No video

HydroDeck Foam Boat Turf | Full Install Tutorial

  Рет қаралды 126,487

Send It Jon Boats

Send It Jon Boats

Күн бұрын

Пікірлер: 261
@filipbruylant2021
@filipbruylant2021 6 күн бұрын
Nice job with those vinyl strips. They look really good but they also prevent water from coming in.
@SendItJonBoats
@SendItJonBoats 5 күн бұрын
Thanks! Glad you enjoyed the video
@luuk-out-below9804
@luuk-out-below9804 2 жыл бұрын
Glad to see you back on, thanks for the heads up on the cheap turf!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Been busy, many things going on with work and boat stuff. Going to try and get some videos out for ya'll over the next few weeks.
@jeremyswisher7403
@jeremyswisher7403 2 жыл бұрын
Thank you. Starting my 16ft Grizzly Project. Got the manual rivet gun, sander, 14gauge wire. Saving for the hydro decking. Looking forward to sending it.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Nice! Sounds like you got a fun project ahead of you!
@thomaswilson9792
@thomaswilson9792 2 жыл бұрын
Dude I literally had two rolls of that shit in my cart and was fixing to order you saved my ass this time
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yeah man, that amazon stuff is junk, don't waste your money.
@coltenboomgarden2428
@coltenboomgarden2428 7 ай бұрын
Just bought an old pos flat bottom and was very overwhelmed with how I wanted to set it up and repair it. Your videos took a lot of the questions away. Thank you!
@Aric--
@Aric-- 2 жыл бұрын
Yup. My favorite channel about boats.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thank you so much. Glad you are enjoying the videos.
@James_Hande
@James_Hande 2 жыл бұрын
Just recently stumbled across your channel, AWESOME info and videos!!! I used to fish from a canoe for most of my life. Now that I'm 63 with a blown out back I finally upgraded a bit. I don't own a Jon boat but picked up a 1978 Glastron Skiflite 16' Tri-Hull with trailer and 50hp Mercury really cheap. I'm rebuilding it, separated the 2 hull half's (top & bottom). When I get done replacing the transom, stringers and floor deck I was wondering what to use for the flooring cover. Thanks for saving my arse from buying the cheap crap. Oh yeah... I'm converting the boat from a bow rider to a fishing boat.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I made that huge mistake and bought the cheap turf... I regret it and will never do it again.
@flinginairos
@flinginairos 2 жыл бұрын
I'm new to your channel. This content is GOLD. Love the humor and the "Scooter" segments at the end 😂
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thank you, glad you enjoyed the video.
@tdwz1652
@tdwz1652 4 ай бұрын
"arrgghhhh, arrrrghhhhh" definitely sold me on that adhesive test haha
@user-nq4fe8br9v
@user-nq4fe8br9v Жыл бұрын
Trimming it out actually looks more professional. Great job.. Trimming it out actually looks more professional. Great job..
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Thanks, glad you liked it
@-krakk3rjack365
@-krakk3rjack365 2 жыл бұрын
I'll probably never own a Jon Boat but, I love watching your vids.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
You should get a boat... it's like the best money pit ever! Boat's N Hoes!
@-krakk3rjack365
@-krakk3rjack365 2 жыл бұрын
@@SendItJonBoats I'm in New Zealand, so Jet Boats are the thing. The ol' ball and chain, might be too happy about dem Hoes tho. LoL
@bob2161
@bob2161 2 жыл бұрын
Best Haterade corner in a long while! You had me laughing a few times there. BTW, thanks. You just saved me from a mistake. I had just about decided to order some of that ChinaTurf. I'll just wait a bit longer and order the good stuff. Keep on Sendin'
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Glad I could help. Save them pennies and get the better turf, it is well worth it.
@douglasdorsey4102
@douglasdorsey4102 2 жыл бұрын
Yeppir...always remember that China is VERY fragile with a high likelihood of BREAKAGE!lol
@addrulzamerica
@addrulzamerica 2 жыл бұрын
Best commentary ever. "It's bonded, James Bonded"
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I wondered if anyone was going to catch that... you are the first! Glad I could make you giggle.
