*I turn microwave transformer into a welding machine new technology* kzfaq.info/get/bejne/i5OllcKZtbzTYZ8.htmlsi=n9_ncSCngAyl2QEB
@trolly42333 жыл бұрын
Coming from Texas, Nice work! You should make a Stirling Engine to make the generator spin.
@rayamundson83943 жыл бұрын
I recommend 500 turns on each side of Transformer with thicker magnet wire to give you more amps. Fill both sides of transformer fully with wire. Use n52 neodymium magnets and shave the epoxy down more to a 1/16 of an inch. Use 4 of these microwave transformers. You can also go to a car parts store and purchase a mechman alternator then hook up a solar panel to power the alternator , then spin the shaft with a motor and you get a nice source of power.
@afmr49223 жыл бұрын
in fact, magnets are far from iron. he left a lot of epoxy between the magnet and the iron core.
@shashi50063 жыл бұрын
Air gap is more and morever he welded all stampings for compling. Most of the magnetic fiels will pass through ms plate
@jamal97463 жыл бұрын
So u mean to tell me this actually works?
@r81646393 жыл бұрын
Is he using gas to power it or does the initial crank just provide the momentum to start?
@Henry-go2llАй бұрын
Way cool
@michaelme40282 жыл бұрын
Nice work! But the steel plates used after the aluminium fail for holding the rotor can act as a magnetic short circuit that heats up the metal and lets you loose some of the energy. I also would try to use 3 or 6 coils to get 3 phase AC.
@qasimlove22262 жыл бұрын
Mr. Michael may you explain me some? Small Generator is no taking fuel which is this coil? If smaller generator taking same fuel like these small using things than what the benefit? Please must reply.
@qasimlove22262 жыл бұрын
@Jacques Decelles Alright its mean its not suitable for ac high voltage equipments for regular volts.
@foyjamez2 жыл бұрын
@@qasimlove2226 It could be run from a bicycle or windmill or waterwheel.
@DEVKUMAR-oh2yg2 жыл бұрын
can you please tell me your fb? i need some advice too.
@astikapanca5102 жыл бұрын
.good
@perceive81592 жыл бұрын
His wife will be so happy 😊 she's got all she needs!! 💓😂
@bazofiascbr3 жыл бұрын
Great job mate! Frequency and tension are likely to get off the 50hz, since there doesn't seem to be any sort of regulation. However, all the machines you connected can work fine on a wide range. This is a good generator made from a small petrol engine and a microwave transformer. It's hard to tell how much power it can provide, but then I don't think it is a good idea to push it too far without any sort of regulation. Microwave transformers usually work at 1200w, so I wouldn't feel comfortable going over that power. Then there's frequency regulation (it defines the water pump motor 'no-load' speed) and tension regulation - too much tension and that electric cooker is likely to burn some control component. There's some information on this on the internet, let me know if you need any help to move on to working on that sort of V1.1 improvement.
@ronalddaub79652 жыл бұрын
The hertzer cycles will depend on the RPM which won't be much to get either from the windings on that thing he was only doing 10 RPM to make those bulbs flash about I would say 30 RPM on this thing would be making 240 volt something like that I don't know but I can tell by looking approximately
@LEONARDOLOPESinfordelta2 жыл бұрын
@@ronalddaub7965 Hello, it also depends on the number of poles. In this case it has 4 poles and therefore for a frequency of 60 Hz you will need 1800 rpm to obtain 220V.
@user-mw8xl6yv1y2 жыл бұрын
😂😂😂😂максимум 3_4 А 10_15 V
@kadampavan3 жыл бұрын
Very good! Show us some Voltage, Ampere, RPM, Hertz etc.
@bobbybiggs43483 жыл бұрын
Yea I'd like some proof that the belt used here is actually capable of transmitting 650w or so like your demonstration. I find it hard to believe. Also the core isn't even closed and there's a huge gap between the magnets and the pole piece. It just seems so far fetched.
@kasparroosalu3 жыл бұрын
@@bobbybiggs4348 Yep. No change in engine rpm when plugging in loads and the belt is flapping on both sides as if the "generator" was freewheeling.
@TehMG3 жыл бұрын
@@bobbybiggs4348 Yup, lucky if that arrangement manages to generate more than a couple of watts. Notice how the ground looks like it has been dug up all around the area where he's "testing" the generator? I'll bet anything there's an extension cord buried in the ground to hide it from the camera. The demonstrations in the video are about as fake as fake gets. Even the first test with the incandescent bulbs... you would never get incandescent bulbs to glow even a little bit by hand-spinning the generator shaft like that with little effort!
@user-bk1ft2be9u3 жыл бұрын
@@TehMG "Even the first test with the incandescent bulbs... you would never get incandescent bulbs to glow even a little bit by hand-spinning the generator shaft like that with little effort! " Как раз в данном случае можно заставить, надо соединить последовательно обе обмотки тогда напряжение увеличится в двое, а лампочки загораются при напряжении где-то 50-60в, и ток им нужен небольшой.-Just in this case, you can force it, you need to connect both windings in series, then the voltage will double, and the bulbs light up at a voltage of somewhere around 50-60V, and they need a small current.
