How To Rebuild Mazda Miata Shifter ~ Loose, Worn, Sloppy Shifting

Рет қаралды 71,263

4 жыл бұрын

Learn how to rebuild Miata MX-5 shifter. Worn manual transmission shifter is a common NA and NB Miata issue. Rebuilding the Miata shifter is great way to fix a sloppy or loose shifter. In addition to fixing the manual transmission shifter, learn how to fix a leaking turret, install new shifter boots, and fix a small transmission leak. You can also follow this guide to install a short shifter on a Miata. #humblemechanic #miata
Shifter Repair Kit ~ bit.ly/2GW7nVe
WD-40 EZ-reach ~ amzn.to/2UkMjQ6
WD-40 Degreaser 1 Gal ~ amzn.to/2twkQQl
WD-40 Degreaser Spray ~ amzn.to/36VEfb6
WD-40 Grease ~ amzn.to/2RYyWDr
~~~~ Support the Show ~~~~
Become A CrewMember ~ goo.gl/D7eROI
Patreon ~ www.patreon.com/user?u=4243029
Shop Amazon ~ amzn.to/2FQErAm
Audio ONLY Podcasts ~ goo.gl/5XcZxB
~~~~ Recommended Tools ~~~~
Impact driver ~ amzn.to/2HsxS2H
Small Impact driver ~ amzn.to/2DZdsMN
Electric ratchet ~ amzn.to/2FydxMS
Magnetic tray ~ amzn.to/2FEpQ6g
GrypMat ~ bit.ly/2L0a8XM (Use code HUMBLE20 to save 20%)
Basic hand tools ~ amzn.to/2GnjF7K
Box wrench set ~ amzn.to/2FzoJch
ScrewDriver set ~ amzn.to/2FEjcgd
Shop towels ~ amzn.to/2FC7UgM
Allen Sockets ~ amzn.to/2GlcnAz
Torx Sockets ~ amzn.to/2pL0SfL
~~~~ Playlists ~~~~
Humble Mechanic Podcasts ~ • The Humble Mechanic Po...
Project White Wookie ~ • MK3 VR6 GTI Project Car
Failed VW parts videos ~ • How VW Parts Fail
Tool and Product Reviews ~ • Tool and Product Reviews
How To videos ~ • How To Fix Your Car
MK1 VR6 Swap Videos ~ • VR6 Engine Swap MK1 Ca...
~~~~ Be sure to follow me at ~~~~
humblemechanic.com
INSTAGRAM ~ / humblemechanic
FACEBOOK ~ / humblemechanic
TWITTER ~ / humblemechanic
Amazon Store ~ www.amazon.com/shop/humblemec...
Disclimer:
The content of this video is available for informational and educational purposes only. It is not intended to be a substitute for the professional advice of a mechanic who has personally inspected your vehicle, nor does it create a relationship of any kind between the Humble Mechanic and you. Every situation may be different, and the Humble Mechanic does not make any warranties, whether express or implied, as to the accuracy, fitness, or applicability of the information or automotive parts portrayed in this video to any project and makes no guarantee of results. The Humble Mechanic and any sponsors of this video will not be liable for any damages related to personal injury, property damage or loss of any kind that may result from the use or reliance on this video and/or any automotive parts represented in this video. You are using the information and automotive parts portrayed in this video solely at your own risk.

Пікірлер: 201

@blockbertus 4 жыл бұрын

My takeaway from this is: - Ripped rubber is bad - Running dry is bad - Polish the rod - Always use lube - Slide the rubber carefully over the rod - Snap the rod into the hole - Rubber is for protection

@HumbleMechanic 4 жыл бұрын

100% this. And be sure to always get permission

@jeffr0 4 жыл бұрын

All words to live by

@lostathenian1836 4 жыл бұрын

🤔

@lipvandip6480 Жыл бұрын

Also boots aren't gaskets

@mania002 4 жыл бұрын

The most important step is getting permission from the wife to use anything from the kitchen. Great vid. Charles.

@stephanegenest6793 12 күн бұрын

After she see the video She said keep it .

@MotivxTools 4 жыл бұрын

"A 10mm socket... if you can find it..."