@douglasdorsey4102
@douglasdorsey4102 2 жыл бұрын
Particularly enjoy your Scooter "expose' " segments! Not only do you sport a high velocity 1st serve but I enjoy your incredible "top spin" capabilities on your return. These scooters should, but definitely aren't capable of, realize the need to climb down from their self-assigned, elevated judge's chair! Your creativity and in-depth explanations are stalwart compared to most YT 'rs. Keep up the good work... maybe save your energies for your beverage "Power Jerk"! Although I do enjoy a competent Slam-down artist like you, let the attention-starved "Jerks" stay hungry! Lol x 2!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I just find it funny and I like to give the haters something to run their flappers about. Thanks for watching, many more to come.
@codysmith7456
@codysmith7456 2 жыл бұрын
This whole build is one of the dopest I've ever seen if you are ever in nebraska hit up the elkhorn or the platte river
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Cody. Doubt I will ever make it to Nebraska... ya'll got too much snow for me, us southern boys don't handle to cold too well.
@rickbos7164
@rickbos7164 2 жыл бұрын
I appreciate your opinions and honesty regarding your victories and failures on the endeavors most of us want to try but want someone like you to try first. I just got my first Send It tee shirt from The Jon Yacht, still looking for the sticker/decal for my jon boat. I'd rather give you money than "lift" your graphic.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Some body has to be the test dummy... might as well be me. We are working on the stickers, but you are more than welcome to use my logo if you want.
@nate4036
@nate4036 2 жыл бұрын
Trimming it out actually looks more professional. Great job.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thank you, i thought it was a nice touch on the cheap
@robertfoote3255
@robertfoote3255 2 жыл бұрын
Nice Shirt....Bacon Helps. If I had not already applied color matched bed liner to my top deck....that Hydro deck looks sweet! 🤔. The only thing I see is those cold days of spring Steelhead fishing...freezing water in and on it. 🤔 In the Sunbelt it's.... perfect! -17°F with 25mph breeze up here, every thing is froze solid.....we are playing go fish with cards.... inside! 😂😂😂 Even pointing out your mistakes.....I think it still looks great. SEND IT!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
whoooooooo yeah keep that -17 temp stuff up there! We don't want it.
@sampson583
@sampson583 2 жыл бұрын
Man u just saved me a lot of money. Had 4 rolls of the Amazon kind in my cart. Will be getting hydrodeck instead. Awesome video.
@SendItJonBoats
@SendItJonBoats Жыл бұрын
That amazon stuff really pissed me off. I tried everything I could to make it work and it would not stay stuck for nothing. Waste of money. I bought 3 boxes of that garbage for nothing.
@connorf7122
@connorf7122 2 жыл бұрын
love the effort you put into your vids!! keep up the great work!!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Connor. Appreciate you watching.
@guamtownbnt3102
@guamtownbnt3102 10 ай бұрын
Was wonderin y ur boat was wet when trimmin outside...thought u cleaned her off for the cam...till i watched the end😂😂😂😂....RAIN!!!NICE VID...
@kellihess2686
@kellihess2686 8 ай бұрын
Well done! If you want to fish for trout or smallmouth, let me know. Montana rocks!
@skxeta
@skxeta Жыл бұрын
I use the Amazon turf on the back of my speed boat and it’s held up really well although it isn’t very squishy but if you sand the area and prep it then it’ll last
@westte1417
@westte1417 2 жыл бұрын
Hey dude I wanted to say I really appreciate your channel, really helps us guys who are just getting started. I just picked up some Hydroturf from Facebook marketplace for pretty cheap, hope it does good for me. Also Roll Tide baby😬
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
You will like that Hydroturf it is good stuff. Geaux Tigers!
@skidmarkzuckerberg
@skidmarkzuckerberg 2 жыл бұрын
I actually have the Amazon stuff on my jon boat deck and it has held up pretty well given the quality. I painted the deck and lightly scuffed it before sticking it down and that seemed to help with adhesion. Surprisingly, the foam itself cleans off pretty well with dish liquid and a bristle brush. I will say though that it could be thicker stuff and have a bit better adhesive(clearly from your video) . My feet after standing barefoot for a couple hours need a break. With shoes or sandals no problem standing for however long. If I come to redoing the deck in the future, I would definitely splurge this time around on better quality foam but I think the Amazon stuff is a good option for those on a budget.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
First I have heard with good luck on that Amazon foam. The stuff I got would not stay stuck at all. It sucked. Glad your experience was better than mine.
