HVAC Service Call: Centrifugal Exhaust Fan Making A Lot Of Noise And Not Working Properly (ABB VFD)

No video

HVAC Service Call: Centrifugal Exhaust Fan Making A Lot Of Noise And Not Working Properly (ABB VFD)

Рет қаралды 8,610

Күн бұрын

HVAC Service Call: Centrifugal Exhaust Fan Making A Lot Of Noise And Not Working Properly - Repaired / (ABB VFD) / HVACR (Heating, Ventilation, Air Conditioning/Refrigeration) Service Call: Commercial Kitchen Exhaust Fan Making Noise (Centrifugal Exhaust Fan Maintenance/Repair) Exhaust Fan Cleaning / Exhaust Fan Maintenance / Exhaust Fan Repair / Exhaust Fan Installation / Exhaust Fan Making Noise / Exhaust Fan Not Working / Exhaust Fan Making Loud Noise / Kitchen Exhaust Fan / Exhaust Fan Belt Installation / Exhaust Fan Belt replacement / Centrifugal Downblast Exhaust Fan #HVAC #ExhaustFan #JumperManTech
GoPro HERO8 Black (Camera Used In This Video)
amzn.to/3q4FmEz
Veto Pro Pac TECH MC
amzn.to/3gURJyZ
EPAuto Socket Set
amzn.to/4crx0e2
Wire Brush for Drill Set
amzn.to/3VX4HhO
Fluke 902 FC HVAC True-RMS Clamp Meter
amzn.to/39wvwiK
Fieldpiece ADK7 Deluxe Silicone Test Lead Kit
amzn.to/3VNYXDv
Klein Tools ET600 Megohmmeter Insulation Tester
amzn.to/409iNvu
Supco M500 Insulation Tester/Electronic Megohmmeter
amzn.to/42oy0ua
Fluke 1AC-A1-II VoltAlert Non-Contact Voltage Tester
amzn.to/3FcWElQ
Fieldpiece JL3KR4 HVACR Charge Kit (Digital Gauges/Probes)
amzn.to/3E4W0Fr
Fieldpiece SPK2 Folding Pocket In-Duct Thermometer
amzn.to/3mi8Fih
Fieldpiece SPK3 Folding ROD Dual Temperature Thermometer
amzn.to/3FbDufQ
Milwaukee M12 2-Tool Combo Kit 2598-22
amzn.to/3CtCRNC
Milwaukee Cut 1 Dipped GLOVES L
amzn.to/3s8H18O
Milwaukee 2351-20 M12 LED Stick Light
amzn.to/3rVJKEK
Milwaukee 48-22-1985 Fastback Hawk Bill Folding Knife
amzn.to/3e53ygW
Milwaukee 48-22-1500 Fastback Compact Folding Utility Knife
amzn.to/3qazJkC
Milwaukee 48-22-4041 Iron Carbide Core Large-Looped Jobsite Scissors
amzn.to/32fxC6I
Milwaukee 4932459097 Billet Torpedo Level
amzn.to/30Dh6Nw
Milwaukee Wide Blade Magnetic Tape Measure 16 FT
amzn.to/3yEN7kL
Milwaukee Fine Pt. Markers Black
amzn.to/3e4fH5W
Streamlight 66604 MicroStream USB 250-Lumen Rechargable Pocket Flashlight
amzn.to/320XiEF
Klein Tools 11-in-1 Screwdriver / Nut Driver
amzn.to/3s3o8ql
Klein Tools 32561 Multi-Bit Screwdriver / Nut Driver 6-in-1
amzn.to/3e4ur4x
Klein Tools 32807MAG 7-in-1 Nut Driver, Magnetic Driver
amzn.to/321n4bW
Klein Tools 600-4 1/4-Inch Keystone Cushion-Grip Screwdriver
amzn.to/3J11hS1
Klein Tools 32581 4-in-1 Electronics Screwdriver Set
amzn.to/3yEj3WC
Klein Tools LLK12 L-Style Hex Key Caddy Set 12-Piece (Metric/Sae)
amzn.to/3yRUiGJ
Yellow Jacket 18975 Charge Tool
amzn.to/3J4pfvJ
Yellow Jacket 60613 Service ratchet Wrench
amzn.to/3E8iYeZ
Yellow Jacket 19173 5/16" Female Quick Couplers x 1/4" Male Flare
amzn.to/3q0TQ4M
Cooper Bussmann BP-FP-2 Cartridge Carded Fuse Puller
amzn.to/3e0USrY
Crescent 2 Pc. X6 4-in-1 Black Oxide Spline Ratcheting SAE Wrench Set
amzn.to/3qqKlw7
Crescent 4" Adjustable Cushion Grip Wrench
amzn.to/3J4qsmL
Knipex 09 08 240 SBA 9.5-Inch Insulated Ultra-High Leverage Lineman's Pliers (1000v)
amzn.to/30EQmw5
Knipex 09 11 240 9.5-Inch Ultra-High Leverage Lineman's Pliers with Fish Tape Puller and Crimper
amzn.to/3H9iYAu
KNIPEX Tools - Long Nose Pliers With Cutter, 1000V Insulated
amzn.to/3e3IEi7
KNIPEX Tools - Long Nose Pliers With Cutter
amzn.to/3gUSE2i
KNIPEX Tools 98 62 02, Flat Nose Plastic Pliers 1000V Insulated
amzn.to/3p6lFsZ
KNIPEX - 74 08 200 - High Leverage Diagonal Cutters, 1000V Insulated
amzn.to/3mh8K5U
KNIPEX - 74 01 200 Tools - High Leverage Diagonal Cutters
amzn.to/3F1VScb
KNIPEX Tools - Cobra QuickSet Pump Pliers, 1000V Insulated
amzn.to/3sftr5Q
KNIPEX Tools 3 Piece Cobra Pliers Set
amzn.to/3FbRwy7
KNIPEX Tools Pliers Wrench 3-Piece Set
amzn.to/3nnRLfW