@HumbleMechanic 4 жыл бұрын

Never to be found again

@SeanBZA 4 жыл бұрын

@@HumbleMechanic I found it, and another one, plus 2 10mm spanners. Now, to find that 13mm spanner, I know I had at least 5 of the darn things, but all I can find are 12mm sockets, and only some bolts fit.

@king49334 4 жыл бұрын

You found it after bought new one.

@luisg1653 4 жыл бұрын

That hits home

@Patrick94GSR 4 жыл бұрын

Not sure why people say they can’t find their 10mm socket. I have the same ones I’ve had for 20+ years. Don’t recall losing any sockets actually.

@razvanalx8093 4 жыл бұрын

i don't have a miata, i'am 15 years old but i'm still watching because maybe i will own one

@HumbleMechanic 4 жыл бұрын

LEARN ON My friend!

@razvanalx8093 4 жыл бұрын

@@HumbleMechanic always :)

@ardonjr 4 жыл бұрын

I'm 33... bit same thoughts here. One day I might own one..

@king49334 4 жыл бұрын

Old miata is cheap.

@FDB77 4 жыл бұрын

Push on! I'm 16 and I just got my own Miata a few weeks ago. Save up and convince the parents lol. Good luck!

@Flatbasset 3 ай бұрын

I just bought my son a Eunos Roadster (RHD JDM version of an NA Miata). He cant afford a mechanic and we're fixing all the quirks ourselves so content like this is invaluable to us!

@naterinehart2142 10 ай бұрын

After watching a bunch of different videos on this I’m so glad I found this one. Fantastic advice, straightforward explanations, and good lighting throughout. Love the content!! Thank you sir.

@HumbleMechanic 4 жыл бұрын

I am not sure I mentioned it, but the oil residue is from the rubber boot being split and sloshing fluid out. I could have probably not resealed that housing. If those boots are split you can get a leak like this.

@becoming.andreia Жыл бұрын

Why oh why couldn't I find this video yesterday. Managed to install a short shifter somehow, a 1h job that took me 4h and 4 different youtube videos, none of which ever got into the exact minute detail of instalation like you did. Subscribed for next time! 🎉

@justinsingh4138 4 жыл бұрын

Excited that you got an NB Miata! Can't wait to see what mods you go with.

@mh-ic6zj 4 жыл бұрын

that was a smooth video cut from exposed-pins to towel covering it. great tutorial, exactly what I need for my miata

@LFSPharaoh Жыл бұрын

I'm like 90-95% done, takin my sweet ass time. Just wanted to say thanks for the very thorough and also concise video. After a quick scan, I only referenced back to your video whenever I needed another refresh. Noticed a few other videos skipped important steps/details that I would've overlooked/forgot about, due to lack of experience. This video made this job very easy for me (and possible haha).

@dad_rod1943 10 ай бұрын

Who would’ve thought that after selling my GTI and buying an nb Miata I would find myself right back on a HumbleMechanic video. Quality (and much appreciated) as always Charles, now please bring back Cars With Cocktails!

@HumbleMechanic 10 ай бұрын

HAHA HELL YES!

@thomaspeterson8659 4 жыл бұрын

Another very comprehensive how to video ! Anyone with minimal mechanical skills could do that job by watching it.👍👍

@HumbleMechanic 4 жыл бұрын

thank you!

@jamesk3565 4 жыл бұрын

I noticed you forgot to mention the toothbrush you used for cleaning. DO NOT USE YOUR OWN TOOTHBRUSH!!!!!!! The wife's toothbrush is completely fine to use.😂😂😂😂😂

@HumbleMechanic 4 жыл бұрын

DAMN! I did. I also used my wife's brush so I wasn't worried. HAHA

@YuStudios 4 жыл бұрын

Currently have been watching your videos and doing work on my mk6 GTI! Just bought an NB2 miata earlier this month and I can't believe my favourite VW mechanic got one too! Can't wait to see what you do to it :)

@HumbleMechanic 4 жыл бұрын

Awesome

@lobosnumberfive2210 9 ай бұрын

Great video! One thing to add is that on 2001+ NBs there is an extra screw under the power window assembly. There are tabs on the front and back of the assembly so you need a credit card or something to pry it out gently. Then you can take that screw out and the console will come loose. Otherwise spot on!

