HYDRAULIC PRESS VS MOST EXPENSIVE WRENCHES

Рет қаралды 34,648

Crazy Hydraulic Press

Жыл бұрын

With the help of a hydraulic press, we will test the most expensive wrenches. Milwaukee and Wera

Пікірлер: 91

@MikeGroves Жыл бұрын

It appears that when your hex bar bends downward under load, the force of the press isn't purely at right angles to the wrench any more, causing some to twist the handle, since the flat is not near as strong as the edge on a wrench. Support the hex bar before and after the wrench for more accurate distruction measurements.

@lucarambaldi2731 Жыл бұрын

ESATTO 👏👏👏👏👏

@WontSeeReplies Жыл бұрын

True. But you won’t experience these loads without a breaker bar. A breaker is never centered. This is a good test exposing wrench steel weakness. Furthermore, most wrenches have a canted box end. Meaning they’ll experience the torsion either way.

@spercwolf2985 Жыл бұрын

I was going to say something able the hex bar. Because it is so far out, the bend in the hex bar is an added variable to this equation. Plus, we're all the wrenches place at the exact same point on that bending hex bar? I am glad to see Milwaukee at the top of the chart though. They make very good tools.

@Alestomis Жыл бұрын

Am I the only one who actually sees that the Wera is probably the best out of all of those wrenches??? It is the lightest, and it has 30-degree steps on both ends. NOBODY will push or pull 330kg on it ever!!! It snaps because it is made of hardened steel. Those shitty soft steels used on the first 4 wrenches mean they will wear off very quickly and in time would damage the bolts/nuts. The second place in my opinion is Milwaukee. All others are rubbish. Obviously, the test wasn't about the overall quality. But when I read some comments about how Wera is bad I couldn't resist to write something.

@markanthonystringfellow3923 Жыл бұрын

Just 1 thing to consider, Hardness in the 48/55 hrc class will be more brittle but for low torque fastners and rusty/rough surfaces the harder spanners dont wear and round off as much, same with Joe X who tests knives, soft steel will be tough but wont hold a wear resistant cutting edge for peanuts, Horses for courses :-)) Your mileage may vary :-))

@terrygee210 Жыл бұрын

Interesting to watch, but for a proper comparison the hex bar should be supported at both ends to stop depression, and test the open ends too!

@morganmccauley1687 Жыл бұрын

A very interesting test. Well done.

@Stu_2112 Жыл бұрын

Interesting, but ultimately I'm not sure if it is particularly relevant when buying your tools. The likelihood of you exerting that much force on a spanner is low. Whereas the requirement for accurate machining of the contact surfaces and dimensional accuracy is far greater. I use Wera Joker spanners and find them very good on the metrics that make a good spanner good. I dont fear shearing the head off the spanner under normal use

@tsherwoodrzero 9 ай бұрын

This is an excellent test. Dimensional stability under load is the entire point of a wrench/spanner. Imagine you're trying to crank a nut or bolt and the wrench goes Play-doh on you, opening up by 3mm. and chewing the corners off. I had that happen on a BMW fan clutch wrench. It survived ONE use. I'm reasonably strong, but it was nowhere near the force one would think is needed to distort a wrench. The second time I tried to use it (earlier today), it wouldn't hold. One jaw was bent outward and the tips were 34.8mm apart instead of 32. And since the jaws weren't parallel anymore, there's no Macgyvering it to work since the torque delivery surfaces aren't in phase anymore. Trust me, I tried. It was just too far gone because the metal was too soft when it was made. So it got marked with SchieBe. because that's what it is.

@softwarephil1709 4 ай бұрын

Clear winner. I put that much torque on wrenches every day. 😂

@sarcasticguy4311 Жыл бұрын

I would've liked to see a SnapOn wrench.

@andre_s. Жыл бұрын

Würth ist kein Hersteller sondern Händler. Die kaufen Werkzeuge und lassen ihren Namen Aufdrucken. In der Praxis aber mehr als ausreichend, hab noch nie ein 17er Schlüssel mit der Hand abgebrochen... 😅

@BradleyHoff-ck5kw 5 ай бұрын

Love it

@JanForsker Жыл бұрын

That broken german wrench named JOKER...it says all 😂

@andrewryder3276 Жыл бұрын

The problem is it ISN'T German. That wrench (although a German "brand") was made in the Czech republic!

