Thanks for the info👈 😉

Yeah, maybe 🤔

that was the instructions straight from the mouth of a Hydro Gear rep when I replaced mine a few years ago

Appreciate it John 😉

Thanks! Appreciate the comment 🤜💢🤛

Thanks! Glad the video was helpful 😏👍

Just dropping knowledge for Mr. Mike 😉

We love the smooth ride of a Ferris 😉 Thanks for watching

Nice 😉👍

That’s why we do what we do! Thanks for watching!

jinkz58 this is our updated video when we changed it last kzfaq.info/get/bejne/eK-Ri7OpudnedYE.html

Good to know thanks 😉👍

Thanks 👊💯

Ha🤓thanks for watching!

Have fun with that Ben 😉 Thanks for watching

Glad you enjoyed the video🤔not sure what you mean about 3100's stoped working? Could be the hydrolic bypass valve stopping the wheel motors from working 🤷‍♂️

Glad you got something out the video. Thanks for watching Kim. Remember to check how much oil yours holds 😉

Will do my friend 👍👍

Thanks I'll probably be doing another video on this soon because, I didn't think that I explained the process as well as I could have 😬

@@JsCrazyCutzLLC 👍

Thanks for watching 👍

Yeah, that would make sense but, that's how it works on these 🤷

Thats very observant of you 😁☝️There is lots of beef for sure and some deer meat. We are carnivores you know!? It's somewhat organized and we will absolutely do a cooking video !

Yeah! I got some time on that mower for sure and It's not even 2 years old yet 😉

Thanks mang ! 😉

1 gallon in each wheel motor for the 5400 series

Thanks

Thanks man 😉

Ha 😀what a co-inki-dink a fellow car stereo installer😎👊yes it is an efi and yes it takes 2- 5 quart jugs (1 in each resivour)I pretty much guessed on the oil compacity but, if the oil starts overflowing out of the vent and your oill level is 1/4 of the way full in your resivours then your good 👍thanks for watching and commenting

I'm sorry ,I think you misunderstood me😎 The hydro oil had been changed 2 times prior to this video. I was talking about my tires on the mower. They had 900hrs on them and since I was removing them for the oil change ,I'd might as well get the tires replaced 🤔 I probably should have stayed on the topic at hand 😉

J's Crazy Cutz, LLC The thumbnail stated “hydro oil” so that’s where my attention was 😂. Thanks for responding. How do you change the hydro oil since we’re on the subject?

BJ G I have done a more updated video on the hydro oil change...it might give you more info on how I do it! kzfaq.info/get/bejne/eK-Ri7OpudnedYE.html

J's Crazy Cutz, LLC Thanks

I don't know why I do things the way I do Lol hope the video was helpful😎👍

Yep! Thanks for watching

Thanks for watching! Sorry but, I no longer own that jack anymore and I don't remember the model number. All I know is that it was $600 from the HOME DEPOT online store. I have been using an aluminum ATV jack. It's a much lighter manual version of jack from Harbor Freight about $200 and I prefer it much better.

The jack actually has solid steel wheels up front but, they are real small and it makes it a bit difficult to maneuver 😎...I love the 5400 Trans axles. They take 4 quarts of oil in each pump.

Sorry ,guess I didn't explain that. 13:50 That is how you release pressure from the hydro motors(by you turning it a quarter turn) you unlock the motors so, you can push or pull the mower around. If you don't unlock them, you can damage the pumps. This is also used to purge the air trapped in the system when changing hydro oil. In the video I turn the valves before changing oil,then I add the new oil and filters .I'll then purge the system by moving the control levers back and forth 4 or 5 times (while running) to get any air out that might be present . I'll then turn the valves back to stock position,lower the mower and drive it around to test it. Hope this helps.Thanks for watching.

Good video. First time I watched a full 20 minute how to video in a long time

@@danielsheets696 thanks 😎👍

That’s what I came into the comments to seen I’m like I know I didn’t miss any of the video!

I prefer the Vanguard the Kawasaki’s I have owned sucked gas

@@JsCrazyCutzLLC those cheap Briggs really suck the gas too.And most are on 5 gal mowers!!

I just watched yours again and yes that jack is slick. Think I saw some grey hair on u too.That cordless impact took lugnuts off good!! That whole garage looks setup for mower service!!

37 vanguard tomorrow!!!

Ha, only the mustang has a small aftermarket stereo system Lol ...yeah I was an installer for 10 years ,then I got into the👉 lawncare 👈🤣

It's quite possible.

Guess I'm just dumb like that 🤔

Lol. Fair enough.

One 5 quart jug in each reservoir 🤔 thought I mentioned it in the video 🤷

Good idea 💡

🤔Hmm maybe the bypass valve on the wheel motors isn't all the way in the right position or that the hydros has trapped air in the lines and need to be purged. I'd check that first then consult a dealer if that isn't the problem 🤷‍♂️hope you figure it out 😎

Thank you so much, really appreciate it.

Check fluid?? Belt? Air?? Pos of activation screw?

They have always seemed smooth to me. The Hydro-gear brand wheel motors aren't as sensitive to the touch as the Parker brand ones. It's all about preference.

@@JsCrazyCutzLLC I must have air that needs bled in the bypass mode plus I get a jerking uphill only remeber EFI and I still suspect air in hydros. You have to bleed in bypass first then reg.Its new but dealer is moving. Not in huge hurry.suspension seat any bump and you bump hydro levers. Wish I had got 4400 hydros just pull knibs

Ps dealer said they do also I have those 2 HUGE DECK belts. A lot of shit spinning. Wife found book belts on cutting deck 3yr/300 hr warranty

Prob buy a stihl ms250 there tomorrow to keep them happy. That will be my only stihl saw. They run good and 10 better on my back.

2:06 minute mark

So, I do this every year weather it needs it or not. I usually put close to 500 hrs per year on this mower. I also use the cheapest 20w/50 oil available. The oil doesn't look like it breaks down but, the main reason I do the hydro change is the filters🤷‍♂️ However,I prefer expensive oil for my engines😉 I would change the Hydros every 5 years if I were a homeowner whom only puts 100hrs per year. Hope that helps ! Thanks for watching

@@JsCrazyCutzLLC thank you I am a homeowner with 200hrs so I will go another yr

I know I should not use an impact on that cap but , I had it set on the lowest setting and I was just bumping the trigger🤷‍♂️probably should have used a torque winch ,I know 😉

It was 20/50 regular motor oil for these Hydro-gear 5400 trans axles

Good idea 👌

Rachet 😉got it 👍

My Son throws DeWalt impact to everything U need impact universal too and sockets. At least you do your own work!!

Even GM said for everyone to just tighten CV nuts about 120ft lbs. About like lugnut.Those wheel brgs did go out a lot. Always get the Tomkin or top of line. We put some cheap ones in were lucky to last a mo!!

If you use impact I'd be afraid of cracking 5400 case. Bet those are cheap.I hope it's nice and smooth. How long do u go on that 500 hr bs ??

The eng oil?? I've heard about 15 different answers

Yep!

Oil on the Trans? Look at your owners manual for what they recommend. But if I am changing the oil I would change the filters at the same time just to be safe.