Пікірлер: 60

@steveweld5573 4 ай бұрын

This new building is lucky to have you there and the same for the hotels you service. When I was an engineer back in the day, I wish I had your help. Thank you for all you do and the videos you produce.

@JumpermanTech 4 ай бұрын

Thank you for that! Really appreciate this comment. As long as your building paid their bills, I would have loved to help 😂 Thank you for watching as well. Stay tuned for new videos every week! 🔧⚡️🙏

@sherwinalvarez7365 4 ай бұрын

Lol. Me and my helper were just talking about changing belts. Hey, when i 1st heard that belt, i was thinking that the pullys were too tight.

@JumpermanTech 4 ай бұрын

I hear that! I thought of that as well, but it was the belt being too dry and worn out. The other guy said all is fine, but clearly, it wasn't. We all learn something new every day! The new belt with belt dressing made a huge difference, and it will really preserve that belt. Always nice to have a spare as well. Thanks for watching as always! 🙏🔧⚡️

@gantmj 4 ай бұрын

I've heard that same belt noise from things on autotensioners. The belts look fine but sound like they're too tight. You make sure the tensioners work and just replace the belts and the noise goes away.

@ronnym1977 4 ай бұрын

Your knowledge of troubleshooting and general function of HVAC and refrigeration is quite impressive.

@JumpermanTech 4 ай бұрын

Thank you very much Ronny! Much appreciated. It didn't come over night! I been in the field since 2011 and I'm constantly studying even now. Thanks for watching 🙏🔧⚡️

@andyjones7836 3 ай бұрын

That has got to be the cleanest plantroom you have worked in 😮 good job 👍

@logicaljuan 4 ай бұрын

Over greasing is practically as bad as under greasing. It causes greater friction/heat which will kill the bearing life. Additionally, it appears like they may have mixed greases. Mixing incompatible greases breaks down the viscosity of both greases which will also create more friction and kill bearing life.

@logicaljuan 4 ай бұрын

They should go ahead and buy replacement pillow block bearings because they will likely need them before too long. And purge the greases lines when they do with poly Rex em.

