Hyundai Getz 2010 - How to Replace Bumper Rubber of Rear Shock Absorber

Рет қаралды 37,700

4 жыл бұрын

Hyundai Getz 2010 - How to Replace Bumper Rubber of Rear Shock Absorber
For Educational Purposes only
This is just my DIY Project
For professional support, please visit your nearest authorized car maintenance.
Music Credits to:
• Happy - MBB (No Copyri...
• Video

Пікірлер: 31

@jvt3057 3 жыл бұрын

Thank you so much man! I have searched whole KZfaq to see how you remove the side panels in the trunk!

@albertborrero2594 Жыл бұрын

Hi, Christian. Good DIY content. One detail though installing the bumper: insert one indent of the bumper inside the shock dust cover. Doing so the shock piston would be completely covered without the dust cover falling down along the shock tube. The piston rod shoudn't be exposed. Also the bumper would better serve its purpose to buffer metal to metal contact of the shock tube seal and dust cover during maximum compression of the shocks.

@timothynavarro152 3 жыл бұрын

salamat po at meron nito! very helpful

@TheDlh69 10 ай бұрын

Thank you! Excellent video😊

@jk_minion2446 2 жыл бұрын

thank you very much for the video, it helped me✌️

@Isaac21077 Ай бұрын

You didn't need to remove everything, the little compartments on the sides have a little plastic part you pull out and gives access to the shocks.

@sainathkondbhar 3 жыл бұрын

Thnaks

@kaltengngaji4059 2 жыл бұрын

Terimakasih ilmunya

@jerickberdan764 3 жыл бұрын

sir baka pwd ka din mag upload sir ng diy change oil ng getz and flushing ng fluids ☺️ thank you sir

@TheWarriorHyzz 3 жыл бұрын

can ushare the link of the bumber the defuser

@henreeyuma 3 жыл бұрын

Upload kpa po more hyundai getz vids

@christiannavarro7795 3 жыл бұрын

Salamat po. Suggest po kayo ng pwede i-DIY.

@insu3 3 жыл бұрын

Ok, looks like very solid tutorial for DIY! I've started to replace shock absorbers + rubber with help of it, but... I was stopped by "other rubber". How do you detach those seals on side and back doors? (3:35 and 4:08) It is "pull me hard" technique?

@insu3 3 жыл бұрын

Ok, found it. It's "pull me gently, but firmly" technique. ;)

@MagicBox4u 3 жыл бұрын

How to get these rubber for rear shock absorbers?

@di3d3monz 3 жыл бұрын

There's actually a flap you can open and not have to remove the whole panel😁

@di3d3monz 3 жыл бұрын

At around minute 3.30 the side pockets....you can pull the first flap...and then youll see a square cover...remove that and you'll see the cover for absorber

@christiannavarro7795 3 жыл бұрын

@@di3d3monz Thanks for the tip. but that will be useful if i have the proper tools designed for it used by casa. This is just my DIY at home project using limited available tools only.

@RrRr-th1kf 2 жыл бұрын

Christian Navarro what is the benefit of this parts ??? Is it reduce damping and vibration????

@dAndrei279 Жыл бұрын

@@christiannavarro7795 you don't need special tools. A flat screw driver for removing the square cap, a 17mm wrench and something to hold the end of the shock absorber. Doing so the removal of the shock absorber is much faster.

@dAndrei279 Жыл бұрын

@@RrRr-th1kf this part is used to protect the shock absorber from dust and mud

@hammerhead7344 Жыл бұрын

Do you have to buy the whole piece or just the yellow rubber??

@F.e.n.i.x13 3 жыл бұрын

Greetings a help please, I have the packaging of the additional coolant broken and I want to replace it, according to the one I have has the replacement code is 25430-1C000, I would like to know if the container with the replacement code 25431-1C000, falls the same or works same in my hyundai getz 2008? Thanks in advance.

@christiannavarro7795 Жыл бұрын

same