@waraxe093 жыл бұрын
Ok I find this all questionable so hear what... I'm looking to create some free current and I happen to be collecting microwave transformers. So I'll test this theory myself... if it doesn't work following all the methods displayed then I'll call out this video. And if it does then I'll upload it...
@markjob6354 Жыл бұрын
*What would really be better is to attach a 3 to 1 ratio Waterwheel to your homemade power generator 👍instead of depending on a gasoline run drive source. Also, how about a rectified circuit to help stabilize the current at 115 Volts AC @ 20 Amps Max ? This would help compensate for any variations in revolutions of your rotor to a certain extent and smooth out your AC cycles to 50 or 60 Hz.*
@normanstephens5815 Жыл бұрын
Are you into all this ?
@markjob6354 Жыл бұрын
@@normanstephens5815 Yes. Why ?
@normanstephens2267 Жыл бұрын
@@markjob6354 im making one now
@a280319776 ай бұрын
يمكن إضافة مكثف 220 فولط 17 مايكروفرداد للتخلص من تذبذب التيار وتحسين الموجة الجيبية
@markjob63546 ай бұрын
@@a28031977 Sorry, Can't read Arabic
@Gravity42202 жыл бұрын
Look at this mortal with his impressive primitive works
@mehmetcagatay60192 жыл бұрын
This is a very good idea, but a better renovation could have been done. For example, by pushing the second 220 volt winding further back, a cavity would be opened in the microwave oven core suitable for the outer diameter of the rotor, because there is a very suitable space for this process in the two cores. A round hole suitable for this rotor would be opened on a milling machine so that a better magnetic coupling would be provided and this magnet rotor would be able to induce more effective induction currents in 220 windings and generate electricity. If it were integrated later, for example, even at lower revs, there would probably be relatively less fluctuation or flickering. These are my own personal opinions of course, But the 220 volt AC winding connected in series only provided an efficiency like 220 volt AC, because of the magnetic fluxes of this leakage core magnet output. If these leakages were further minimized, it is highly probable that the electricity generation efficiency would be much better, like the rotating squirrel cages of shadow-pole induction motors. Still, it's a good attempt and a good (quite successful for electricity generation purpose) renovation, well done. Good luck with.
@MakarovFox Жыл бұрын
no isnt a good idea this is so fake
@skanderchida9174 Жыл бұрын
Excellent idea for coupling 2 coils on the same iron core.
@skanderchida9174 Жыл бұрын
Excellent idea for coupling 2 coils on the same iron core.
@piercer48822 жыл бұрын
I thought it was sketchy when he was using a pair of scissors as if they were electrically isolated, but when I seen the bare foot hold down the transformer, I knew It was only going to get better 😅
@savneetsinghrairai68232 жыл бұрын
It's less volts but high amps so he didn't got electrocuted
@Ghst-tl9ec2 жыл бұрын
@@savneetsinghrairai6823 The amperage is what kills you...
@carlbittner96912 жыл бұрын
@@Ghst-tl9ec Nope, you need both high voltage (above 48 V) and significant amps. One can hold on to a power source capable of delivering 10 volts at 100 amps without any problems, but I sure wouldn't want to grab a source capable of 100 volts at 10 amps. Both have the same power capacity at 1000 watts.
@Ghst-tl9ec2 жыл бұрын
@@carlbittner9691 Lets do a test, I'll hook you up to 30v DC at 100 AMPS for 10 seconds as you stand in a puddle of water.
@colinmartineau44362 жыл бұрын
Those are some big microwaves you had, most transformers are around 5kv from microwaves. Neon signs have 10kv+ ones.
@valdemarvarona31302 жыл бұрын
That’s most be the worlds fastest rice cooker.
@carlschmiedeke1512 жыл бұрын
😂😂😂😂😂😂😂
@rayparr13 жыл бұрын
You can add a large capacitor parallel to the circuit to avoid clipping. Great job!
@canaldaregi50182 жыл бұрын
Perfeito! 😍
@muhindilawrence85872 жыл бұрын
What if you use regulator like power ups to regulate output
@billyjones90452 жыл бұрын
what does a compasator do?