@hmrody 4 ай бұрын

I am wondering if the noise was a worn sheave/pulley, misalignment or since the dufus before you jacked things up, even the wrong belt. I am far from an expert, but to me, it sounded like the the belt grabbing the pulley.

@billyhorton5779 4 ай бұрын

Thanks JMT and your apprentice, I bet you guys are a blast to work with!

@JumpermanTech 4 ай бұрын

You're very welcome & thank you! Totally a blast to work with. Good vibes and A+ effort. Thanks for watching Billy! 🙏🔧⚡️

@jasonjohnsonHVAC 4 ай бұрын

We use Polyrex grease on our motors ( non cooling tower ) they way over greased that sucker and blew out the seals. With normal maintenance...should be 2-3 pumps of grease maximum every 6 months. You can actually figure out the correct amount by using the timer on the VFD. It has a run time counter that can be reset for maintenance. The manufacturers provides a chart for how much grease for how much runtime. Those bearing seals are toasted. I take care of some really large fans, especially for stairwell pressure fans. We have one building where the exhaust fans are over 10' tall and the fan is over 6' in diameter. Just did some maintenance on the parking garage exhaust fans at the TX state capital building. They are Flakt fans and the motors are 100hp and the fan blade diameters are 8' each.

@stevencossaboon3237 4 ай бұрын

Nice work as always Jumper Man. They probably blew the seals out of the pillow block bearings.

@JumpermanTech 4 ай бұрын

Thank you Steven! There's a good chance of that. Might be time to change them before there is a disaster. Thanks for watching as always! 🙏🔧⚡️

@aliso-pv7ll 3 ай бұрын

Dear Jumper man Tech: “You pay peanuts you get monkies!” Changing the other guys diapers makes you money.

@oldmetalguy4577 4 ай бұрын

"spare me in the comments" LOL! Because the Karen who will bitch about rolling the belt off has never, ever , ever done that. Right. You're almost to 100k, Good work!

@JumpermanTech 4 ай бұрын

😂😂😂 Facts!! Almost🙏 Its been my goal to get 100k and get the youtune plaque. Been working hard for 5 years with the videos and I'm almost there. Thank you brother 🙏 & thanks for watching! Always appreciate your support 🙏🔧⚡️

@chris84662 3 ай бұрын

Belt Dressing for the win.

@himrfreeze 4 ай бұрын

Nice job as always

@JumpermanTech 4 ай бұрын

Thank you!! 🙏🔧⚡️

@NROhvac 4 ай бұрын

Leave a note on the EF for the maintenance guys saying “3-4 pumps of grease, THATS IT” My co worker does like 10 pumps, I tell him all the time you need only 3-4, every bearing he touches he over greases

@jorgeuribe4512 3 ай бұрын

I work in a hospital. And as soon as I heard the noise I knew what was wrong with the fan. We have 4 in house techs and management doesn’t understand that over grease kills bearings. They want to see grease coming out of it

@you166mhz 4 ай бұрын

good call ...

@JumpermanTech 4 ай бұрын

Thank you!! 🔧⚡️

@scottmaz4063 4 ай бұрын

Wow easy fix today well done JMT

@JumpermanTech 4 ай бұрын

Facts. Easy but very necessary. After that, there was 2 heat pump service calls in the building. Thanks for watching! 🙏🔧⚡️

@jrh86 4 ай бұрын

Poetry in motion 💯👍👍👍

@JT-qf4it 4 ай бұрын

Belt dressing is only a temporary fix in most cases. It gets flung off the belt and causes a mess. I have seen belt dressing break down the rubber belt destroying it. It's better to clean the sheaves and replace the belt with a new one.