@vinceperry7133
@vinceperry7133 Жыл бұрын
You're killin me smalls.... I don't have money for float pods,gator glide,hydro deck, I just wanna send it !!!
@SendItJonBoats
@SendItJonBoats Жыл бұрын
I dont have any money now either, because I sent it! LOL
@vinceperry7133
@vinceperry7133 Жыл бұрын
@@SendItJonBoats bro you send the shit out it ! Lol
@ronaldmitchell2565
@ronaldmitchell2565 Жыл бұрын
Love the videos… The scooter comments literally kill me…Lol 😢😂😂 😂
@SendItJonBoats
@SendItJonBoats Жыл бұрын
LOL, glad you are liking it. Thanks for watching.
@dcrcavazos
@dcrcavazos 2 жыл бұрын
Great job ! Love the look of the boat .I can't wait to build my 1969 John boat! You gave me the best red neck ideals!! Thank you
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Redneck engineering degree hanging up on my wall. Yee Yee!!!! Thanks for watching.
@ronbumgarner5479
@ronbumgarner5479 2 жыл бұрын
Very well done , and a damn nice Boat, thanks. Oh send It
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Ron, Appreciate you watching.
@joekeefer5236
@joekeefer5236 2 жыл бұрын
Another great informative video for us real guys
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Glad I could help. appreciate you watchin the video.
@ronbumgarner5479
@ronbumgarner5479 2 жыл бұрын
I can't stop laughing at the scooter thing, have fun and Well done....
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Glad I could provide some comic relief. Thanks for checking out the video.
@ronbumgarner5479
@ronbumgarner5479 2 жыл бұрын
I'm 63 years young, have a few jon Boats, love the fun and humor, I'm the same way..keep on rocking it..
@rexslay7264
@rexslay7264 2 жыл бұрын
Sweet man,you did a hell of a job
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Rex. Glad you enjoyed the video.
@mike-rp3pb
@mike-rp3pb 2 жыл бұрын
Good information, Thanks
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks for checking out the video.
@larrymoschenrose4038
@larrymoschenrose4038 2 жыл бұрын
Love your videos. Keep being you your awesome.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Larry
@electrickflame353
@electrickflame353 Жыл бұрын
Man this video was right on time! Now I only have to choose between Sea Dek or Hydrodeck
@cjwbii9495
@cjwbii9495 2 жыл бұрын
I love your videos man! I own a 19' off shore center console from the 80's that I've rebuilt from the ground up since I was 16. I fucking hate it and it is continuously rotting or breaking elsewhere. I want to get a jon boat and customize it to my liking and these videos are ridiculously helpful. Thanks again!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Awesome, glad i could help.
@hopefulboost9436
@hopefulboost9436 2 жыл бұрын
The haters corner is the best !👍
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LOL, Thank you. Everyone seems to be enjoying it.
@rodneymatthews3944
@rodneymatthews3944 2 жыл бұрын
Get u a heat gun and warm it up u can move it around but ur rolling pen is a very good idea
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Did not even think about a heat gun! Great idea.
@smokeshackmerica2722
@smokeshackmerica2722 2 жыл бұрын
Good shit as usual. Great idea on the trim
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks bud. Appreciate you watching the video.
@edstimator1
@edstimator1 6 ай бұрын
very good to know. I hate wasting my money on cheap knockoffs that fail.
@upsjetmechanic5647
@upsjetmechanic5647 2 жыл бұрын
Great channel. I don't own a boat but I'm in.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LOL.... I'm down like 4 flat tires lol
@Chalz108
@Chalz108 2 жыл бұрын
I'll have you know I'm a master chiropractor who went to Harvard and you built this boat completely wrong. Love your videos man I hope one day I can build my jon boat this way. I like how it's simple and not too over the top.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LMAO I spit my coffee reading that mr master chiropractor! Thanks for watching.