@pammuirheid838 2 жыл бұрын

Thanks for a great video! Like the clip at which you talk….quick but clear.

@moisesjpagan 4 жыл бұрын

I get a miata and this comes up on my feed! Thanks humble mechanic 👍

@HumbleMechanic 4 жыл бұрын

Sweet!!!

@vfhondas 3 жыл бұрын

Great job Charles ! Looking to do mine soon. On a side note just turned in my 16 GLI (end of lease) Man I miss that car!

@HumbleMechanic 3 жыл бұрын

That’s a great year for the GLI

@Douwantapotato 3 жыл бұрын

what a great informational video! THANK YOU

@kalebworth8347 3 жыл бұрын

Most quality video on rebuilding the shifter thanks g.

@kalebworth8347 3 жыл бұрын

Holy shit just took mine apart and I have a completely different turret

@jeffw2218 4 жыл бұрын

I am glad you asked permission this time. 😀 That Pyrex measuring cup is still missing from the kitchen I'm guessing!

@HumbleMechanic 4 жыл бұрын

Hahaha I think momma is cool with it. Gives her a reason to buy another one

@hectorsmith921 9 ай бұрын

Thanks good video good explained information n understandable .thank you

@gaborherman1481 4 жыл бұрын

Great job Charles! Just don't give up on VWs, please.

@HumbleMechanic 4 жыл бұрын

Never!!!! Maybe one day the worlds will come together

@brandandahl5460 4 жыл бұрын

I'm a little late to your channel, sorry . I just bought a 2018 R and will be closely following your build for sure! Just curious if your\'re swapping a SC VR6 into the Miata? I feel like you might be the first to do that

@brihal6498 4 жыл бұрын

Sweet Vid! Now I know how to spend the weekend! Love these Miata vids. Glad u made in back from Finland 🇫🇮. This wouldnt help the problem of getting into 1st gear would it. Seems like ours is fickle if the car is going more than 5mph.

@HumbleMechanic 4 жыл бұрын

Possible. If that cup breaks it can be tricky

@brihal6498 4 жыл бұрын

Might as well try! Ur the best Charles. Keep up the great work! I tell everyone about ur channel 👍

@imwmanish 4 жыл бұрын

Thank you sir iam waiting your video Nice 👌 video 👍

@behindthen0thing525 3 жыл бұрын

Great video. Thanks man

@therealderjett 4 жыл бұрын

All 10 mm sockets should be painted a bright color. The last time I moved I found 4 in my garage along with random missing torque wrench that was likely dropped behind the bench. The many Sunday night repairs to get the car on the road Monday for work.

@papajohnscookie 4 жыл бұрын

the brass bushing is a great mod to do to

@DirtDude117 4 жыл бұрын

If you put a clear hose on the end of a baster then you can do this stupid easy. Also getting a scuff bad from the kitchen and some vinegar really cleans these up quick and easy.

@SalemAbuOmar 4 жыл бұрын

for vw hot change the reverse lock to the newer desight like in t5 pull up

@pete5534 Жыл бұрын

Thank you!

@osalcedoucmsae 4 жыл бұрын

@HumbleMechanic I test drove a 2001 Miata with a 6 speed and while driving, the shifter was able to move almost freely like it was in neutral. Is that bad bad or can doing the steps here fix it? I want to buy the car but this is one of the things I’m concerned about. Thanks!

@TopiasSalakka 4 жыл бұрын

Is the process similar for a front wheel drive car? I have a 1998 Mazda Lantis with a pretty sloppy shifter.

@martinpantak4765 3 жыл бұрын

top video ! thank you !

@brianreese9318 4 жыл бұрын

Good information

@kelvinfewings3631 2 жыл бұрын

is there a reason to remoove the pin at 12:08 whilst the turret is in the car? seems like it would be easier to replace the seat whilst this bit is out of the vehicle.

@mainoffender1 4 жыл бұрын

Is the shifter the same for the NB 5-speed and 1999-2000 the same? If not, will it fit and work?

