Whats going on yall today I bring you another boat rebuild its a 2001 Moomba V8 Ski Boat. It rough but I'm sure we can get it back on the water!
Пікірлер: 149
@thejourneymen77223 жыл бұрын
75% of flood damaged vehicles could be saved If the insurance companies would take care of the moisture issues right after the incident but instead they send them to auction yards where they sit for months and years on end slowly deteriorating to the point it’s cost prohibited to fix them.
@WhereverHugo3 жыл бұрын
Yeah, you're right. Such a shame...
@DArynBDeMoss Жыл бұрын
Honestly just seems like that’s the plan all along. Makes for great YT content though
@neoleomedia1676 Жыл бұрын
I believe it’s more cost effective, hence the just throwing vehicles away.
@00nutt3 жыл бұрын
Heck yea!!! Love to see a good budget build!!! Shows everyone anything is possible!!!
@Tjcooke183 жыл бұрын
Love seeing these wake boat rebuilds. Keep doin em
@robprice65733 жыл бұрын
Great to have you back!! Glad your working on another boat.
@seenred69693 жыл бұрын
Keep these boat rebuilds going 🤙. It’s definitely motivation to get my boat going. Subbed!!
@luizhairsalon39173 жыл бұрын
LOVE YOUR PROJECTS, Texas is the holly place for boats, wish live there :)
@SlightlyLessFat3 жыл бұрын
DUDE! That Holley carb is 100 times the Edelbrock carb your friend just soaked you for. I have the same engine and carb in my 1990 Supra Sunsport and it runs flawlessly! If you want EFI, look at the Holley Marine Sniper EFI system. Its what I want to run on my boat. Good deal on the Moomba though! Cant wait to see it done! Side note, the V-Drive is best for surf/wake board and direct gives you a flatter wake for slalom skiing. SOBs pop right up out of the water. Your Moomba wont ride like that Mastercraft though. The hulls are SO different! You will have more bow rise in your Moomba vs the MC but will most likely have the better ride in rougher water due to its deeper V hull.
@thirdcargarage2951 Жыл бұрын
Wrong… An Edelbrock is a perfect choice for a non carb guy. Bolt on and run. The 750 Holley is too big for that motor. Boats are generally full throttle or idle. With a Holley you need to tune it, adjust it, spank it, jet it. The Edelbrock will just work out of the box and stay reliable. Especially with an electric choke. On a car I am racing, go Holley. On a boat…….anything but.
@don9270 Жыл бұрын
@@thirdcargarage2951 I could not agree more. I have that same Edelbrock on my 1959 Chris Craft with a 5.0l v8 and that thing has been bulletproof and dirt simple to set up. The Holley's are fine for racing- but getting the jetting right, selecting the right power valves, and so on and so forth is a complete PITA and not worth it in a marine application. And yeah- the electric choke just works which is great.
@evankennette11463 жыл бұрын
I have a 2001 outback, its my first boat, put a lot of work into it and it runs so good.
@MrJeddurso3 жыл бұрын
Awesome! Can’t wait to see the final product. A 2001 Moomba for $5,000. That’s incredible!
@uptownscenery91752 жыл бұрын
425$
@natesimmons82413 жыл бұрын
Glad you found another one! With boat prices through the roof you have a couple gold mines there with both of those things!
@shadowstorm_24963 жыл бұрын
Heck ya another boat rebuild! So stoked to see this boat go from trash to really good! And that price made me laugh 😂. That awesome you got it for that price.
@MazdaMiata-gt8kw3 жыл бұрын
Another boat rebuild! glad to see it :)
@Chase.bachler3 жыл бұрын
Love the boat rebuilds. Glad to see another one!
@coolissimo693 жыл бұрын
Great to watch you back in business.
@maggie17673 жыл бұрын
Glad to see more boat content!
@martinmicheal45953 жыл бұрын
Glad to see you back on the tube bro love the boat builds hope this baby works out
@etsonbarentine12233 жыл бұрын
My summers looking good with more vids from you man.