@harlowecustommicrogreens
@harlowecustommicrogreens 2 жыл бұрын
@@SendItJonBoats spitters are quitters...
@appsupport1837
@appsupport1837 2 жыл бұрын
Subscribing in Acworth, Ga.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Awesome. thanks for the sub
@maddgoatee9708
@maddgoatee9708 2 жыл бұрын
Thanks for the great turf info. Should of beat the snot out of both pieces to see which was more durable. Ya, your boat looks really clean.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Turf ain't known for torture. It can withstand doily walking and stuff like that, but it would be a short torture test. Carpet if you are one of those boat people that destroys everything.
@maddgoatee9708
@maddgoatee9708 2 жыл бұрын
@@SendItJonBoats Curiosity mostly. Saw a boat at a ramp that had foam. Looked like someone had stepped on a few lures and weights and left permanent dents. I would have hoped it was stronger then that. One small rock stuck to the groove of your boot sole would make a lot of dents. Thanks for getting back to me. Keep bashing those trolls. LOL
@UWPcustombaits
@UWPcustombaits 2 жыл бұрын
just my personal experience with the amazon stuff it worked on my tiny Jon boat BUT it did shrink so where its jointed together there is a fat ugly gap now, but I haven't had any of it peel up, again just my personal experience with the one and only roll I ordered, that being said I wouldn't want to stick the cheap stuff on any decent rig, go with the quality for sure.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
glad you had good luck with it, that sucks it shrunk up on you.
@chewiepac5932
@chewiepac5932 2 жыл бұрын
Hello from Alaska, comment reveiw best one yet "just saying" lmfao 🤣 keep the hater aid full brother
@chewiepac5932
@chewiepac5932 2 жыл бұрын
Btw as a tiny boat owner that dispizes amazonot I love the poor products that don't work reveiws
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks bro! Glad you enjoyed.
@greenpighunter6930
@greenpighunter6930 2 жыл бұрын
Excellent. Thank you. To hell with Scooter, your beard looks real enough.😄
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LMAO... gotta show the haters some love!
@fireantfishing
@fireantfishing 2 жыл бұрын
yeaaaaaaaah buddy
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yee Yee!!!
@brody2927
@brody2927 2 жыл бұрын
Looks amazing!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks bud. Glad you enjoyed it.
@JerrelBaker-vo8xv
@JerrelBaker-vo8xv 11 ай бұрын
All you need now on cat walk is monster rod holders
@cjwbii9495
@cjwbii9495 2 жыл бұрын
Should paint the side walls on the interior black as well
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I already had then tan so I just left it.
@loicconnan6729
@loicconnan6729 2 жыл бұрын
Rock on ! Thanks let's go Brandon
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yee Yee FJB LGB!!!!!
@gregmitchell3197
@gregmitchell3197 2 жыл бұрын
Your awesome dude!!!!!!!!!!!!!!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks Greg. Glad you enjoyed the video.
@jaacksun4674
@jaacksun4674 2 жыл бұрын
Love the boat build! Have you thought about putting an electric winch on it? I think I’ll end up doing that so I can drag it over logs when the waters low in the woodie holes
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I wish I would have done a winch on this boat, but I di not think about it when building it. I will for sure do that on my next one.
@etowahtraditions3277
@etowahtraditions3277 2 жыл бұрын
Acworth!? I live in Canton, let's fish some time brother!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Heck yeah. I am actually in Covington but soon as the weather warms up I will be ready to fish.
@camdentucker6023
@camdentucker6023 Ай бұрын
You ever ran up Clark creek here in acworth up under 92
@SendItJonBoats
@SendItJonBoats 5 күн бұрын
Never been up there. I stay south when I can.
@rickysmith2248
@rickysmith2248 2 жыл бұрын
I wonder if bacon helps scooters scoot lmao
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Bacon always helps
@allstate125
@allstate125 2 жыл бұрын
Any of that stick on stuff will be trash after some years of sun. Then you have to try and get the glue off to re do it. Good luck with that.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks
@SugarRiverOutdoors
@SugarRiverOutdoors 2 жыл бұрын
Looks damn good dude! But man I'm way too hard on my boat I would tear that stuff up! The chainsaw lives in my boat and when we need to cut logjams out we nose up to it and a lot of times there are good-sized chunks of firewood just falling on the front deck.