@armuse11 ай бұрын
@@billyjones9045 кандинсатор делает ток постояным то есть когда горелы лампочки они во время врашения генератора мигали конденсатор убирает это мигание. Накапливая внутри себя ток делает ее стабилным
@masboyrc3 жыл бұрын
Wow.. your homemade generator looks so powerful, really awesome 👍
@MasterFeiFongWong2 жыл бұрын
This may be off topic, but someone might find it interesting.Over unity electric generator. By AMA. Segment 1: 1 motor with bar connected to it standing vertically. Circular disc connected to bar that has magnets embedded in it surrounded in high permeability material to focus magnets outward pushing force in an upwards direction from top of disc. Segment 2: Hollowed out cylindrical Bar of material horizontally positioned. Flat hollowed out ring shaped material with openings around its outer top flat edge. Magnets surrounded in high permeability material embedded in these openings. Magnets positioned in openings around ring are in at least 1 of 2 configurations either all N magnetic field pushing out or N,S,N,S all around it. Just depends on whether your going for Piston structure or spinning structure explained below & whether you want it to be DC or AC current. Place these all along the cylindrical bar connected to it solidly, except at far ends of bar. At both ends of bar place ring of material that can be magnetically repelled in specific locations. (magnetically repelled in specific location is in reference to outside of ring area that faces away from center of bar)(Other side of same ring facing in towards center of bar is capable of being magnetically repelled all around) Ring must be connected solidly to bar. points of repulsion on these rings is off set from each other on each end of bar. 3 Hollow ring structures with small square bars protruding from each. Ring structure has all magnetic repulsion on inside of ring shape & can rap around the main bar so that the bar wont be causing friction on things as it moves back and forth or spins. 1st positioned around far left of bar, 2nd position at center of bar (be sure to leave enough room for magnetic structures to be able to move back and forth without hitting it) & 3rd positioned on far right of bar. Tube structure is constructed in two parts that fit together on top of each other length wise over main structure. Tube structure has 3 square openings for the bars that the Ring structures that are connected around the main bar keeping it from causing friction on structure, to slide into. This tube structure is designed with material that does not block magnetic fields. Perhaps some type of transparent material glass or other. At both ends of the tube structure there is a built in circular groove that will house a round disc. The ceiling/floor/left side/& right side of groove has openings for small magnets to be embedded in it, so that the pushing force from magnets is pushing in towards the edge of disc that goes in this spot. There is also 4 openings located on the top, bottom, left & right positions of the open groove. Small magnets are placed in these spots so when round disc is in position these magnetic fields will hit sideways keeping it from generating friction against structure. Far Ends of bar has Cap structure that screws over tube halves holding them together. Cap structure also has 4 points on inside top, bottom, left & right that have openings. These openings have small embedded magnets in them that exert there pushing force outwards (sideways) so it will keep disc in position, generating no friction against structure. Cap is made of material like tube so it does not block magnetic fields. (Note: These magnets in groove and cap structure are only needed for piston design. If Disc is directly connected to main bar so as it spins the bar spins, magnets are not needed here). The disc has ring around it (ring of material goes around outer edge and folds over front side & backside a small distance) that is repelled by magnetic fields so the 12 small magnets will keep it lined up but it will be able to spin without causing friction on structure. The disc has openings on it's flat side that face inside of tube and magnets surrounded in high permeability material are embedded in this disc. The disc has small bar that is connected to it's center that goes all the way to the other end of bar structure through the center of the hollowed out bar and connects to disc on other end. Disc on other end is set up the same but magnets embedded in it are off set in comparison. As first disc spins the magnetic fields will push against specific spot on disc connected directly to bar, pushing bar in other direction, once bar is fully pushed over, further spinning of disc will then align the other sides magnet to push it back. Tube structure also has half moon shaped protrusion on inside and on both halves so when tube is connected they line up to make a full ring shape on inside of tube, these half moon shaped protrusions have at least 1 small round opening on it's side in middle of curve that faces away from center of bar. The opening has a small magnet embedded in it so magnetic force is repelling out sideways away from center of bar. The protruding ring is positioned to line up slightly further in towards center of bar then the ring of magnetically repelled material connected directly to bar. This way when bar moves right or left it is magnetically stopped after a short distance. Copper coil setup: Copper coils are wound in at least 1 of 2 ways. Either coiled in circles next to each other (Like if you wound coils around a cylindrical bar) or laid out in a row as if wire was on flat table going up then bent to go down & back up until it formed a flat rectangle of wire bending up and down and then the entire structure folded around tube. Copper windings are then lined up perpendicular to magnetic fields on outside of tube. Ends of copper coils are connected into separate construct that will allow electrical current to flow somewhere else. Circular construct is built like a stand that goes around the outside of motor segment. Circular construct has flat ring of high permeability (magnetic field shielding) material that has small openings that will allow magnetic fields through specific locations. Top of circular construct has groove to allow the horizontal bar to balance on. Circular construct can also be placed on other end of bar so it is balanced. The motor segment is positioned so the disc connected to the bar that is connected to the motor is lined up so the disc passes under the horizontal bars disc that is at end of horizontal bar. The high permeability material keeps the magnetic fields in disc from hitting into the disc that spins or pushes the horizontal bar until just the right moment when the impact will cause the disc in horizontal bar to spin which will perpetuate the piston motion in the horizontal bar. More horizontal bars of the same design are built and positioned around the motor segment in a circular horizontal fashion all the way around. The bar connected to the motor can be increased in length to desired height (As much as motor can handle) and more of the exact same setup is repeated higher and higher up, maximizing the over unity potential of the construct to ridiculous proportions. :D Current from the horizontal bars is diverted to power the motor as needed and all other current is diverted to power my game console or the world. :) Interesting variation to this design would be to connect the spinning discs on far ends of horizontal bar to main bar that magnets are connected to so the magnets spin instead of getting pistoned back and forth. So long as moving magnetic fields are perpendicular to copper wires it should work. By AMA
@Two_Bears2 жыл бұрын
Sir; by welding the laminated core as you have done, the reduction of eddy currents is bypassed and excessive heat will be the result. How hot is this project getting on the core and does it effect the efficiency very much?