@user-rs8rb3tv7y Жыл бұрын

I would be interested to see how the more expensive/professional wrenches from the United States. The low end in cost would be S&K, Craftsman, Mac, and the most expensive would be Snap-On. Please do a video showing those brands.

@jamiemorgan4146 6 ай бұрын

Also Proto ! Not Craftsman anymore. ( idiots ) They’re made in China now.😂 He could test a USA Craftsman though.

@anshbabyt Жыл бұрын

Best hydraulic press channel in the world 🌎🔥

@yourmomissus7179 Жыл бұрын

🔥🔥🔥

@cokezero1 Жыл бұрын

You should do various tools of Milwaukee vs dewalt

@WontSeeReplies Жыл бұрын

How? It’s a press channel. DeWalt and Milwaukee are know for power tools, not wrenches. Well…apparently Milwaukee is??

@robertwootton2161 Жыл бұрын

Bar needs support

@scamazoncrime5165 Жыл бұрын

😂 it collapses and the machine gets rocked

@Av3rjkRRow Жыл бұрын

making some cool offset wrenches i see lol

@Rorimac67 Жыл бұрын

I take the 4$ from Wurth. I will surely not apply >500kg of pressure with my 80kg bodyweight.

@testeteste8238 10 ай бұрын

Faz o teste com a Belzer.

@cjackson7089 Жыл бұрын

the music grips me as much as the video content

@electricaltechnology2864 10 ай бұрын

Tvrdost klíčů nebo ořechů je priorita a WERA krásně střelila je nejlepší, pružné se velice rychle opotřebují, vytahají jsou potom k ničemu a tento test mi jen potvrdil že pružný vydrží větší tlak, ale to je právě špatně my mechanici víme lepší když praskne než se vytahá a musíš je vyhodit, naše TONA je také tvrdá vydrží věky ale je také drahá.

@JustAnAverageGuyToo Жыл бұрын

Do you guys live in Finland?

@CrazyMurphy 10 ай бұрын

Wera is a subsidiary of Bitburger Holding. And Bitburger also produces beer in Germany. In addition, production from Wera would be relocated to the Czech Republic. That's why it's not Made in Germany.

@ivan-Croatian Жыл бұрын

Why is there NO Unior????

@taftancastingchannel Жыл бұрын

Like 👍

@SinanTosun 7 ай бұрын

Can you test IZELTAS? İzeltaş is very high quality Turkish manufacturer. Please test it with other manufacturers.

@marksmithson1414 Жыл бұрын

Really cool video of which one was the strongest wrench

@stever7638 Жыл бұрын

What about Craftsman, Matco, Mac, Snap-On? Cool vid though.

@dustinnance3163 Жыл бұрын

Milwaukee, USA, baby

@TundeEszlari Жыл бұрын

I love your videos, can I get a comment heart?

@marcoscastano Жыл бұрын

❤😂

@lucarambaldi2731 Жыл бұрын

NO 😢 PURTROPPO ABBIAMO TERMINATO I CUORI ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤😂😂😂😂😂😂😂😂😂🎉🎉🎉🎉🎉

@333ug Жыл бұрын

Würth is Made in Taiwan. I See it in Tage Box

@mikerope5785 Жыл бұрын

halfords professional from UK

@misterwirez7731 Жыл бұрын

Not sure about the starting angle of the wrenches. Milwaukee/USA is for sure the winner. It seems some mfg's harden the ends mostly but Milwaukee and the one German wrench temper the entire piece, with the most expensive being the most brittle. Maybe it was tempered too much. Still the Milwaukee @ $17 seems expensive, but is it? Overall for Joe homeowner, all but the last one is probably capable enough for ordinary/general use at home.

@mikaelandersson1288 Жыл бұрын

Milwaukee USA is in fact manufactured in Solingen, Germany. German steel is still the best as it has been since the late 18th century where it stole the crown from Toledo, Spain.

@GM-ih7wi Жыл бұрын

Try Facom France.

@BobbySacamano Жыл бұрын

"Drop forget China" I cant figure out if this is a bad translation or a straight up diss. Like, "bought a tool from China? Dropped it? Forget it."

@mikaelandersson1288 Жыл бұрын

I think he means drop forged whatever that is.