@Paidlabor
@Paidlabor Жыл бұрын
did you just get a quote for the rolls? I wonder because each site ask for boat model not just stocked rolls.
@SendItJonBoats
@SendItJonBoats Жыл бұрын
I had to call them to get pricing on just the rolls. I switched to Hydroturf and Seadeck on all my new builds now. You can get them at tbnation.net
@jerrytownsend7314
@jerrytownsend7314 2 жыл бұрын
great job enjoy Scooter
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks 👍
@danielstanfill4321
@danielstanfill4321 2 жыл бұрын
FYI, your boat will sit about 1 inch lower in the water for every 333 lbs you place in it, of course, assuming the weight is distributed so that it remains level. Also, you stiffened it with your modifications. Sorry Scooter.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Good to know thanks
@Ryan55
@Ryan55 2 жыл бұрын
Hater corner is hilarious 🤣 Thanks for the tip on the local source for good foam. I’m down in Jackson GA, I’ll be up soon to pick up a sheet🤘🏼 I think ima just do the bow area, where I stand to fish. I have a 1648g3, My deck is sprayed with Raptor Liner. I guess I’ll want to sand it flat first. Whatcha think?
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I would definitely sand it first. but it should stick fine.
@shender944
@shender944 Жыл бұрын
I’m not sure the price difference but if you have an area that will require multiple cuts around hatches ect you might be better off doing a template and letting the manufacturer cut it. When I did my boat with sea deck the process was to make templates then the vendor printed them in cad and sent it back on clear plastic sheets so I could verify and or mark up with a sharpie for any final changes before they cut them out.
@stevenstarbird1305
@stevenstarbird1305 2 жыл бұрын
Legend has it that Send It hasn’t shaved since he was born…..and he still has to glue on a fake beard
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
The beard jealousy never gets old! Love you guys!
@lovetogun3611
@lovetogun3611 2 жыл бұрын
Im scrolling through the tube looking for ideas for my tiny boat upgrade and all I keep seeing is beard comments before opening the comments 🤣
@smoken66nova
@smoken66nova Жыл бұрын
Fuck the scooters love how you rip em a new one. Keep it up love your vids
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Ha HA thanks bud!
@Buck_slayer7ooo
@Buck_slayer7ooo Жыл бұрын
Also what 3 colors of how paint did you use I didn’t know what Beige
@SendItJonBoats
@SendItJonBoats Жыл бұрын
OHw paint, I did a video on it and talked about the colors. It is a custom mix.
@JerrelBaker-vo8xv
@JerrelBaker-vo8xv 11 ай бұрын
We're you planning on butting live well and or bait tank
@castawayfishingco.6442
@castawayfishingco.6442 2 жыл бұрын
Me and my dad work together and install hydro deck by templates on boats, it’s kinda weird to see a video about them on my fyp
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Nice, it is fun stuff once you get the hang of it. I was shocked how sticky it was.
@ronniekotler9265
@ronniekotler9265 2 жыл бұрын
Like your boat build, not so muck your indoor wall art! Go bulldogs😀
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Geaux Tigers.
@TeamTnA44
@TeamTnA44 2 жыл бұрын
Thanks I will not be attempting this . Lol
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LOL. It aint too bad now that you have all the info on how to do it without failing like me!
@rackdawg5606
@rackdawg5606 Жыл бұрын
Does this stuff work on non flat surfaces such as diamond plated aluminum?
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Yes it does.
@WarpLoTFFA
@WarpLoTFFA 2 жыл бұрын
I was looking to get some sheets but I couln't find where its listed in their site. They could also have an "other" option in their choose your boat menu
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yeah their website is not that great. Try tbnation.net they got all the turf you could ever want.
@hudsone4231
@hudsone4231 Жыл бұрын
I have diamond plate on the bottom of jon boat for floor… do you think hydrodek will adhere to it? Thanks
@SendItJonBoats
@SendItJonBoats Жыл бұрын
It will but you will need to put some contact cement down first.