@vlogcity11112 жыл бұрын
It appeared to reduce the cogging when he initially spun the generator by hand? It should have more resistance to flash the bulbs. Maybe shorting it reduces cogging but heats itself up due to eddy currents?
@theknowledgewithin65142 жыл бұрын
14:53 in you can see he has moved the left coil closer to the spinning magnet to increase voltage output. This is totally plausible. I agree this works
@waqaskhan1482 жыл бұрын
Yes it works but probably not producing more than 100watts ☺️
@yunielcortiza9883 жыл бұрын
Good job brother, parece que ese generador tiene poco frenado.
@user-fb3db7vq2w3 жыл бұрын
Брехня 100 пудов, двигатель от косы даже обороты не потерял при подключении нагрузки
@kokot_usaty2 жыл бұрын
there is a big loss of energy because the gap between the coils and magnets is huge
@degundewid57802 жыл бұрын
Show your work, don't just commen
@alananderson0070082 жыл бұрын
This video is fake as hell
@joshhayl74592 жыл бұрын
🔵 Will power from this be okay to run sensitive Electronics like your computer with?
@degundewid57802 жыл бұрын
@@alananderson007008 the hell is real not fake
@kokot_usaty2 жыл бұрын
@@alananderson007008 i wouldnt say its fake it might work but it will not output exactly 220v
@nelute58 ай бұрын
Ai făcut o greșeală enormă, prin care ai pierdut ceva ce te-ar fi făcut să...plutești de bucurie ! N-ai mai fi folosit motorul termic, iar generatorul ar fi mers la infinit !
@Brassmonger3 жыл бұрын
Coils need to be closer to the rotor and the top side should be welded with lamination plates Same as bottom.
@JM-yx1lm3 жыл бұрын
Why? Was it not working?
@Brassmonger3 жыл бұрын
Now some of the magnetic flux is leaking in the air gaps between central core and sides instead passing the copper coil. The bearing housings also need to be made from non-magnetic material, because they now are shorting some of the field to pass trough them instead of the main lamination. I have learned motors and generators design in university and I know how important is the size and position of each element and how the magnetic flux is running trough iron cores and air gaps.
@user-bk1ft2be9u3 жыл бұрын
@@Brassmonger Молодец, что изучал, но плохо наверно учился, я не имея институтского образования сразу увидел что это фейк.
@Thebasicmaker2 жыл бұрын
@@JM-yx1lm to close the magnetic field
@robinfielding95063 жыл бұрын
It was funny when you showed how aluminum couldn't be welded with a welder like mine. If it would have welded it would have surprised the crap out of me. Loved the video
@SamMonkulas3 жыл бұрын
Try welding Aluminium with steel using HHO welding machine or water power welders.
@ageanageanic2803 жыл бұрын
You can weld alumium bu using mig, but you need to use aluminium wire :) , If you want to weld different metals, yes its possible as well :)
@robinfielding95063 жыл бұрын
@@ageanageanic280 you need gas my mig isn't set up for gas But they have rods you can use with a propane torch
@totheleftrightla2 жыл бұрын
Now this is someone who can think straight and show a good natured human thing without the clutter. Nice art and excellent power output. I can see a host of applications and other sources to spin the rotor, great up-cycle.
@machiii73942 жыл бұрын
This is really awesome. You made something you could use from something you likely didn't have a use for at the time. Although it's rugged, it works.
@mishanya19823 жыл бұрын
*пацаны, киньте кто-нибудь этот "шедевр" доктору Дью!*
@stanislav24253 жыл бұрын
Кинул, я тоже об этом подумал
@mishanya19823 жыл бұрын
@@stanislav2425 *главное чтобы доктор на этот бред внимание обратил* 🤣🤣🤣
@alexinfinity28703 жыл бұрын
Мне кажется, он эту хуйню даже досматривать не будет. Я как увидел зазор между магнитами и обмотками, сразу понял: 7 кВт, не меньше)))
@user-pz8zs6yc2e3 жыл бұрын
@@alexinfinity2870 мало взял! 17 кВт! Он ещё сварочный полуавтомат просто забыл подключить, чтоб тот вентилятор сверху приворить, на активное охлаждения гены😂
@mishanya19823 жыл бұрын
@@user-pz8zs6yc2e 🤣🤣🤣
@serdombr4013 жыл бұрын
Молодец, чувак понимает как можно управлять симисторами с помощью магнита и катушек. Кто физику в школе не учил, для того весь мир полон чудес и волшебства. Расходимся, нас нае..ли.
@KurbanGasbanov052 жыл бұрын
А в реале это возможно. ?
@serdombr4012 жыл бұрын
@@KurbanGasbanov05 возможно что? если такой генератор, то нет.
@laidpily74732 жыл бұрын
It's amazing work ... Thank you very much for sharing it with us
@adrianomoraesmo2 жыл бұрын
Deveria medir a amperagem de saída com amperímetro digital, dizer que tem 7000W é uma coisa, prova é outra.
@JoseCarlos-xz3bz2 жыл бұрын
Nunca vai dar isso! É de baixa potência!
