Hyundai Pull Type Clutch Release System Servicing

Рет қаралды 219,814

9 жыл бұрын

Hyundai and Kia pull type clutches have a few unique service procedures. We'll show you the trick to getting the transaxle unlocked from the clutch and how to setup the clutch and bearing for an easier assembly. For instruction bulletins and additional videos by our part number go to www.clutchtechsupport.com

Пікірлер: 38

@richyvaldez6129 Ай бұрын

Very helpful tip. Thanks 👍

@oprashanth 5 жыл бұрын

It's an awesome video, my mechanic struggle to remove the cover said it's jammed. Later when I checked online and removed the leaver it came out easily

@aaronwoods6640 10 ай бұрын

Thank you! this is a very important step!

@thomasyoung2458 6 жыл бұрын

Good help thank you so much

@edward123ize 9 жыл бұрын

At the end of the video when you pushed on it and forced the click, was the transmission already back I place and screwed onto the engine ? Or was it still cracked open and in bolted like in the beginning of the video? Thanks

@shawone1 5 жыл бұрын

What are the symptoms that this part in need of replacing and how many hours does it take to do the whole job please and thank you!

@BillyRillkratz 3 жыл бұрын

Thanks, Good help!

@ashliestockwell2363 7 жыл бұрын

I have a 01 Hyundai Tiburon and we just changed the clutch and we put it back together but then the clutch release isn't catching can you please tell me what to do

@shaquiem 6 жыл бұрын

I have 97 Elantra GLS, 1.8L. 5 speed. The Bell-housing on the Gearbox/Manual Trans. is busted, and i wish to change it...or replace the entire Manual Transmission...do you know where i can get it online to order etc. It is exactly like the MT youre working on. (Thank You)

@lbarragan37 5 жыл бұрын

How would you remove the throw out bearing from the clutch

@arielmedina9948 Жыл бұрын

👍 great, fantastic 👏

@jasmwhite1 8 жыл бұрын

Do you have any complete removal/installation videos of the clutch assembly on this transmission? Great video! Thank you.

@jasmwhite1 8 жыл бұрын

I actually took a closer look at mine today after commenting. And it looks a little different. My car is a 2010 Elantra Blue with a 2.0L 5-speed. I just wanted to make sure it would be the same as your '99? Very well done videos though. I will sub' your channel for sure! Thanks for the help. Merry Christmas!

@germanmayorga4987 Жыл бұрын

Gracias por su ayuda

@Vex-_-345 5 жыл бұрын

I need help my clutch pedal only goes halfway down I took the slave cylinder off in my release arm will not move it will only move if I use Leverage. Can someone give me an opinion on what they think might be wrong is it internally or is it something else?

@VE3UET 2 жыл бұрын

I have a 2015 Accent, and I have to push the clutch pedal all the way to the floor, is there an adjustment so the clutch disengages closer to the top of the pedal. Based on your video, is the clutch wear, causing the stroke length, or is the pedal on the floor mean, I have a newer clutch. I just bought the car and 99% of the people I talked too, don't understand my question

@leilanipagdilao9674 6 ай бұрын

i followed the instructions and did the same as the video but once i push the release lever to hear the click then i cant push the clutch because the slave cylinder piston keeps pushing the releaze lever so far out it makes the throwout bearing pop off again. anyone know what i could have done wrong ?

@Bimmerstyle 3 жыл бұрын

thank you

@LawatheMEid 3 ай бұрын

What is the type of hyundai avante 2008 clutch?

@specialized29er86 6 жыл бұрын

Preventive maintenance is the answer.

@luisvelasquez9191 5 жыл бұрын

*Gracias ,es muy bueno tu vídeo.*

@oprashanth 5 жыл бұрын

Aligning was tough task didn't know the best way.

@syedirfan29071984 6 жыл бұрын

How to put clutche pleat

@IanStephen21 5 жыл бұрын

I see you've recently responded to questions, so hopefully you'll respond to mine. I've replaced the pressure plate, throwout bearing, clutch, master/slave cylinders/lines, and have also pushed the lever arm towards the slave cylinder and havent hear a click until the arm goes away from the cylinder. What exactly would the problem be? its a 2003 hyundai tiburon gt with a 2.7 liter and 6 speed transmission. any help would be appreciated, thanks.

@IanStephen21 5 жыл бұрын

@@perfectionclutch So I've done what you said and it's still not working. It's like the throw out bearing keeps slipping out. It has minimal play and then whenever you push the arm away from the slave cylinder, it pops out and has too much slack in it. I don't understand how it would be slipping out if it has that stupid retainer ring that's nearly impossible to get the bearing out of. Is there possibly a number I could reach you at, because I've been at this for about a month trying to figure out what the problem is.

@vladisimi 3 жыл бұрын

Ian Stephen I have the same problem.. What worked for you? Transmission off and pushing the ring together for better grip on that bearing??

@IanStephen21 3 жыл бұрын

@@vladisimi not gonna lie, lol, I got rid of the car because I had tried everything and still couldn't get it to work

@vladisimi 3 жыл бұрын

Ian Stephen I was also in the mood yesterday to ignite the car 🔥😂 But I tried to separate the transmission yesterday. I adjusted the circle to point down. (I had it at an angle during the first installation). after pushing the lever I heard it click into the TOB. And I think it's in place.

@leilanipagdilao9674 6 ай бұрын

did it every work for you guys ? ik its an old video lol but i am currently having the same issue

@zbrogan1922 7 жыл бұрын

When i did mine i didnt release the lever to take the tranamission off is that bad

@thomasyoung2458 6 жыл бұрын

@712653519 5 жыл бұрын

Dear mr. The rusted piece that had a rubber the (cylinder can) how did you reassemble it? Can you please make a video about reassemble and assemble it?

@oprashanth 5 жыл бұрын

You could have done full removal and installation video.

@bigr0075 4 жыл бұрын

If you need that you probably shouldn't be doing this repair

@edward123ize 9 жыл бұрын

**un bolted

@danielmalloy6093 7 жыл бұрын

Thanks Gary. Your perfection clutch installl was perfect! Job Done.

@danielmalloy6093 7 жыл бұрын

What I wanted to say was, your video was used as procedural support for a mechanic who didn't speak english. The pull-type clutch system and throw out bearing procedure was key to watch for him..Thanks again.