@bayoubengal67
@bayoubengal67 2 жыл бұрын
Give Scooter directions to the closest Sonic! Geaux Tigers!
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
LMAO ! Geaux Tigers!
@knotengajin7359
@knotengajin7359 2 жыл бұрын
How does it handle mud and blood?
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Mud washes right off with a water hose. Havent had any blood in it yet, will do an update when I take it out bow fishing.
@akbuilder7626
@akbuilder7626 2 жыл бұрын
Hydrodeck, according to their website does not sell this stuff in sheets. It's all deck kits for specific boats. I'd like to buy it but they aren't making it very easy.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Call them and they can help you out. Or you can order sheets from tbnation.net
@akbuilder7626
@akbuilder7626 2 жыл бұрын
@@SendItJonBoats Ok thanks.
@rossgaudet5769
@rossgaudet5769 4 ай бұрын
after two years how is it holding up?
@thaddeusstruckman9974
@thaddeusstruckman9974 2 жыл бұрын
Hey. What color is the main color of the boat
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
dark beige
@maooto
@maooto 2 жыл бұрын
Is there a video on how you did the transom on this boat? Ive got a 1648 lowe im about to do the transom
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yes I did 2 videos on it. They are on the channel
@georgebauman8159
@georgebauman8159 2 жыл бұрын
How can I buy a sheet they only are selling kits
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Contact us at TBnation.net or you can buy a whole sheet at our shops in Illinois or Georgia.
@chums101
@chums101 Жыл бұрын
Looks nice! How is the noise level shutting compartments w this material as opposed to carpet?
@SendItJonBoats
@SendItJonBoats Жыл бұрын
Not too bad. I just try not to let them fall and close them on my own so they dont make a ton of noise.
@terryj257
@terryj257 2 жыл бұрын
Nice work. Have you ever thought of modifying a Jon boat for goin' out castin' & blastin'? Pretty much a camo boat with a blind, that you can fish out of, and a gun holder, that keeps it close and ready.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thats what this boat will be for, duck hunting, cat fishing, and bow fishing
@terryj257
@terryj257 2 жыл бұрын
@@SendItJonBoats oh, I didn't see the blind. I just figured, you liked the camo pattern. Not exactly a camo pattern most duck hunters would pick. Maybe Wood Duck hunters. But what do I know. I see pink camo, blaze orange camo, even something called urban camo. If you want some camo that no one has seen before, get some of that vinyl wrap that looks like chrome and the anodized aluminum wrap, brushed stainless wrap, maybe some gun metal black. Well, pick some flashy, polished metal looking, vinyl wrap. And cut out the camo shapes you want. You could call it "Chromouflage". Oh, I got another one for you, glow in the dark camouflage, do I need to say more? Or how's about a camo pattern that's made out of the naked lady shapes, The kind that all the truckers, have on their mud flaps, and random pairs of boobies, of all different shapes and sizes. Ducks seem to stay away from the guys, if they don't have a blind on their boat, here in Minnesota. Dux must git stupidr, duh ferther thems go sowth. Thanks, Scooter.
@steven33068
@steven33068 2 жыл бұрын
Hello, I love your content. My question is about this eva foam install. I see you used some type of angle to hide the transition from the vertical to the horizontal butt. What is that material? Plastic? Painted aluminium? I need to do the exact same thing on my boat and I need to hide that joint. Thank you and keep up the awesome content. I hope your venture with the tiny boat crew is working. I love the videos of all you guys together. My favorite was the Tennessee build. We already booked a stay there.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Vinyl... I talked about it all at the end of the video for like 5 minutes and showed how to do it.
@steven33068
@steven33068 2 жыл бұрын
@@SendItJonBoats omg.. how did i miss that.. i went with aluminum and im not liking it...