@agenericaccount3935 4 жыл бұрын

When I did mine, I just took an old beach towel and cut a hole in the middle, draping the rest over the interior carpet. Like an operation.

@HumbleMechanic 4 жыл бұрын

HAHA I like that!

@agenericaccount3935 4 жыл бұрын

@@HumbleMechanic Kept the carpet super clean. Twenty year old stank gear oil never scrubs out.

@tudor3874 9 ай бұрын

What type of grease can be used for the shifter? Does copper grease work?

@nathanwinterroth2751 4 жыл бұрын

I remember when you did the shifter bushings on the R32 (fantastic video btw), just out of curiosity, how much more difficult would it be to do a shifter bushing kit for a 20th anniversary Mk4 gli? Anything to watch out for specifically before diving in?

@HumbleMechanic 4 жыл бұрын

It should be exactly the same as the R32. So only 400x harder than this car. Hahahahahha

@nathanwinterroth2751 4 жыл бұрын

@@HumbleMechanic LMAO 😂

@edgarcastaneda9086 4 жыл бұрын

great video Charles By the way do you know the part number or something related to do this job on an B5 Audi A4 my shift knob feels a bit loose and i want to refresh it. Thanks

@SeanBZA 4 жыл бұрын

There is a whole kit of the plastic parts for this, either aftermarket or from VW spares. Mostly easy to install, though you will benefit from a lot of rubber grease to help with the places where they go into the housings and where all the sliding parts go. My VW was sloppy, and the one plastic bush for the ball was out of stock, so replaced the rest, and then simply used a lot of cable ties and rubber grease to make the fit better.

@themechanic6117 4 жыл бұрын

Nice video👍

@1147cc 3 жыл бұрын

Cant wait to see him replace the transmission mount

@HumbleMechanic 3 жыл бұрын

Hahah yeah mine is a Bluetooth mount.

@stoneluger398 Жыл бұрын

Hello! Thanks for the informative video. I have a question I haven't seen asked here. I see you've a roll bar and some sort of speaker box in your miata. Do you know the make/ model of those parts? I'm trying to find which are compatible. Thanks!

@HumbleMechanic Жыл бұрын

I think the PO made it.

@JohnMaffa 4 жыл бұрын

Great Job as always. Question, what do you do with the dirty WD40 Cleaner degreaser? Does it have to be disposed of properly?

@HumbleMechanic 4 жыл бұрын

Well what I did was leave it on the floor, kick it over, spill it, then use an oil absorbent towel to clean it.

@JohnMaffa 4 жыл бұрын

@@HumbleMechanic It's nice to see that superstars like you make some of those same mistakes that I make. I hope you didn't break the Correlle ware : )

@loganarzuaga8316 2 жыл бұрын

16:28 the miata does not have transmission mounts the transmission is held in by the engine and the power plant frame attaching it to the differential

@xninpo 3 жыл бұрын

The Best.

@sorasoki 6 ай бұрын

thx mate!!

@dha588 9 ай бұрын

Are you using Lucas Red N Tacky grease?

@williamreadon9052 4 жыл бұрын

same design as early jeep manual trans, that damn bushing always was sloppy

@jhuntosgarage 4 жыл бұрын

Even with the plethora of lights, it seems like the lighting is off. Oh wait, screen brightness! Perfect! Any need for antiseize on the bolts in the trans housing?

@HumbleMechanic 4 жыл бұрын

I didn't use any. But I rarely use any.

@Patrick94GSR 4 жыл бұрын

No need, it’s all aluminum.

@CommentingTheTruth Ай бұрын

I didn't notice the orientation of the shifter. It went in both ways. My shift knob is 180 degrees out. I fixed the shifter knob lock screw and all is fine. I don't know that it really matters. Shifts the same as before.

@jasonbrown1237 4 жыл бұрын

I’m going to HR in the morning lol, you said to lube your shaft to slide the rubber over it

@HumbleMechanic 4 жыл бұрын

😂😂😂🤪

@jeffruebens8355 4 жыл бұрын

I would add a lot of Fluid Film spray on both sides of the rubber parts, so they do not crack from age as quickly. It is made from lanolin from sheepskin. Not for door gaskets- use silicone spray or Mothers VLR spray instead.