@gato-de-schroringer3 жыл бұрын
Ficou bom . Porem , vc poderia ter pego um atalho ! Ao invés de desmontar a bobina de três volts e ter removido o secundário do transformador , poderia ligar o primário em série c secundario de 3 e de 10kv transformando tudo numa só bobina . Além de economizar tempo , vc teria mais saídas de tenção e maior potencial de geração. Outra ! A onda de saída deve ser bem quadrada no vale e bem pontiaguda nos picos pela frequência das lâmpadas. Tipo um riple forte de saída . Vc poderia ter colocado mais imãs em números ímpares, para imitar a frequência da rede doméstica e diminuir o intervalo de ondas formando uma senoide. Isso diminuiria a necessidade de maiores rotações e ruídos assim como desgaste . Não precisava ter desmontado um motor bonito daquele . Pelo jeito é novo . Qualquer induzido velho já seria suficiente , de ventilador ou de micromotores de refrigeração que acha muito em casas de recondicionamento ou no ferro velho . Ou então uma sucessão de arruelas grossas num eixo tu já faria um rotor produtor de senoides se vc colar imãs em múltiplos exatos de três. Gostaria de ver um vídeo de vc transformando um trafo desses num motor. Faça um buraco no nucleo entre as bobinas que vc tera um motor e transformador. Abraços!
@Kaparzo_King Жыл бұрын
se eu não me engano a secundária dá 2mil volts
@user-se5et8qf3g3 жыл бұрын
А я думал что он и алюминий со сталью сварит, но увы не получилось, а жаль. 😅😅😅😅😅🐮🐮
@inventor19783 жыл бұрын
Hi!
@user-ip7vu2po6x3 жыл бұрын
Через cold welding ,это под силу!
@goiiia37743 жыл бұрын
12:36 Ну хоть подшипник к железяке приварил )
@dead_mx2 жыл бұрын
Это были новые всратые технологии
@MrBiggen19892 жыл бұрын
The best thing about it is the feeling you get when you are using this energy knowing that it is a separate Entity that you made as if it’s a Nother part of you that’s creating energy because he will get to do so awesome video man
@MrBiggen19892 жыл бұрын
You willed it to do so “typo”
@user-jc3hl1he6w2 жыл бұрын
오..멋지네요 너무나도 좋은 아이템 잘보앗습니다 땡큐 땡큐 입니다 늘건강하시여 더좋운 발명품 또 많이 많이 보여주세요 감사합니다..
@c21secco3 жыл бұрын
Nice. Maybe more magnets for more steady current flow(flickering lights)? 🤔
@bavanguron18463 жыл бұрын
I think a capacitor can do the work
@uluhitah122 жыл бұрын
Capacitor does the job.
@diagramasdemaquinasgrafica53103 жыл бұрын
Good work. All that remained was to show the voltage generated with a multimeter.
@bondq74242 жыл бұрын
And check frequency of this generator
@danyf31162 жыл бұрын
@@bondq7424 I have a hard time believing that all these 3 items run on an unknown amount of revolutions per minute to even make a count. No way is this thing between 50-60 hz @220. Anyone care to pitch in?
@norisarabio73072 жыл бұрын
@@danyf3116 that's because it's fake 😂😂 all he keeps doing on all other videos it's hide the cable going to the outlet
@maxguod2 жыл бұрын
@@danyf3116 In theory he has made a four pole generator so it would need 1800 rpm to spin . I don't see a problem with the engine/pulley ratio as they are equal , but I'm not really seeing his set-up doing what it's doing , no voltage regulater , etc -
@rolandoperante30892 жыл бұрын
Yes, check the voltage and the current to know the power generated.
@user-tj8oh1tc7u2 жыл бұрын
Эй! Обманщик! Изначально были подозрения, но почему твой генератор при подключении нагрузки не замедляется?) Ведь должно же сразу создаваться сопротивление)) Ну дурачкам видео интересно будет
@Adam-1182 жыл бұрын
Man I've been having issues with generators in Washington, people always spending $2000.00 on generators. I now see how they work. Thanks man, I'm now 100% sure my generators motor was too old, it backfired one day and never started again. If ida known the motor blew I'd have gotten a new one. Instead I got a different generator that's going to suffer the same fate. I need to learn how to work on motors apparently. Awesome. I do have the old one still so maybe I can learn from that one?
@eagleseye4396 Жыл бұрын
Bro, in my opinion, his method is not really that effective when it comes to creating energy. I've watched something that I want to share with you that you will surely like. Now, this one is legit free energy without any gas-fueled so-and-so, just pure free energy. Let me share with you the link. I think it is way way way better . kzfaq.info/get/bejne/jd2pi72X19madX0.html
@mleiva56973 жыл бұрын
imprecionante felicidades 👏👏👏👏👏
@luisfernandorestrepotorres26213 жыл бұрын
Maravilloso felicitaciones
@stevengould32942 жыл бұрын
Add a capacitor to equalize the voltage so the light doesn't flash.