@aekerr60803 жыл бұрын
Ground wire is for the fuel filler deck plate (metal) to connect to the take and then connect to the common ground on the boat. This is to discharge any static electric charge build up on those metal parts which can be be dangerous when you are refueling. 1 small spark/arc + gas fumes = BOOM! Like seeing you do boat rebuilds, pretty cool stuff. I have done my own too, but mine was opposite of yours, exterior was in great shape, interior was rotten to the core. It was a total gutting of the boat and rebuilding.
@briansmythe32192 жыл бұрын
Thats Some Bonus Footage Bro glad that strap held LOL
@conmanxtreme3 жыл бұрын
Nice find, I love my Moomba!
@Ndepratti3 жыл бұрын
I DID miss you. More content please for I'm loving these videos!
@austincassell47413 жыл бұрын
"Carb" guys who can't tune carbs -Holley's are junk buy an edlebrock 🤣🤣
@MrSamdavidgm3503 жыл бұрын
Was just thinking that lol
@boominS103 жыл бұрын
Edlebrock is good, but that holley is gonna out perform it if he took the time to rebuild it
@waggy4013 жыл бұрын
Nice to see you back!
@aaronzalez55083 жыл бұрын
Hope to see you again at Sunset Marine Tx in Alvin for a windshield. The one you purchased for your previous boat rebuild worked out well.
@ronaldharris65693 жыл бұрын
West marine boat clean and you have an amazing bargain boat
@91Grunta3 жыл бұрын
Yep, I've missed you, great channel
@JoeRocket-sf6qs Жыл бұрын
Rebuilding carbs is not difficult and I enjoy it,it relaxes me.
@FordManiac763 жыл бұрын
Use Lysol toilet bowl cleaner on the stained white haul. Smear that blue crap all over the stains wait 15min and wash. bright white after but be sure to wax because it slightly etches the gel coat.
@gonzaloviglino23053 жыл бұрын
Love this ones bro!! Hell yeah
@jmk25523 жыл бұрын
Keep the boat rebuilds coming, would love to see a destroyed jet ski build
@texasqueso55063 жыл бұрын
Do you happen to have a wiring diagram for your Maristar?? I just bought a 2006 Mastercraft Maristar 200VRS and I need to redo the wiring, and can’t find a diagram to go off of! Any help or direction would be greatly appreciated!! Love the videos!!
@tech885963 жыл бұрын
‘I’m gonna do some sketchy shit, do-da - do da. Hope I get away with it…’ 🤣👍
@adamledford20683 жыл бұрын
You should check with skiers choice I believe they used to have a life time warranty on all there gel coat . Might be worth looking into
@variousthings65822 жыл бұрын
Any updates? Love your boat rebuilds:)
@robertfolk45832 жыл бұрын
Zep Orange clean and a kitchen sponge will clean up those seats like a charm. A bit of water and using the rough side of the sponge will clean the vinyl seats like a charm.
@mennoboon80373 жыл бұрын
I am sure you can sell the boats fast and for a good price this year, there is less of everything, campers, boats, trucks etc👍
@panteleon13 жыл бұрын
i love the watsup watsup intro...
@samscudder69512 жыл бұрын
What are you going to do for the windshield?
@rcpilot8053 жыл бұрын
I have a question… what are your opinions on rebuilding a newer boat? Like 2016 plus?
@jgott17453 жыл бұрын
Boat rebuilds are my absolute favorite!! @rebuilderguy, can’t you do a Holly EFI Sniper kit?
@chriswise71423 жыл бұрын
Can't be run on a marine engine, unfortunately. No spot for the O2 sensor in the marine manifolds.
@bclaverenz1 Жыл бұрын
You Did Good
@Lawdogg12d153 жыл бұрын
What is your windshield gus name? I'm looking for a windshield for a 1991 Ski Supreme. Hard to find parts for older ski boats. Like the boat builds!
@baconforever55503 жыл бұрын
Boats are the best rebuild
@Freydale3 жыл бұрын
Boat rebuilds are my favorite. Do you still have the nautique?
@faresan54863 жыл бұрын
the rack you used to tie the nose of the boat to is there to help prevent a load falling over backwards. You will be a lot better off tying it off to the mast itself if you insist on lifting boats this way.