@HumbleMechanic 4 жыл бұрын

Dang what’s the rubber made of. Lol probably a solid idea

@jeffruebens8355 4 жыл бұрын

@@HumbleMechanic most rubber now is not the sap from a rubber tree like the old days- it is made from fossil oil and chemicals. I use Mothers VLR spray for interiors- made for vinyl, leather and rubber. Fluid Film spray is good for most rubber, leather and motorcycle chains- it does have a slight bad smell. The Mothers VLR spray smells good. I use Turtle Wax Trim Restorer for hard unpainted plastic inside and out. The Fluid Film spray might damage door gaskets. I prefer the Mothers VLR spray instead of silicone spray because it smells better, but the silicone spray works better for side window channels. Silicone spray will ruin oxygen sensors.

@BigRobChicagoPL 4 жыл бұрын

I was driving around a Toyota Echo with a shifter so messed up it essentially would kind of flop around as you drove, and the gear pattern was more your imagination then actual pattern. Put it in 1st? Think I'll just slide into the neutral position but just enough to still be 1st.

@HumbleMechanic 4 жыл бұрын

That is so tough to drive with. LOL

@sweeetlow 10 ай бұрын

what gearbox fluid is that?

@Rangatron01 4 ай бұрын

I cannot stress enough how tough those pins are to smack out, like I had a pretty heavy hammer and smashing a punch into it on the floor making dents in the concrete floor tough (exaggerated). Anyone doing this make sure you got tools that can really smack on those pins.

@Mrizing 4 жыл бұрын

Love the channel been a big fan since the early days keep up the great work! I had a quick question I know this is off topic but I need help, if anyone here or you can point me in the right direction it would help me a lot. Heres whats going on, I have a 1991 jeep cherokee 4.0. 217,000 k miles on it, it was burning oil so I had no choice but open it up and see what is going inside. Took off the head saw bad burnt values so I started with the head took them all out cleanded them up and did value job with compound and that rubber tool to re seat them everything looked perfect after that seat was perfect also value steams where changed few months before this so they looked OK. After the head I saw the block walls where smooth with no cross patterns left, so I took all the pistons out rings where not stuck or brunt they moved freely, next I re hoaned the walls to make the crisscross pattern I removed all the rings and cleaned all pistons up everything was super clean and rings where moving like they where new I also replaced the piston bearings cause they showed sign of wear. Before I put everything back I did a simple test put one piston in and poured oil on top of it to see if oil would drop through the rings left it for 2 days no oil went through I did the same test before I did the hoan and clean up of piston rings and oil fell through within hours. So I thought this was a good sign. after hoaning and ring clean up I believed rings where tight and no blow by was going to happen. Then I put everything back in. the car stared perfect and I thought everything was great then I did compression test each read same reading 125.125.125.125.124 126. So I drove it about 100 miles and oil was below safe line, OKi though maybe the rings need time to set in new block walls but no 1000 miles later I'm burning even more oil then before almost a whole quart every 70 miles that's really really bad. My mistake I feel is because I didn't replace the piston rings ? But they looked totally fine and where moving with ease. Please what do you think I did wrong here? I don't want to give up on this jeep but this is crzy how much oil it's going through I'm willing to take it apart again trying to fix it, currently it has good power no blue smoke but the oil I just disappearing. Sorry this is so long but I'm so lost and any help would be greatly appreciated.

@HumbleMechanic 4 жыл бұрын

Could be piston rings. Is the oil burning? Meaning smoke from the exhaust?

@Mrizing 4 жыл бұрын

@@HumbleMechanic no it's white smoke not blue

@Mrizing 4 жыл бұрын

@@HumbleMechanic So my My compression on all 6 cylinders is between 125 and 126. Is that super low? Or just low? What if I went and bought sleeves the for block, would I have to to get all new pistons? Definitely new pistons rings

@lukerinderknecht2982 3 жыл бұрын

@@Mrizing you ever get it figured out?