@eduazasmax2 жыл бұрын
excelente ideia, eu acho que se adicionar duas bobinas em fase em cada lado dobra a corente e a potencia se soma ( 4 coil ) ,duas em paralelo em cada núcleo ( caberia) ,isto poderia ser movido a queda d,água ,com uma pequena represa de um rio ,,onde daria energia o dia todo ,para uma geladeira , um tv ,lâmpadas led, e radio ,
@skanderchida9174 Жыл бұрын
You can increase the magnetic field and the number of coils, and have the magnetic field drive the electric field, in a self contained and closed circuit.
@tyagloevgeniy18423 жыл бұрын
Кульная самоделка. Но нужно сердечник закольцевать ,чтоб создать замкнутую магнитную систему , тогда кпд будет выше.
@SirToddTheGod2 жыл бұрын
Good work! If you were to utilize smaller magnets while increasing the amount of magnets around the rotor then you wouldn't experience the rapid oscillations in the current resulting in higher Hz for a smoother output.
@hanslgurtner30822 жыл бұрын
He doesn't know much about generators. I once recreated one of his generators and saw that it couldn't work. He made a mistake so it couldn't work. During the rehearsal, he must have taken the power off the grid and pretended his generator was working. I didn't make the mistake like he did and it worked for me. Not everything that he shows works with him. That's a little cheat.
@aiman-muggaga Жыл бұрын
@@hanslgurtner3082 Show yours too...
@carlospinheirolopes32632 жыл бұрын
Aí sim para que não tem energia vai ajudar você é bom criador de de energia transformador de meus parabéns 👋👋👋👋👋
@wxdr12 жыл бұрын
Who are you?!?!? This is literally the best video I have ever seen. Words can no even describe the awesomeness!!
@teresogarcia25513 жыл бұрын
Le saludo desde México, Buen video mi Amigo
@salamgomashene40463 жыл бұрын
Use 8 motors to give you 55 Hz so that no electricity will play-Or connect a condenser 50 microphones with 300 volts to stabilize its voltage and hertz
@johnzeena2 жыл бұрын
parallel to the supply from coils? or in series?
@salamgomashene40462 жыл бұрын
@@johnzeena With him Folti exit with a lamp
@zamkhirah69632 жыл бұрын
kzfaq.info/get/bejne/sLyolNtq0tXQZ3U.html
@jhonnyvidros90952 жыл бұрын
Nossa muito top o mas impressionante e que tudo que foi feito e com sucatas que ninguém dar valor meus parabéns pela criatividade
@guruji2432 жыл бұрын
Excellent job very impressed. If it turned a 370w pump than you can use same motor to run itself. This would be free energy. Thks for sharing.
@barneylinet66022 жыл бұрын
Suggestions for improving efficiency of this generator. 1) add soft iron to bridge gaps between the two iron cores. 2) Decrease distance between magnets and iron cores.
@ixflqr2 жыл бұрын
Hey friend, I’d like to understand what you’re talking about, but I only see copper and steel.
@barneylinet66022 жыл бұрын
@@ixflqrThe air gaps between the two laminated iron cores represent a loss; if those air gaps are filled with soft iron pieces, or better yet laminated iron pieces, the generator could produce greater current. Likewise the gap between the magnets and the iron cores is also a loss. The closer the magnets come to the iron cores the greater the current the generator can produce. Air gaps in a magnetic path of an iron core increase the reluctance of the core and limit the maximum magnetic flux in the core. The flux is proportional to current produced.
@profitablebusinessinpakistan2 жыл бұрын
Hi dear I need your assistance in this I want to make same, please contact me mtayyab83 at gmailcom
@guruji243 Жыл бұрын
@@barneylinet6602 I've built one with a washing machine motor with less gaps and good magnets but still gave me 5v ac only and this guy lit 220v easily 🤔
@JharylDonnNan3 жыл бұрын
What is it that it comes mostly to asian people to have such clever and elegant ideas? ^^ Thumbs up, subscribed, heading to my workshop...
@clarklindquist81373 жыл бұрын
They don't spend all day watching TV. They spend it experimenting and learning
@JharylDonnNan3 жыл бұрын
@@clarklindquist8137 well.... OK.... Nothing to say anymore. 👍
@shyaztecguy3 жыл бұрын
Necessity is the mother of invention
@zamkhirah69632 жыл бұрын
kzfaq.info/get/bejne/sLyolNtq0tXQZ3U.html
@fixercinco77322 жыл бұрын
Mucho trabajo, mucho empeño. Pero me quedan mis dudas, cuántos voltios es capaz de generar? Y cuántos amperios soporta? Sería bueno realizar ésas mediciones. El calentador ése nomás ya absorbería toda la energía, y creo que ése bobinado tan chico no produciría el voltage y la frecuencia necesaria para hacer funcionar todo éso.