@davidrogers9266 Жыл бұрын
Green wire on a boat indicates it is part of the bonding system. Bonding is closely related to cathodic protection and simply refers to the electrical interconnection of metallic objects (such as shafts, rudder stocks, struts, etc) that remain in common contact with water to protect against galvanic and stray current corrosion. Bonded metals are connected to an anode, which is a source of cathodic protection. Electrical resistance between an anode and bonded metals receiving protection from a cathodic protection system should be kept to a minimum and not exceed one Ohm.
@brandonsrednicki61733 жыл бұрын
I'll take the holley carb if your going to trash it
@trevorgulino96263 жыл бұрын
Do you sell the boats off after fixing them? If so I’d be interested in getting one
@dmlandscapedesignllcatlant8093 Жыл бұрын
One restore would make it look brand new no painting
@gplusgplus22863 жыл бұрын
Cant believe noone bothered to buy it for the engine alone...
@boominS103 жыл бұрын
Same exact windshield used by Bayliner
@anthoneyking65723 жыл бұрын
Man you Love your Boats but if they make a Profit its all good Pleased you back at it again missed you lol
@mechanictaft48483 жыл бұрын
The fuel pump is on the ENGINE .BUT YOU KNOW EVERYTHING just like I can get parts for that engine for a 1/4 of price what mercruiser charges but you already know that it took me 35 years to learn my tricks unless were friends your on your own I will give you one free tip its $21 for a rebuild kit for that carburetor
@ryan.graham3 жыл бұрын
What auction house do you look at these boats through?
@therebuildingitguy27993 жыл бұрын
Who makes the windshield??!???? I need one for mine
@hotroder0043 жыл бұрын
The fuel pump should be on the engine (right side passenger) front mechanical pump if it has a carb on it ( I know it does )
@zadengauthier52703 жыл бұрын
How come you didn’t want the plexi glass windows? Wouldn’t it reduce weight but still have the same look?
@dudebro22883 жыл бұрын
Is the ground for the stern white navigation light?
@BobWiersema3 жыл бұрын
Your fuel pump is on the engine. Almost positive I can see it at 10:55 on the right side of the engine (left as you look at it). Common carburetor stuff because you only need 6 to 10 lbs of fuel pressure.
@rickcollinsva3 жыл бұрын
They have a edit conversion kit for that little expensive but well worth it more power better throttle response and quick starts just all around better set up. I think it is Holley sniper Eli kit.
@rickcollinsva3 жыл бұрын
Efi dam iPad spell correct lol
@SmokyMountainsHauling3 жыл бұрын
shoulda just got a holley sniper efi. can get a used one for like $500-600
@fromlv12242 жыл бұрын
✌️😉 Good price! 👍
@luke.dantini1913 жыл бұрын
Have you still got the nautique?
@Pontiac65Cat7 ай бұрын
Unfortunately carbureted? That’s a plus. Less shit to go wrong. If that thing was fuel injected and neglected like that you’d have all kinds of issues. Carbs are easy to fix.
@maccrazy23 жыл бұрын
Works toilet bowl cleaner from Walmart will clean the discoloration/stains from the hull. Spray it on wait 2 minutes and hose it off.
@freeridew9003 жыл бұрын
That wire has to go to fuel cap assembly
@ryansouza25793 жыл бұрын
I second this comment. Green ground wire to fuel cap assembly.
@coreybarrett84113 жыл бұрын
What part of Texas? I would love to come help and be part of these boat rebuilds
@ronin61dk2 жыл бұрын
Any update on this build. You gonna sell it ? Maybe interested
@jmudd54493 жыл бұрын
For around 650.00 you could put fuel injection on it.
@jakepowell84283 жыл бұрын
Not true at all bro
@jmudd54493 жыл бұрын
Fiteck fuel injection.