@sarcasticguy4311 Жыл бұрын

@@mikaelandersson1288 Yes, it's supposed to be drop forged but "drop forget" is unintentionally pretty damn funny.

@electricaltechnology2864 10 ай бұрын

Normálnímu člověku stáčí i ty nejhorší klíče znám takové lidi a nemají šanci je zničit, zato v servisu ti ani nepomůžou ty nejkvalitnější i kvalita při častém používání se zničí.

@glorygulbi Жыл бұрын

sure sure number1 tools made in USA verygood tools so i don't want anymore another country tools

@ws.safluk2325 11 ай бұрын

We have stahlwille

@leonardleonunu Жыл бұрын

So the expensive ones tend to fail by breakage rather than plastic deformation? I am not sure I prefer those more than one that bends.

@WontSeeReplies Жыл бұрын

You do.

@flyinryanfpv8763 Жыл бұрын

@@WontSeeReplies Having a harder wrench is better all day. Less chance of rounding out the flats and nobody wants a bent wrench (unless you do it on purpose for a reason). If it goes to those lengths it's time to replace it either way. But you'll get more force out the the Wera or Milwuakee without plastic deformation. Just not as tough overall if you plan to take it to it's breaking point.

@SiouplaitMerci Жыл бұрын

No facom !

@TMCORPTony Жыл бұрын

french ( FACOM ) 🚀

@WontSeeReplies Жыл бұрын

We Americans aren’t completely useless. Yet.

@mikaelandersson1288 Жыл бұрын

All Milwaukee products are manufactured in Solingen, Germany.

@BiggMo Жыл бұрын

🇺🇸

@tw5007 Жыл бұрын

Milwaukee 10mm Joker 6mm 🤷‍♂

@Tom-yo7zf 11 ай бұрын

You get what you pay for. Except with Wera

@itz_Alenfix Жыл бұрын

😱😱😱😱😱😱😱😱

@rangebhai90 Жыл бұрын

I love from India ❤❤

@timkbirchico8542 Жыл бұрын

hex bar flex ruins the demonstration.

@WontSeeReplies Жыл бұрын

Nope. Most wrenches today are not straight on the box end. This speaks for the quality of steel perfectly. And I’m an American who was hoping Wera won.

@dragon_slayerwtr1106 Жыл бұрын

LETS GO USA WHAT THE HECK IS A KILOMETER 🇺🇸 🇺🇲 🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🦅🦅🦅🦅🦅🦅

@ricardolizarraga7755 17 күн бұрын

Creo que muchos comenzamos a sospechar que trabajas para herramientas Milwaukee, que te pagan muy bien para desprestigiar a otras marcas, que vendes esas herramientas Milwaukee o que eres el dueño o accionista de la empresa que las fábrica 🤔

@Trumplican Жыл бұрын

the most expensive wrench you could find was 22 bucks? I'd like to see Snap-On, Mac, Cornwell, etc....

@ernie28ernie Жыл бұрын

-Stahlwille- ;)

@crandonborth 11 ай бұрын

Haha right!!! 1 Snap on Wrench is like $50 lol

@geronimo5537 Жыл бұрын

Yaaa America steel showing its strength!

@Artun_Mustafa Жыл бұрын

First

@prabh4764 Жыл бұрын

Pin plz

@zekeriyaylmaz665 Жыл бұрын

first comment

@averellrios4511 Жыл бұрын

P r o m o s m

@Reckless-mindfulness Жыл бұрын

I would gor for Chinese, no worry if you lose it in the garbage.

@philw8103 11 ай бұрын

lesson from this video, Wera is a complete rip off.

@kyphoenix83 Жыл бұрын

I guess German steel is not what it used to be

@mikaelandersson1288 Жыл бұрын

It's not german steel anymore... it's chinese shite.

@xXxDEMANJENIYAxXx Жыл бұрын

Lol That wrench is made in Czech Republic

@333ug Жыл бұрын

Wera dir sure Not Made in germany. Tschechische Republik

@outsider7658 Жыл бұрын

Ei tullut mieleen, että pitäisi tukea se terästanko, toisesta päästä? Nämä tulokset ova insinöörille, täysin mitään sanomattomia. Eivät pidä paikkaansa, koska "vääntömomentti" ei suuntaudu suoraan, kyseiseen avaimeen/miin. Uusiksi, kiitos ja tällä kertaa oikein.