@Mrizing 3 жыл бұрын

@@lukerinderknecht2982 hey thanks for asking no I haven't been able to get my oil so stop it from burning. I need to get off the net but I will write tomorrow s And as best as I can what I did do the jeep engine. Thanks I hope u help me.

@onizuka186 Жыл бұрын

Is the NA and NB the same shifter?

@candycornpeeps 3 жыл бұрын

Hey @humble mechanic, I redid the shifter in my 99 transmission I'm wondering do you feel the shifter when pulled to the left to go into first and second moves less than when you go to the right for 5th? This car is new to me so not sure if this is normal if I got bad transmission or maybe did something wrong on the install.

@HumbleMechanic 3 жыл бұрын

Felt great after. Did you replace that little cup at the bottom?I guess make sure nothing is binding.

@candycornpeeps 3 жыл бұрын

@@HumbleMechanic sure did with a brass one as well. The movement is fine mostly concerned about the left to right difference. To the left it's a short move and to the right it's a longer move is yours the same way?

@miketeeveedub5779 4 жыл бұрын

Wife: "Charles, where's my casserole dish, turkey baster, and measuring cup?" Charles: looks around sheepishly...runs for dear life! Now we know the truth about the garage door. The missus ran Charles through it!

@HumbleMechanic 4 жыл бұрын

Hahahaha it was a disaster

@robbykalany4730 4 жыл бұрын

Is bsh speed shop still in business?

@brittfuss1 4 жыл бұрын

HumbleMechanic, are you on Garage Amino? I installed the app on my iPad based on your recommendation in an earlier video of yours that I watched. I tried searching for you but came up empty. Thank you.

@HumbleMechanic 4 жыл бұрын

I was a few years ago. I haven't been on in forever.

@brittfuss1 4 жыл бұрын

HumbleMechanic, thank you for the response. I plan to delete my account and remove the apps from my iPad. As soon as it launched I knew I would not like it. It's just too busy for me and navigation is not intuitive. I have enjoyed watching your videos.

@brianreese9318 4 жыл бұрын

The simplistic way clean scrub rub redo clean grease reinstall with new clips seals woo

@Mrizing 4 жыл бұрын

@HumbleMechanic So my My compression on all 6 cylinders is between 125 and 126. Is that super low? Or just low? What should they be? What if I went and bought sleeves the for block, would I have to to get all new pistons? Definitely new pistons rings

@HumbleMechanic 4 жыл бұрын

That’s pretty low I think limit is 110. Before I did any mechanical repair I’d try some BG compression/Engine performance restore. If you got sleeves you’d need to have a machine shop do the work. I’d do more digging before I took the engine done

@Mrizing 4 жыл бұрын

@@HumbleMechanic so u think I should just get new pistons rings and make do a little more Hon? I reason I think that the rings where not bad was able to pour oil after the Hon and put old rings and pourd oil on top to to see if it would seep thour and it didn't for 4 days....... So that made me think piston rings where OK I guess not a good test?

@HumbleMechanic 4 жыл бұрын

Not yet. I’d do a leak down test and find where the low compression is coming from

@erikanovember9485 8 ай бұрын

Have you tried that wd degreaser in a sonic cleaner yet?

@HumbleMechanic 8 ай бұрын

No. Sadly my sonic cleaner died .

@erikanovember9485 8 ай бұрын

@HumbleMechanic harbor freight cheap and easy to replace when they break. Love mine. Ill have the to give the wd a run on some random stuff and let ya know

@antont8323 4 жыл бұрын

Is it the same transmission as 1992 Mazda B2200 5 speed manual

@HumbleMechanic 4 жыл бұрын

That I do not know for sure

@300DBenz 4 жыл бұрын

None of those screws are Phillips...they’re JIS cross-head screws. Using a Phillips will damage them. (I chewed up a LOT of screw heads before I learned that.) Late ‘80s Mazda B series trucks had the same nylon bushings in their stick shifts.

@nickpappas4133 4 жыл бұрын

Not many know about the JIS screws,getting harder to find proper screwdriver

@jeffruebens8355 4 жыл бұрын

@@nickpappas4133 for a Japanese motorcycle, use the tool kit screwdriver for the screws. Do not use the tool kit spark plug socket for the front axle bolt, because it will likely bend it for spark plug use. A lot of people replace the x or flathead screw heads with allen head screws.

