HUXWRX Flow 762 Ti

HUXWRX Flow 762 Ti - Overview

Рет қаралды 19,525

Күн бұрын

FLOW THROUGH - NOW IN 7.62!
Huxwrx took everything loved about the Flow 556K, and made it a bit bigger. The Flow 762 Ti has the same zero-backpressure as its little brother but in a full Grade 5 titanium build. The reduction in backpressure will make sure your semiauto firearms in 5.56, 6.5, or 7.62 cycle naturally. This minimizes excess wear on components, reduces recoil, and provides better at-the-ear decibel reduction than the competition.
Even being all titanium and just 11.8 ounces, the Flow 762 Ti was able to easily survive 6 cycles of the SOCOM Reliability Stress Test. Strength, weight savings, and industry-leading backpressure reduction is achieved through 3D-printing. When compared to traditional baffle creation, 3D-printing allows for much more intricate designs and methods of suppression not possible before.
The Huxwrx Flow 762 Ti also utilizes the Torque Lock mounting technology, allowing the shooter to be confident the silencer will not loosen during adverse conditions or hard use.
FEATURES
Fully 3D printed
Built from 6AL 4V Titanium
Zero backpressure
Ultra-lightweight
Optimized for low-light conditions
Cerakote finish
WHAT'S INCLUDED
Instruction Booklet
Silencer
Sticker
Tool
COMPATIBLE ACCESSORIES
Torque Lock QD Flash Hider
Torque Lock QD Muzzle Brake

Пікірлер: 104

@gronthomson 3 ай бұрын

Just purchased a HUXWRX Flow 762 Ti in FDE from you, Capitol Armory. This is my second suppressor purchase from Capitol Armory. You're FANTASTIC! The wait from ATF is ON!

@travisolexa3074 11 ай бұрын

So finally we have a 30cal can that performs on par with a RC2 at muzzle with 5.56 measuring in at the same length, reduced weight, and flowthrough. THIS can is truly the White Whale 30cal the community has been chasing. Time to lose $1600.

@JNOSNOW 5 ай бұрын

I was wary of the $1600 but I waited just long enough and got one at $999. Hope you already have yours by now

@rodarnold6168 7 ай бұрын

Great video!!

@puddle_pirate95 8 ай бұрын

Hope to have one someday.

@jimc2993 8 ай бұрын

great product

@bobbyday8690 7 ай бұрын

Badass!

@MrOsoverde 3 ай бұрын

Great review

@d3adlyz3bra 11 ай бұрын

just started the process for the 556k

@slyleprecon5521 11 ай бұрын

Sooo excited!

@michaeladams8992 8 ай бұрын

Awesome

@acevent5759 3 ай бұрын

Nobody ever talks about accuracy with the can. I have the Wilson Combat whisper suppressor, and I gain accuracy through it. As a hunter that’s pretty important. I’m interested in buying this canned if I’m not gonna reduce accuracy at 300 yard shots.

@mrcookiemonster7805 3 ай бұрын

And what about using the Flow 762Ti with and adjustable forward venting gas block? Where gas coming back into the firearm is reduced by venting excess gas out the front of the gas block. Do you think there would be any advantages like maybe keeping the Flow cooler under high rates of fire? Or disadvantages, maybe needing to re-tune the gas block bleed off?

@illestdomer2005 11 ай бұрын

Got it on that Rattler making me want to spend money that I shouldn't.

@michaelaustin4650 11 ай бұрын

Awesome video. I’m actually looking into making my first suppressor purchase to run on my MK18 as my duty rifle. Is there any can you’d recommend over the HUXWRX 556K? I’m open to anything. Suppression is huge for me but I also understand you can only get so much suppression with 556. Any insight would be great!

@Capitolarmory 11 ай бұрын

There's a lot to discuss, we're happy to do it over the phone. It really depends on individual needs. For work uses, my opinion is low backpressure and flash suppression are more important than dB reduction. You want to minimize collateral hearing damage, but it could also be a two-way range. (Surefire for example is a bit more loud, but excels at flash reduction and is lower backpressure.) The MK18 is overgassed, or overgassed and then some, depending on the version and gas port size. For work related uses, the Flow 556K is a solid option. You are correct in that 5.56 can only suppress so much. There really are a lot of good options you can't go wrong with though.