@steven33068
@steven33068 2 жыл бұрын
oh wait, thats the cove base you used around the port and starboard sides. I was talking about this. maybe you used the same vinyl. Here: please check it out. drive.google.com/file/d/1GqGRShyRLvdAiOubNf2cMlzeytq2zIk2/view?usp=sharing
@CreoleCatfishing
@CreoleCatfishing 2 жыл бұрын
I’d love to put this stuff on the front and rear decks of my 2072 Jon boat. In your opinion, how well does it defend against heat. During the summer, the decks get so hot that I can’t even wear dock shoes, much less bare footed🥵🥵🥵🥵🥵🥵🥵. I’d love to be able to stand bare-footed on my deck, and also not partially cook any big catfish that come up on deck. Love the content my friend!!! Bon peche, and Geaux Tigers!!!!!!!🤘
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Turf is awesome. Stays cool all day and I walk barefoot on it all the time. Love it. Geaux tigers!
@ipoopinwalmart5968
@ipoopinwalmart5968 2 жыл бұрын
Dam Scooter that vinyl trim hack looks clean af. Is that hydro deck slippery when it's wet? Thinking about it for my boat.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks, no it is actually pretty gripy when wet and it is cool on your feet.
@ipoopinwalmart5968
@ipoopinwalmart5968 2 жыл бұрын
@@SendItJonBoats awesome thanks for reply. I'll be getting some.
@dmatthews2564
@dmatthews2564 2 жыл бұрын
hey great vid fixing up a POS glassport bass scalper and i would of been none the wiser about the the poor quality amazon knock off.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Yeah I was the same way... and hell the reviews made it sound like it was the next best thing since twinkies and slimjims! Then I got it and actually used it and wanted to warn folks not to waste their money.
@chrisroberts3963
@chrisroberts3963 2 жыл бұрын
Didn’t Nate give you all of his “turf secrets” in Tennessee? 🤷‍♂️
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I missed turf day... I was on a boat. I would say I was fishing but I never saw any fish... so I was just riding around on a boat playing with my pole lol.
@chrisroberts3963
@chrisroberts3963 2 жыл бұрын
@@SendItJonBoats there is nothing wrong with playing with your pole 🤷‍♂️😂😜
@Frank-ih9ew
@Frank-ih9ew 4 ай бұрын
I didn't hear how much these sheets cost?
@biglaverstyle
@biglaverstyle 2 жыл бұрын
How easy is this stuff to clean? Me and 3 dogs get out and in the boat several times each trip leaving mud prints all over the deck. Would it hold up to a car/pressure washer, or would it take elbow grease?
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
It is really easy to clean. I use a long handled truck washing brush and Dawn soap to scrub it down then just spray it off with a water hose. They don't recommend a pressure washer, but maybe one of those low pressure electric ones would be okay like the Harbor Freight ones I wash my truck with.
@brucecochrane9952
@brucecochrane9952 2 жыл бұрын
Nice video, do you know if Hydro Deck will ship to Canada?
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I am not sure, give them a call and ask. They are really nice people.
@southernleisureoutdoors
@southernleisureoutdoors 2 жыл бұрын
Where do you get your parts for your predator 670cc? I'm desperately looking for a new muffler and can't locate one. Help in that would be appreciated.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Message Jeff Clines on Facebook, he built mine and I love it. For all other parts I order from performance670.com
@josephcrouch3734
@josephcrouch3734 2 жыл бұрын
How is that turf holding up to the fin on the mud motor? I have done some damage to my flooring while trailering and would hate to spend the money to trash it on the way to the ramp.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I take a scrap of that vinyl and stick it under the fins so it wont jack up my turf.
@codybenz2447
@codybenz2447 2 жыл бұрын
how well does the hydro turf clean up? possibly looking at putting it on the deck of a bow fishing boat but with all of the fish slime and guts makes me wonder how well it'll clean up.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Dawn, water, and a soft brush cleans it up pretty good. When the weather gets better and I take it out bow fishing I will do an update video.
@codybenz2447
@codybenz2447 2 жыл бұрын
@@SendItJonBoats sweet thanks man. I’ll keep an eye out for it.
@seangrey3505
@seangrey3505 2 жыл бұрын
Wouldn't the foam act as floatation. If I sticks that good might keep er floating on a ruff day
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Maybe, I dunno.
@sgft3307
@sgft3307 2 жыл бұрын
Excellent info! But sure were grunting while peeling off the hydro turf? Ya didn’t even lift that piece of aluminum lol.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
Thanks
@grantbruceweed2482
@grantbruceweed2482 2 жыл бұрын
Thanks for the advice Man! Also, Quick question: What kind of welder do you use and what do you think about it?
