Awesome video! I like how you're watching the video from the same angle as if you are watching yourself work at the work bench. That's a fun way to do it.

Great video. I just had to hit the "Subscribe" button, as I learn a bit from your video and really liked your presentation. I will go through my 440 and PM it. I will have to see what other videos you have on your channel. Nice workbench! Thanks again.

Awesome video. I like your professionalism. Great work.

Great video, I like your efficiency, thanks for sharing 👍

I bought this exact same saw not knowing how to start one of these. The seller said it was a return no start, but he bench tested it brand new worked perfectly. I took a chance and bought it. I could not get this saw to start at all unless I held the throttle wide open and almost cutting my leg off a few times. My buddy was into the tree cutting service and had a large monster one of these and had the same issues. It would only start if you tacked it right out. I found out from a simple youtube video that you need to read directions and follow common sense when starting these. Press the primer 6 or 10 times, move the lever to choke to lock choke and high throttle, it should only take 2 pulls on a bad day to get it to bark off, then without touching the throttle at all, move the lever to the normal run position, pull it and let it rev out for about 5 seconds or so then she will be good to go. This year, it does none of that and only runs if I pour 2 cycle gas in the cylinder with a new plug, it still doesn't run at all leaving me to believe its a major carb issue. One of the reasons why i'm here so thank you for going over this saw with us. These are just light duty homeowner specials and no one wants to work on them, but this saw ran for 7 years straight every year until this past year when it didn't.

Yes awesome wins you were available here.

The airgun is genius, I was using a plastic brush to clean mine and it took hours.

Lol, the first day I bought my Husqvarna 435 I cut into some punky wood and the nose sprocket jammed up just like that. Took 2 minutes to figure it out and clear the sprocket. Absolutely no problems after that. Just new saw testing me out, lol.

People need to follow u

Keep slamming it down like that it will need alot more than a tune up 😂 great video

Working on autos you can never just go by the customers diagnosis. Gotta check for yourself. You can use their diagnosis as a jumping off point and I imagine it's the same with small engines. I got stupid and mounted a 14" OREGON Bar and Chain on my Ryobi 18V cordless 8" Pruning Chainsaw. Best thing I ever did. I'm not expecting to be felling 200 year old cedars with it, but it clears the trails of downed branches and trees perfectly. I can get better reach with the 14" bar and it cuts so much faster and cleaner than the 8" bar and chain that it comes with from the Ryobi factory. I pondered getting the Ryobi 40V 14" chainsaw but ultimately the excessive weight and size became an issue with that. It was a direct bolt in swap that took less than 15 minutes and came at a cost of $30 for the OREGON bar and chain.

có ốp lam bán không ạ

I have the Husquvarna 440 x torq. It has been gutless out of the box compared to all the Huskies I have had in the past, EXCEPT when it runs out of gas. The Last few seconds of gas the saw performs like a champ. Any thoughts or insites would be appreciated.

This is perfect. Thank you for making this. Question - do you recommend an aftermarket bar and chain, or is the Husqvarna bar and chain good enough. I use it like 1-3 times a year. I'm that customer.

Thanks for the videos sir. I was wondering, what type of grease are you using when you are applying grease to the needle bearings on the clutch of the chainsaws you are working on? I've been watching you use the squeeze tube grease, but haven't been able to catch what kind of grease it is. Thank you for your time.

Good tune up, but have to wonder if, the person who brings a perfectly good running saw in to free the bar sprocket is competent enough to be using the saw in the first place?

Do you have to be qualified for repairs service like this you offer? I've been fixing saws myself for years now and wondered if I should branch out and build a service shop.

Great video. What would you do for a husky 440 that runs 50% but not WOT? Thanks.

I have a one 4 yr old one, has bout maybe 9 hrs on it, e series, only likes to start when I hold gas trigger all the way?, is there a carb adjustment on these, new to this brand, usually run stihl’s

Why did you wait to start it before performing the tune up work?

Where do I find me a pressure gun like that

Hey umm I am working on my saw now it will start up then it will die and I can't restart it for a long time. I am looking at the gap and I am not sure how big or small it should be would you happened to know

It was already off,the kill switch wire

Lack of bar maintenance or just one of those things. What weight of grease. They make it harder on you sometimes.

My 440 won’t drink oil??

Not a fan of those tool-less chain adjusters.

👍⭐⭐⭐⭐⭐🫡🏆

This saw is junk

😎