why bull float after power screed?

@boing615 2 жыл бұрын

do you have to fit expansion gaskets into the joints where you cut the floor?

@bondobuilt386 2 жыл бұрын

No you do not

@steveneddy9492 2 жыл бұрын

Think you bull float to Early ?

@concreter6832 2 жыл бұрын

1900 mesh on ground ,mesh should be 40 mm from top of concrete aprox.

@bondobuilt386 2 жыл бұрын

We pulled the mesh up with the hooks. I did that.

@concreter6832 2 жыл бұрын

@@bondobuilt386 do any of the jobs U do get pre pour inspection by a engineer?

@bondobuilt386 2 жыл бұрын

@@concreter6832 mostly the building inspector has to see it before we pour.

@jimanderson4495 2 жыл бұрын

With those foam insulation in the walls, I think they have pexed the floor. Thanks Ronny.

@bondobuilt386 2 жыл бұрын

He is using over head heaters uncle Jim

@concreter6832 2 жыл бұрын

What do u guys have against chairs under mesh? Instead of trying to keep mesh up , Why not pop a chair under steel ,then u know it is sitting at correct height and definitely of the ground.good job .

@bondobuilt386 2 жыл бұрын

How would we drive the trucks over the chairs without crushing it with the trucks. Also it is dangerous tripping hazard.

@concreter6832 2 жыл бұрын

@@bondobuilt386 I meant U chair up as the truck is unloading ,instead of using a hook U place chairs under mesh as U are uploading ,I know U can't drive over the chairs ,I have been laying concrete over 30 years,I thought U would of seen chairing while discharging the load ,hooks are not used in Australia as mesh isn't lifted high enough as we want reo sitting higher than half way ,it would not pass by engineer if not on chairs, everything here has to be passed by engineer before pour ,bit different in different countries.

@mauricekeithjohnson2598 2 жыл бұрын

@@concreter6832 Same here for chairs in the top Hemisphere, BERMUDA 32N64W Need the PITA Bldg Insp. signature before you pour. But nice job anyway.

@FredD63 2 жыл бұрын

Looks good … reminds me of when my business buildings were poured this pour is close to the size of my wood shop building …. 👊🏼👊🏼🪚🔨✌🏼🇺🇸🇺🇸

@kllisk 2 жыл бұрын

What! No vapor barrier?

@bondobuilt386 2 жыл бұрын

The homeowner did not want it.

@lachlanitis2311 2 жыл бұрын

No plastic underlay?

@bondobuilt386 2 жыл бұрын

No the customer prepared it and did not want it.

@lachlanitis2311 2 жыл бұрын

@@bondobuilt386 welp hope they don't build in an office and put floor coverings down.

@user-tm8ih5gg9i 2 жыл бұрын

тяжёлая работа..!

@MikeHoffey 2 жыл бұрын

Question. Do you cut it later in to sections to allow the cement to expand - expansion joints? - to avoid cracking in the future?

@bondobuilt386 2 жыл бұрын

We did cut it its at the end of the video.

@MikeHoffey 2 жыл бұрын

Thank you. I see that now. Do you put any type of material in the cuts?

@bondobuilt386 2 жыл бұрын

@@MikeHoffey you can caulk them but it is not necessary.

@charlesviner1565 2 жыл бұрын

👍HERE COMES THE MUD 👍👍👍👍

@bondobuilt386 2 жыл бұрын

😀 yup

@morrisnorwood3251 2 жыл бұрын

Any wire reinforcement not at least half way into the concrete is useless. Not a single chair in the pour. Professionals "place" concrete!

@bondobuilt386 2 жыл бұрын

you should make a video to show how you do it.

@joshuaweiler4566 2 жыл бұрын

@@bondobuilt386 Nice comment, I don't get this guys that are so particular about the wire mesh. I don't care if you jump up and done the mesh once you pull it up it's not going back down!

@bondobuilt386 2 жыл бұрын

@@joshuaweiler4566 exactly bud. These wire mesh police Kill me. Lmao 🤣

@cygnus1965 2 жыл бұрын

Bullshit! Where I’m from we pour.

@cygnus1965 2 жыл бұрын

Fiber is the only way. That wire mesh is only to make it a pain in the ass when it’s time to tear It out. I have torn out driveways where the mesh was right in the middle on chairs and the slab was cracked and separating like crazy. Just a pain to have to have a cut off wheel grinder and a set of bolt cutters at the ready the whole tear out.

@philipdamask2279 2 жыл бұрын

Riduculous waste of reinforcing wire mesh but fiber mesh should help.

@bondobuilt386 2 жыл бұрын

That mesh was all pulled up into slab by me.

@timtarran8124 Жыл бұрын

@@bondobuilt386 still having trouble with the wire mesh police 😂 still not every day you get to play in the mud with hoes😉 all the best from the UK bud