@jakepowell84283 жыл бұрын
What about the o2 sensors bro I have 5 boats I’ve looked into in it about 1000 to 1200 for everything you need
@jakepowell84283 жыл бұрын
@@jmudd5449 lol it’s like 1000 and it doesn’t have the risers
@BrandonLayMusic2 жыл бұрын
Come on y’all carbs ain’t that bad are they? Not like you drive your boy to work. I’m old school to a fault but I’d take a Holley 750 anyway over some Mickey Mouse throttle body kit
@Random-rt5ec2 жыл бұрын
Budget builds are the boats whose hulls develop unexpected leaks as the bottom gelcoat/fiberglass breaks off 2 miles off shore.
@MrSpiller12 жыл бұрын
Is there a part 2 yet?
@jordanheeney23772 жыл бұрын
16:50 is the most terrifying thing i've ever seen
@randyscott33862 жыл бұрын
Ski boat in a boat dock on a lift durring a major snow and ice storm makes for a bad mix . Somewhere there was a lake loaded with ski boats on lifts in docks durring a snow and major ice storm . The used maket is loaded , or was with all the boats .
@ronaldharris65693 жыл бұрын
Good bye carb time for a Holley sniper and an MSD ignition better than factory after that
@kennethperry67538 ай бұрын
What happened? what color is it? Is it running and on the water yet? how much did everything cost... DON'T LEAVE US HANGIN' BRO!
@paulcollins9197 Жыл бұрын
It has a holly carb that's good
@DesertSurfer3 жыл бұрын
Save the money skip the tower thats a ski boat and folks will pay for the pureity of a direct drive ski boat. Roll the Maristar for surfing and wakeboarding.
@genemounce83023 жыл бұрын
I was given a 1990 Brendella ski boat shell last Sunday. ya want it?
@nickmulvey58183 жыл бұрын
It would be really cool to see you put a modern fuel injected v8 in for a budget and show how it’s done
@Pontiac65Cat7 ай бұрын
Fuck that. Keep the carburetor. Simple. Easy. Can fix it out on the water if something happens. I’ve towed in countless boats that were fuel injected that had issues, with my 1963 Glen l with a 283 and a 4bbl Carter carb. Mines never given me in issue in over 20 years.
@TheHarris19993 жыл бұрын
How much would you sell the mastercraft for?
@user-ir5jo9fp5l3 жыл бұрын
I wait and looking forword to see you a next Clip?
@alexmalmstrom72993 жыл бұрын
Moomba in Australian Aboriginal language means “ celebrating together” Here in Melbourne, we celebrate Moomba on the 2nd Monday of March. It’s also labour day! Just incase you didn’t know what Moomba meant.✨✨👍👍👍🇦🇺🇦🇺
@themikehoncho2 жыл бұрын
What a bummer 10 months without an update
@ddoutdoors882 жыл бұрын
Is the mastercraft for sale!!?
@ameyers673 жыл бұрын
No doubt there is broken glass and crap under that cap keeping it from going back down.
@ColinPrince3 жыл бұрын
Really enjoyed the video. It seems strange to me that a boat would sink! Looking forward to it’s rebirth!
@SeaDooEric3 жыл бұрын
Put a Holley EFI kit on it
@kenwest26993 жыл бұрын
Do they make them for boats would love to know?
@don9270 Жыл бұрын
Where are you going to put the O2 sensors?
@Tomas-jx5xs9 ай бұрын
Are you from Texas?
@user-ih1mo8vv7o15 күн бұрын
❤❤❤❤❤
@Bcool6102 жыл бұрын
Where do you go to look for these auctions I am very much so intersted
@swissroll713 жыл бұрын
What’s up What’s up!!!
@nasa_dog30363 жыл бұрын
What is the song you use in the intro?
@CorkRebel783 жыл бұрын
About time!!!!! 🤣🤣🤣🤣👍🏼👍🏼👍🏼👍🏼👍🏼
@robertoferreira_bethopesca1272 жыл бұрын
Gostaria de poder comprar uma dessa e poder trazer pra Maceió AL BRASIL 👍
@turtleking_07643 жыл бұрын
when is the next update?
@vincevanderbijl22033 жыл бұрын
that green wire attached to all the metal parts should be grounding out to a sacrificial anode to prevent corrosion of all those metal parts