@tonygomes3617 11 ай бұрын

Get the flow 762 can and you will be able to use it on more stuff

@kennykrabss 9 ай бұрын

PEW Science

@mojo4376 6 ай бұрын

Anything Surefire

@wildcat8598 6 ай бұрын

Depends on what all you use. If you use primarily 556 than get a dedicated 556 can. If you plan on only getting one can your entire life than get a 30cal can in case you wanna run it on other stuff. As far as 556 cans go there’s no subsonic rounds so you can get decent sound suppression but mainly you’ll want first round flash suppression. Surefire does great with that as well as the SilencerCo Saker 556. On a MK18 (D I rifle) your gonna have gas in your face which is what helps with these flow cans. Just like everything in the 2A community there is ups and downs with everything and can’t have it all with just one thing which is why you get what’s best for you. Me personally I rarely shoot anything other than 556 so I got the Saker 556. I also got a 9mm can cause I run 9mm secondary and wanted to run 300blk eventually and the 9mm can handles 300blk subs so that solved 3 calibers and the 3 that I run. I eventually want a 30cal can cause I’d like to have a AR10/308 some day

@BasementOps 11 ай бұрын

Review on the Alaskan 360?

@John-ro3vu 11 ай бұрын

Are these going to be for sale on your website soon? I went to buy one and could not find one.

@Capitolarmory 11 ай бұрын

They are! They went live Monday at 10am

@logandutton 2 ай бұрын

Would this be a good fit for my LWRC m6ic di?

@johncrabill7140 7 ай бұрын

Nice can.

@mjay7238 10 ай бұрын

Will this fit on a zpap92’s fat muzzle !

@anthonybravo5176 11 ай бұрын

What brand of shirt is the capitol armory guy wearing?

@DesertMariner2007 2 ай бұрын

Noveske Rifleworks

@Yisunsin007 8 ай бұрын

What happens if you get a baffle strike? 🤔

@wildcat8598 6 ай бұрын

I would imagine one would be screwed. Depending on how the warranty and customer service is but can’t be just replacing a baffle right? One downside about sealed cans

@JNOSNOW 5 ай бұрын

Pretty simple, chop the end the core it out and re-weld a new 3d printed core in.

@rascaille3792 11 ай бұрын

Cool, I would imagine it's not great for subsonics but great for everything else

@deadbrocks 11 ай бұрын

Why would it not be great for subs?

@glaw9583 11 ай бұрын

Go watch Bauer precisions video on it. He does some subs and it actually performed surprisingly well

@12cc90 11 ай бұрын

@@deadbrocks As a rule of thumb, the internal geometry of these flow-through suppressors (CGS, SiCo Velos, Huxwrx, etc) is utilized most efficiently at the higher pressures from supersonic loads. Imagine holding the suppressor up to your mouth and blowing through - most of the air will go through the .30 cal bore down the centerline of the suppressor. Now imagine having a tank of compressed air being blown into the suppressor - there's enough air pressure and volume that it's forced to utilize all the complex flow pathways built into the suppressor. Not the perfect analogy, but it illustrates the point. There are outliers though, I think one of the CGS cans absolutely spanked a .300 Blackout subsonic test with PEWScience.

@BossHugo84 11 ай бұрын

But Does it Work With Sub 300 Blackout ?

@SouthWestGunnerOfficial 11 ай бұрын

Who cares. Buy a better can and most likely for less.

@calebclark6739 11 ай бұрын

Why wouldn’t it ?

@12cc90 11 ай бұрын

@@calebclark6739 As a rule of thumb, the internal geometry of these flow-through suppressors (CGS, SiCo Velos, Huxwrx, etc) is utilized most efficiently at the higher pressures from supersonic loads. Imagine holding the suppressor up to your mouth and blowing through - most of the air will go through the .30 cal bore down the centerline of the suppressor. Now imagine having a tank of compressed air being blown into the suppressor - there's enough air pressure and volume that it's forced to utilize all the complex flow pathways built into the suppressor. Not the perfect analogy, but it illustrates the point. There are outliers though, I think one of the CGS cans absolutely spanked a .300 Blackout subsonic test with PEWScience.

@illestdomer2005 11 ай бұрын

Not as well as other cans, I would assume. Pew Science ratings on the HX-QD 762 are pretty poor (relative to other less expensive options) on 300blk compared to 308 supers.

@scottloftin1730 11 ай бұрын

Get the OSS Helix. They just work, titanium and cheaper.