@eladrixvillalba18012 жыл бұрын
Estoy con vos además el tanque de nafta de la máquina no tiene nafta aparentemente, lo digo xq yo tengo una máquina de cortar pasto igual y se nota la nafta cuando está cargado el tanque esel mismo color q ese pero se logra ver Clarito el nivel de nafta y este parece vacío ... Creo q es Fake
@meditationrelaxmusic90352 жыл бұрын
The main moto to make this video is just to increase subscribers and number of likes, and nothing else
@douglascardenascabrera68432 жыл бұрын
No es fake, lo que pasa es que en esos países los electrodomésticos funcionan en 220v y no es necesario regular, esa planta es capaz de mandar hasta 2000 whatts que esas que suficientes para mover esos electrodomésticos
@hernangiraldo32032 жыл бұрын
Excelente labor muy interesante 👍👍👍
@chrisandlane2 жыл бұрын
Helloooo from the backwoods of South Carolina! Love love love this! Small enough to fit in my boat, yet powerful enough to run my lights, stove, and phone charger at our floating cabin in the swamp. Thanks for the guide, it was a pleasure to watch!
@alseamonoy63832 жыл бұрын
It is not usable for electronics device. As like phone charger, LED lamp. This output power is over damping. If you use more than four Yoke and rotor magnet number eight. Then it will produce efficient output power efficient frequency. This will be a smart generator.
@Ghst-tl9ec2 жыл бұрын
Good way to fry your electronics and catch your boat on fire...
@skanderchida9174 Жыл бұрын
No! You have to invert the power first, or you will burn your electronic devices. All he's doing is generating RAW power that needs cleaning.
@roselineokorie7175 Жыл бұрын
@@Ghst-tl9ec talking nonsense
@pakonektv59793 жыл бұрын
you born in a beautiful place. nice job man keep it up
@markmmm17373 жыл бұрын
Just don't plug anything in that isn't a simple appliance.
@PIXIUGOLD2 жыл бұрын
Nice project amigo so much appreciate your doing.. Highly recommended.. Watching here in Ozamiz city of mindanao Philippines..
@xmachine70032 жыл бұрын
My wife is from Surigao
@xmachine70032 жыл бұрын
Do you watch any of the wood gasifier videos? You should. No gas required. Check them out. Worth it.
@weryfany_Zamosc2 жыл бұрын
Żarówki zasilane tym czymś to jeszcze uwierzę. Wentylator ok ale pompa do wody lub grzałka bajki jakich mało. Ale podziwiam fantazję 😎👍
@koikogo2 жыл бұрын
Zazdroszczę ci. Masz gaz. A my musimy ogrzać dom frytkami. Wkrótce będziemy palić słomę.
@NoOroNnoOR3 жыл бұрын
Masha Allah, very good bro 🙏🏻🙏🏻👍🏻👍🏻👍🏻
@DongStone3 жыл бұрын
We look forward to the consulting experience of major channels like you. Thanks very much....
@felixllayquiorosco74911 ай бұрын
Mis felicitaciones tu proyecto energía libre con imanes neodino Muy bueno buenísimo excelente Lo que te falta es elevador de tensión eléctrica y estabilizador de corriente . dos transformador de potencia
@sukasuka39272 жыл бұрын
You have to show how many voltage and ampere when you test it👍👍 it's will be concern with video title. Thanks
@techfun86943 жыл бұрын
Sir how much power/wattage will produce from previous electric generator using fridge compresor I want to realy make that Awasome idea Thanks for that
@kinghomemade3 жыл бұрын
it can generate 3500W RMS
@suleymanbelik98033 жыл бұрын
@@kinghomemade volt ?
@win95beta53 жыл бұрын
@@suleymanbelik9803 no 3500 watt
@mattwilliams42223 жыл бұрын
@@kinghomemade Nope, sorry. No way. Gullible idiots on KZfaq eat this up. So many things wrong. For one, that motor isn't powerful enough to put out 3500 watts. And, that tiny belt drive couldn't possibly transmit the necessary force if it could. And that's just for starters. People will believe anything they see on the internet.
@000000055473 жыл бұрын
@@mattwilliams4222 That motor can output 3.5kw. Thats like 4.6hp. The belt drive is also fine to handle it but of course it won't last long whatsoever. No need to whine about how other people do things when you yourself do nothing. Tell me, where's your video of your handmade generator that's Oh-So-Perfect?
@BOSS-we3sd3 жыл бұрын
I literally love this my man!! GREAT JOB🔥🔥
@jaye19672 жыл бұрын
Wow, you have a lot of appliance parts. Though if it's anything like most places there are probably a lot of them getting thrown out into the garbage. I'm really enjoying all your videos.
@whatscookingresearch2 жыл бұрын
I truly love the people of the Philippines and the land there. I'm coming back to stay.
@user-yf6bi8li9v3 жыл бұрын
Мне больше порадовало когда он в сверлильном станке обробатывал ну херли биение ноль все строго на глаз! Кстати мог бы и просто скотчем замотать магниты тоже бы работало
@user-es7vu1xy6i3 жыл бұрын
Срочно вызовите доктора! Желательно Дью)
@stalker16723 жыл бұрын
Тем временем Доктор Дью: - вы не поверите, но чисто случайно у меня нашлись 2 трансформатора от микроволновки и не нужный мотор). Что же, мы начинаем начинать!))))