@Eddy63 4 ай бұрын

Very good job with great tech tips ... Good little helper with you as always ... Thx JMT

@JumpermanTech 4 ай бұрын

Thank you! Those tips definitely come in handy. Facts. He's always there when I need him. You're very welcome & thanks for watching! 🔧⚡️

@kennethlobo4420 4 ай бұрын

Great video thanks for the tips on Greasing

@JumpermanTech 4 ай бұрын

Thank you & for sure! Any time 🤙🔧⚡️

@JumpermanTech 4 ай бұрын

Thank you for your support 💯

@Nighthawke70 3 ай бұрын

The pulleys are grooved badly, that grating sound are the pulleys being worn down. You don't need gunk for this issue, you need new pulleys. Get the correct set and retain the keys. Oh, and replace the pillow blocks because the grease they used may be the wrong type for this and flushed out the grease that is rated for this. Not to mention blowing out the seals on the bearings. Check pulley alignment and belt tension according to the manufacture, and I'll assure you it won't fail on them for 5-10 years of proper maintenance.

@jrh86 4 ай бұрын

Yeah missing and incorrect screws plus over greasing is always a red flag.

@JumpermanTech 4 ай бұрын

💯💯💯

@armandotorres626 4 ай бұрын

Greasing bearings is a gray area out there.... What's too much, what's not enough, how frequent to grease.... Should get rid of all greasable bearings... When they go bad, just replace... Removes user error from the picture...

@JumpermanTech 4 ай бұрын

It is definitely a grey area. Greaseless bearings would be awesome. Facts. Thanks for watching! 🙏🔧⚡️

@ILoveKittys78 4 ай бұрын

😻💚💜💚

@JumpermanTech 4 ай бұрын

💜🔧⚡️

@chesterguerrero8312 4 ай бұрын

Im confused, i assumed you did exhaust fans like this before in your career. Sounded a bit like a 2nd year apprentice. Belt dressing was recommended to not be used by Browning. If you got a sqeeky belt you can check your pulleys and tension. If your snapping belts on and not checking your alignement. The 3/8 screws do come with the unit as well as the metal tabs they have for the screws.

@chesterguerrero8312 4 ай бұрын

Lastly the panel has a side were 2 screw holes are closer together those belong on the back so the cover was backwards.

@zekenzy6486 4 ай бұрын

Great video as always. Good Job and Nice Work. Thank you for sharing. Have a nice weekend ^_^

@JumpermanTech 4 ай бұрын

Thank you! You're very welcome & thanks for watching. You also have a nice weekend 🙏🔧⚡️🤙

@chrissmith513 4 ай бұрын

Bet those bearings are shot ! 😊😊😊

@JumpermanTech 4 ай бұрын

There's a good chance! Might be time to change them before there's a "nightmare" title video recorded 😂 Thanks for watching! 🔧⚡️

@robertdavenport9095 4 ай бұрын

Exactly how we do it in the field

@JumpermanTech 4 ай бұрын

💯💯💯

@JumpermanTech 4 ай бұрын

Thanks for watching! 🔧⚡️

@jacecoleman3832 2 ай бұрын

So just for future reference take off the belt if it’s squeaky like that and you are wanting us the viewers to here the motor personally I could not here the motor as the belt squeaking was louder than the motor

@thesilentonevictor 4 ай бұрын

Too easy for the professional jmt st your service

@JumpermanTech 4 ай бұрын

Haha thank you & thanks for watching 🙏🔧⚡️ Always appreciate your support. I try my best when I do service. Enjoy your weekend 🤙

@johanea 3 ай бұрын

Self-tapping screws is just such a cheap and bad solution by the manufacturer. And yes, the one who did the job before, he should maybe reconsider his occupation and start to flip burgers instead.

@genewheeler6320 4 ай бұрын

Bro.😢 clean the pullies as well. With all that grease it prob got on pullies and dried up

@JumpermanTech 4 ай бұрын

Facts, it did. When we cleaned the unit, we also cleaned the pulleys 👍 Thanks for watching! 🔧⚡️

@genewheeler6320 4 ай бұрын

@JumpermanTech ooo sorry bro missed that If figured you did. As thorough as you are

@JumpermanTech 4 ай бұрын

@genewheeler6320 It's all good. I'm with you on this one. That part wasn't actually in the video to spare the viewer of simply cleaning. Haha thank you! Enjoy your weekend 🤙🔧⚡️