We really appreciate your word sir, Have a great days

Itu pakai mesin apa sih boss

Theo mình nghĩ nếu chia ra 4 ống xả ra sau vừa giảm âm thanh , vừa đạt tính thẩm mỹ . Cảm ơn bạn đã cho mọi người một trải nghiệm mới . Chúc mừng năm mới vạn sự tốt lành !

@@Z_Highlights a hiền ơi bộ chân vịt đó a mua ở đâu zay.giá nhiêu tiền.có thể chỉ e đc ko

It needs pulleys to switch the gearing 3x longer so it will go past the porpoising stage and start planing. You can hear it hit the rev limiter instantly. Shes got alot more to give :)

@@eamh2002 It is clearly on a plane. My 18' flatbottom race boat will do the same without a cavitation plate. Mine is adjustable I can pedal it and put the nose just about under water so when I hit the throttle it levels out and shoots out of the hole and then I can start pulling it up until just before it cavitates on the top end for a fast smooth run! That motor has a 6 speed trans in it unless they are running off the crank and removed the trans in it. I agree they need to set up a shifter on it, probably an electric paddle shifter on the wheel would work best if the trans is still in it but they could also setup a manual shifter too. But, to stop the cavitation they need a plate off the back of the boat, and if it was adjustable even better. If there is no trans then they need more prop because you are right it hits the rev limiter too easily, a bigger propr would bite more water and move the boats quicker without hitting the limiter so easily. Just too small of a prop for the hp and ratio the prop is turning. Thanks for your input too!

But that small boat loaded with a massive machine...but still it'd be nice if we have that some here in Philippines.

Really you need a z1000 engine for fishing

Lakas sa gas yan

Heyy, we are VietNamese bro

việt nam

Vuvghgfuuh5tntgjttkmgcmn x mkv jhcfcvhhjkhvhhihjjhchjgghh iijn ohjvbbnnjnhgyjhyjhghvh

Minh lam mot chiec nhu vay chi phi khoang bao nhieu vay e.a dinh dat mot chiec

Do you what material they are using look like thick cardboard

@@josemorua4578 this is fomex 5mm ^ ^

@@nghiavanhieu8692 thanks

I heard that in the US you also have something that is easy to find, why is that? 🥴

I have no problem finding old bikes in the U.S. a dime a dozen

@@Z_Highlights Keep up the great modifications water toys work & we like to watch them . Always has a KZfaq letter on them & thanks again 👏🥰👍

Yes, that is scary.

@@TrevorDennis100 y no solo eso creo que la bencina podría ablandar el tubo de pvc mas el calor generado seria una explosión segura. yo iría por un estanque de metal y alejado de múltiple.

Yes talking balls out man. Why not you drive like me. Go for it. 👍👍😁

Then it would want to fly sky high then.

And you forget how to control 😏😏

And then it makes more widow .....

😂😂

Very wrong comparison..more legs slower, less leg faster. Otherwise centipede would be fastest. Even those with 2 legs and wings would chose to use wing if want to go faster..

I thought the same but then realised he’s not using a welding helmet

And some hearing protection. 😆

444

Easy. Just add more weight to the front. But that will be a problem if the boat is not structurally build to make it light.

Dư lực quá bồ ơi ,

Người ta đang chỉ ổng khắc phục tình trạng nhảy cóc bằng cách dời ghế ngồi lên 1 bàn chân bạn ơi.

@@ZenerNguyen 1 Foot mean 30cm not a real foot 🦶 😂

@@Serpent-qj3nx ok bro.

@@ZenerNguyen 12 inches . Not 1 bàn chân 🦶

Great work love you channel.

Gê z bạn,nc thiệt chớ VN thấy có mỗi kênh le dan j là chế tạo thấy đc,còn máy cái thuyền qua kênh thái lan coi đi rồi nc

dug la ech ngoi daj gjeg.

ชชชช

That would stop the porpoiseing

.

@Jeffery Holcombe and @Sherer Built thanks that's specifically what I asked about in my question on the main thread? This can be corrected with adjustment to the inlet side but the drag could be overcome with hull modification? Such as wedging or angle of transom? Increase bow height to compensate? (reduce the tendency to completely submarine at the first sign of chop lol)