@davisdecker1968 3 жыл бұрын

Would replacing it with a new shifter or short throw shifter fix this in the process?

@HumbleMechanic 3 жыл бұрын

Yep exactly the same.

@mickholgate3347 4 жыл бұрын

Where should the grounding electrode be clocked too?

@HumbleMechanic 4 жыл бұрын

If you’re going down that path, the majority seem to land on 180 out from intake valves/ injector. This is one of those things that the theory is sound, and there man be a SLIGHT benefit, but probably not worth the time or added cost. But I think the next cylinder head I have off I may do it just to do it

@mickholgate3347 4 жыл бұрын

@@HumbleMechanic thanks for your reply mate, greatly appreciated.

@ateamfan42 4 жыл бұрын

You can't improve the transmission wiggle with trans mounts, because there are no trans mounts. Miatas have two motor mounts and two differential mounts. The trans is solidly connected in between the two (with the PPF bridging the trans to the diff)

@HumbleMechanic 4 жыл бұрын

Got some freshy engine mounts ready to install

@knduong 4 жыл бұрын

"Sealant" is the word for this video :P

@HumbleMechanic 4 жыл бұрын

I thought it would be turret

@MindMasterJ 4 жыл бұрын

Surprised you didn't spring for using "Unicorn Tears" (Motorcraft XT-M5-QS), understandable though cause its so expensive. I'm probably going to use Redline MT-90 for mine when I do it soon.

@HumbleMechanic 4 жыл бұрын

Yeah I hear that’s the best of the best. Lol

@Patrick94GSR 4 жыл бұрын

I used Motorcraft fluid in my trans and Redline in the diff. RockAuto has the Motorcraft fluid for a decent price. Only 2 quarts needed.

@mychannel9160 4 жыл бұрын

Miaaaata!!! :-)))

@howardwhite9773 4 жыл бұрын

vroom-vroom noises from Bad Obsession Motorsports ;)

@HumbleMechanic 4 жыл бұрын

YASS!

@texasmagpie 3 жыл бұрын

"... a 10mm socket, if you can fin it". I just bought YET ANOTHER yesterday. It's right h... well damn.

@HumbleMechanic 3 жыл бұрын

Hahaha

@12wingwfetech 4 жыл бұрын

A little lubricant helps once and a while

@king49334 4 жыл бұрын

If any of the seat of bushing is worn it will pop out of gear.

@Pete.Ty1 4 жыл бұрын

👍

@tedbonbrake1967 4 жыл бұрын

A Phillips Head Screwdriver that actually fits the screw would be nice though...

@nickpappas4133 4 жыл бұрын

The design of a Japanese Phillips screw and North American is different.You need a Japanese screwdriver for a proper fit.Most motorcycle tech’s know this.A sae Phillips screwdriver will cam out on a tight screw.

@tedbonbrake1967 4 жыл бұрын

Interestingly enough I was in the motorcycle industry for 45 years as a tech, service manager, and finally a technical coordinator for Yamahas International. That’s probably why this stood out so much to me in the first place.

@nicknicu1787 4 жыл бұрын

It seems you’ve realized that lower bushing is metal from the factory and installing a plastic aftermarket one that comes in those kits is actually worse than the one it came with from the factory. So pulling that pin in the NB cars is unnecessary unless someone was harsh enough with the shifter to crack the metal bushing or the weavy washer. AFAIK,the NA cars had a plastic lower bushing and that’s why those kits come with it.

@HumbleMechanic 4 жыл бұрын

Interesting. I’m learning so much about these rascals. Like the weird rear calipers. Hahaha

@YZJB 4 жыл бұрын

HumbleMechanic what’s weird about the rear calipers?

@moniack 4 жыл бұрын

@@HumbleMechanic They are funny. Mine were completely rusted and I couldn't turn the screws to retract the piston. I got a used set from Roswell Wrecking that looked brand new with pads for $40!