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
I run a Titanium 200 Unlimited with spool gun for Aluminum. I really like it, but I am about to get back into tig welding.
@jeremyswisher7403
@jeremyswisher7403 2 жыл бұрын
@@SendItJonBoats I’m signing up for a TIG weld class. Close to retirement need stay busy.
@UltraMagaFan
@UltraMagaFan 2 жыл бұрын
Hydro Deck does not have camouflage flooring. They really need to start making camouflage flooring. Thats why I'm sticking with Sea Dek if I ever put foam flooring in my john boat. I plan on using it for duck hunting. If they did id totally be down to try it but they dont.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
yeah they need some camo.
@christophermccrary8080
@christophermccrary8080 2 жыл бұрын
Get the flooring from Prodigy Boats. I've seen 2 duck boats that get used regularly, and their stuff holds up well, especially of you're looking for camo.
@UltraMagaFan
@UltraMagaFan 2 жыл бұрын
@@christophermccrary8080 Thanks but I think I’ll stick with SeaDek if I ever decide to put flooring in my hunting boat. We have it in our fishing boat and It has lasted 14 years. Other than minor fading it’s still like brand new. That’s to be expected. We fish year round so our boat stays outside.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
@@christophermccrary8080 They use seadeck and hydro turf. Good stuff. That is what we now sell on tbnation
@Bobbyl007
@Bobbyl007 2 жыл бұрын
Hey Nimrod, Scooter here. Nice video. I appreciate the effort and information. I'll check them out. How did it work over deck rivets or is that a no go?
@Bobbyl007
@Bobbyl007 2 жыл бұрын
I see at about 8:53 that it looks like you may have left a small piece of backing paper. It could just be a visual artifact on camera, but it looks like it might not have been visible from the angle you were viewing at that moment.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
yup. worked fine over rivets. I sanded the counter sink rivets down flush so you cant even feel them under the turf.
@SendItJonBoats
@SendItJonBoats 2 жыл бұрын
That is very possible... stuff happens, it aint coming back up now too late lol
@johnsykes706
@johnsykes706 4 ай бұрын
The biggest problem with the more premium brands in Australia at least is that routable two tone for diy installation is non existent. It's a solid colour or custom cnc installation or nothing. And I will tell you right now the Seadeck ect. Installers can jam $3k plus for.a 14.5 foot boat fair up their unmentionable regions. So that leaves ebay unfortunately.. I like your channel though, nice work.
Full DIY Guide to EVA FOAM a Boat | Everything You Need to Know
48:24
Anthony Jones
Рет қаралды 229 М.
Jon Boat Electrical Wiring for Beginners and DIY'ers
35:21
Send It Jon Boats
Рет қаралды 390 М.
Ik Heb Aardbeien Gemaakt Van Kip🍓🐔😋
00:41
Cool Tool SHORTS Netherlands
Рет қаралды 9 МЛН
Чёрная ДЫРА 🕳️ | WICSUR #shorts
00:49
Бискас
Рет қаралды 6 МЛН
We built this Jon Boat in 5 days! Epic Bass Boat conversion
22:11
Send It Jon Boats
Рет қаралды 31 М.
LED Light Bars for Boat || Do-it-Yourself Waterproofing CHEAP!
15:40
Send It Jon Boats
Рет қаралды 80 М.
EVA Foam Boat Flooring Complete Application Guide | Jon Boat Build
24:56
I Bought Amazon BUDGET SeaDek For MY BOAT! (Is It Worth It?)
21:13
TightlineTV
Рет қаралды 458 М.
Scooter Missed Me. Did you?
22:07
Send It Jon Boats
Рет қаралды 1,3 М.
DIY Catfishing, Bowfishing, Duck Hunting Jon Boat Conversion
30:29
Send It Jon Boats
Рет қаралды 851 М.
2070 jon boat conversion | The craziest boat I’ve ever ever built!
31:07
DIY Wood Transom that will NEVER ROT OR FLEX
11:14
Send It Jon Boats
Рет қаралды 103 М.