@calebclark6739 11 ай бұрын

Come on. For $1500 it should come with 20 stickers Lol

@Capitolarmory 11 ай бұрын

Do you want 20 stickers?

@calebclark6739 11 ай бұрын

@@Capitolarmory Yes !!! Lol

@pilotincommand85 11 ай бұрын

What makes this titanium different than any other titanium used on other cans? Seems you are suggesting this suppressor can be used with super aggressive rates of fire on semi auto or full auto how ever I want..where other titanium cans often caution against getting the body heat soaked beyond ~800ish degrees..are those companies full of it or is hux not being totally honest about their performance? I would legitimately like to know I can a couple of the what you call “other” brands of Ti cans..have I been too conservative with them up to now? Or can I use and abuse them like you seem to suggest I can with this Hux?

@SouthWestGunnerOfficial 11 ай бұрын

They wont answer. Allow me. Titanium is a terrible source of material to use on suppressors. I assure you it cant handle full auto fire. I also assure you this can sounds like ass. Dont waste your time/fall for the snake oil. Huxwrx is hype train. People push these cans because they are easy to sell but majority of these FFLs pushing the product the employees dont have them on their guns. Speaks volumes. Plus a msrp just shy of 1700 bucks is fucking insane. Literally can buy a surefire or something that suppresses really well and have money left over.

@pilotincommand85 11 ай бұрын

@@SouthWestGunnerOfficial thanks for the reply..I currently use surefire and love them..I have their 7.62Ti for bolt guns but looking for something that allows AR10’s to run better..I reluctantly am looking at these but I have definitely zero interest in another Ti can..no thanks. I thought it funny the every other maker says don’t get the can hotter than 800 degrees and then you see this. Passes 6x socom stress test..they also cooled it to 120 degrees in between each attempt..lol so you did it once on 6 occasions..got it

@mexicangator 11 ай бұрын

Huxwrx 556 flow is not a gimmick barrel and hatchett run it; the technology is legit; the titanium though I agree I’m still on the fence

@SouthWestGunnerOfficial 11 ай бұрын

@@mexicangator id say its somewhat gimmicky... at least a little. When your company needs all the gun bunnies, mike glovers, and influencers to tell everyone to buy the shit i always know that product is probably ass. Surefire suppressors and other big name manufacturers let their cans speak for themselves. Just sayin. I dig the idea of the huxwrx but it definitley doesnt suppress anywhere near as good as its competitors and the price tag is absolutley Atrocious.

@mexicangator 11 ай бұрын

@@SouthWestGunnerOfficial I respect your opinion but the price is nearly the same. RC2 is 1079 and you don’t get a muzzle device with the can which is an extra 150-200 dollars and the 556 flow is 1125 with a muzzle device so it’s a push

@MyCoolFish 21 күн бұрын

The hot dog

@vernehughart3546 8 ай бұрын

Wish they were legal here

@BlueMushroomSmurfCat 16 күн бұрын

The tax is crazy too well not that bad but here it’s 200 dollar tax

@superboy305 11 ай бұрын

Just wanted to it on a rattler, thanks

@malcolmpalm 11 ай бұрын

I really wish these had QD options

@JohnZ556 11 ай бұрын

It takes less than 5s to un/install. The muzzle device is an integral part to direct gas outwards into the channel. So you can only have an omni directional muzzle that's kinda big, no matter who makes it. The 17-4 muzzle device also acts as a sacrificial baffle, even more necessary to the Ti cans I would bet.

@malcolmpalm 11 ай бұрын

@@JohnZ556 I hear ya. I have a lot of pews that are pinned/welded with DA, or SCo muzzle devices.

@calebclark6739 11 ай бұрын

Why ?

@jaredandrews379 10 ай бұрын

Why do you need to take it off so quickly?

@zell666hell 5 ай бұрын

My friend 3D prints silencers for dirt cheap

@BlueMushroomSmurfCat 16 күн бұрын

Is that even legal?

@rx7addict Ай бұрын

It's not zero back pressure

@MyCoolFish 21 күн бұрын

You guy’ses ≠ Texan

@NoGoBu 20 күн бұрын

Way way to damn " expensive " of course, the snobs that spend daddy's money 💰 will say I'm wrong. 🙄

@StEvEn420BrUlE 7 ай бұрын

One thing worth noting is that for subsonic ammo, flow through designs are much louder and may have a harder timer cycling it compared to traditional baffles