@Patrick94GSR 4 жыл бұрын

No, that’s incorrect. The plastic bushing was OEM on all 90-05 Miatas. The bronze aftermarket bushing is a worthy upgrade when rebuilding the shifter.

@emmexfyv Ай бұрын

@@Patrick94GSR yes, true.....none were metal from the factory, and the plastic fall apart often with nothing remaining.....i just did my '02 5-spd yesterday and it was a sloppy floppy loose shifting mess - a couple tiny chunks of that white plastic bushing was all that remained down in there after 90k miles. The new brass (or bronze?) one makes for sweet snicky shifts.

@toddyrocks 3 жыл бұрын

a little trivia !! a chemist told me that WD40 is modified fish oil

@MagnetbergOfficial 4 жыл бұрын

Sadly my 1998 Golf Mk4 has the same issues

@HumbleMechanic 4 жыл бұрын

Luckily is a pretty easy fix

@MagnetbergOfficial 4 жыл бұрын

@@HumbleMechanic But i have not the Shifter with the PVC ball but with the kinematic.It's only adjustable with the 2 special tools VW 3422 and 3192/2 but I bought both last year and now I found the part numbers for the rolls and bushings.Fingers crossed that all this works. Thanks again for your great Video's.

@sethriggle1462 4 жыл бұрын

2 days Prior the humble mechanic searches on KZfaq “how to replace shifter on Miata”

@HumbleMechanic 4 жыл бұрын

Nah it was long before that

@sethriggle1462 4 жыл бұрын

HumbleMechanic lol

@sethriggle1462 4 жыл бұрын

Why didn’t you just install a short shifter anyway?

@HumbleMechanic 4 жыл бұрын

Because I want to be sure there is nothing else wrong in the transmission. I didn’t want to add a non-stock variable If something is wrong

@mellowness65 4 жыл бұрын

No transmission mounts on these, only engine and differential mounts, everything in between is metal

@HumbleMechanic 4 жыл бұрын

Ah good point. A strange truth I think. Ahah I have engine mounts ready to go.

@Patrick94GSR 4 жыл бұрын

HumbleMechanic that’s the power plant frame unique to Miatas. They use it to keep the engine trans and diff all rigidly mounted as one unit, then put the rubber mounts at the engine and diff only. No need for trans mounts or any rubber on the drive shaft. And I can attest that the Mazda competition rubber mounts make a huge difference if your old ones are torn like mine were.

@Tigerfire75 6 ай бұрын

That wasn't just sound deadening but also heat shielding.

@Patrick94GSR 4 жыл бұрын

Haha the infamous broken NB1 console lid plastic hinge. What a ridiculous piss poor design. Nice DIY repair from the previous owner with the brass hinges. I used a piano hinge to make a pretty nice replacement. Just need to paint it black.

@HumbleMechanic 4 жыл бұрын

Yeah their repair was pretty solid. Lol

@IncurZeAwperator 4 жыл бұрын

grease the ball

@braddowns17 4 жыл бұрын

Charles does the wife know you stole her casserole dish?

@HumbleMechanic 4 жыл бұрын

I asked first. Lol this time....

@braddowns17 4 жыл бұрын

@@HumbleMechanic lol always good to ask first

@sdtunstall 4 жыл бұрын

Did you get permission on the wife's toothbrush as well ? :)

@HumbleMechanic 4 жыл бұрын

Lol I actually did. But she hasn’t asked for it back yet

@moedalgarny 4 жыл бұрын

the piece need the grease..because the grease make the piece work nice in peace 😂🤨

@HumbleMechanic 4 жыл бұрын

TRUTH!

@nolahahnshouse3389 4 жыл бұрын

Dude please put a short shifter on it! I promise you it make a huge difference! God l miss my Monica!

@nolahahnshouse3389 4 жыл бұрын

Get a couple of rubber gaskets also! The wear out very easy.

@HumbleMechanic 4 жыл бұрын

I probably will. But I want to get a feel for it this way first

@Patrick94GSR 4 жыл бұрын

The only short shifter worth anything for a Miata is the Miata Roadster shifter which is about $350. It’s the only true short throw shifter that raises the ball and lengthens the lever arm below the ball. All other shifters on the market are just shortened height levers.