@blackdragon3d4533 жыл бұрын
Хаха точно он проверит эту полную #####
@jeka_13423 жыл бұрын
Только подумал о докторе а в коментах уже ктото раньше меня это сделал😂
@MartinHernandez-se8gy3 жыл бұрын
@@stalker1672 . L L Ll am in in Ml lmm my mlm L I' M Kmm I'm l be mml me I'm mmm El m ml Ok
@user-mb3oi6uc3g3 жыл бұрын
Здирастиии..коменты.начинаем начинать.глазаааа.250 из 250.лайк пиписька досвидонио)
@danielking79884 ай бұрын
this is incredible. thank you for sharing. giving me lots of inspiration 🙏
@bukanpasukannasibungkus48662 жыл бұрын
This is the one project that i believe. Good job!
@hecbrili3 жыл бұрын
Porque no hay un multímetro mostrando el voltaje generado?
@luizcarloslau89293 жыл бұрын
buena pregunta............
@ElisFidandro3 жыл бұрын
porque por cómo fue creado, puede generar una corriente intermitente e inexacta .. tal vez alrededor de 200 voltios pico y 25 Hz .. Cualquier dispositivo funcionaría mal
@javiereduardo71582 жыл бұрын
tal cual ni enpedo tira dos 220 y 50 ghs para q funcione bien td tipo electrodomestico .
@adefaruq76873 жыл бұрын
Please make selfrunning,your make generator is very good,nice video 👍👍👍
@DANIELSBLEEDSRED3 жыл бұрын
Me also new subscriber
@michaelphillips20002 жыл бұрын
Wow nice. The only thing I would do differently is figuring out a way that ounce you get it running the water pump shaft runs the generator so that way it free energy and you don’t need to use gasoline engine to run it.
@jeeshanmathew25892 жыл бұрын
Nice work.. ✌ If u add voltmeter.. Amphere.. to know the values..It will be good..
@leviahamefula39943 жыл бұрын
No frequency, voltage measurements, regulation. Could burn out sensitive equipment. But creative all the same
@user-jr6ue7rk9p3 жыл бұрын
Включил скороварку, напор воды не изменился...) Вот это мощь!
@user-mk5se8ec2m3 жыл бұрын
ну он вилку вставил, но мультиварку кнопкой не включил)))
@RustemRLT3 жыл бұрын
А каша то уже варёная была, он просто её подогревал. Я так понимаю... Или вообще не включил, иначе обороты мотора должны были поменяться от нагрузки, по-любому, хитрит однако. Небось со страны AliExpress 😉
@Gary-ut9ds3 жыл бұрын
@@RustemRLT из Вьетнама...
@octaviochongoarreola54152 жыл бұрын
Muy brother. I lik your letters and hoder letters teasher mi pleace.by from American.
@Gary-ut9ds2 жыл бұрын
@@octaviochongoarreola5415 dont say bulllshit
@erkindalkilic7 ай бұрын
"Thank you very much for your valuable contribution, Master. Well done!"
@AzadAmeen7 ай бұрын
The four globes are how many watts. Thank you for the positivity
@W-Mute3 жыл бұрын
Third, strange hand in 3:07 :) Good job!!!
@CheekyBloke0013 жыл бұрын
that's his foot dude
@sawaengchainee91403 жыл бұрын
ความคิดเยี่ยมยอด
@ronalddaub79652 жыл бұрын
There are a lot of windings on a microwave transformer so probably that thing at a RPM of say 20 might put out a 60 HZ alternating current depending but it won't need to turn very fast to do what it needs.
@savneetsinghrairai68232 жыл бұрын
Also microwave transformers at shorted with earth for one phase...just as vehicles with -ve ground
@minutemindmold6295 Жыл бұрын
This information is actually been abundantly available, it's just been locked and hidden behind gatekeepers at academy and three letter agencies. You can easily find demonstration of this yourself if you just look at ancient megalithic sites. Take a multimeter and put it on a rock, then hold it in your fingers, then put it on a leaf everything has a charge. It's just focusing it into a centralized point with either a capacitor or a battery Bank. Transferring it in white area is where the information gets really scarce. That harnessing it or creating it is stupidly easy take a coil and push a magnet through it where it does not touch the coils and then put the multimeter on each end it'll create a significant current.
@jaewok5G3 жыл бұрын
if you had been out for that boat tour, Gilligan would've been home for supper.
@xmachine70032 жыл бұрын
I would have stayed with ginger and Mary Ann,you guys go home😉😉
@gustavorosales76263 жыл бұрын
Bien echo compañero. Aquí estas demostrando que tu experimento funciona muy bien.
@ernestosilvano90922 жыл бұрын
From Africa I really need know more about it please How can I get in touch with you?
@miorieser32108 ай бұрын
Mach`s mit Wasserkraft! 👍👍 PS Das "Antriebsgummi" zeigt nach Einstecken der Lasten keinen Schlupf.
@ellengeorgealmario23022 жыл бұрын
my name george nanood ako ng mga ginagawa mo very interesting hanga ako sau galing mo. p shout pls thank you from toronto
@Afrikanets_3 жыл бұрын
Скажите, я один охуел, когда он начал алюминиевый сплав к железу приваривать? Слава Богу, не получилось🤣 Хотя от приваренных подшипников тоже подгорает😁😁😁
@goiiia37743 жыл бұрын
Просто у него опыта мало. Я наспор приваривал )) Держится конечно так себе, но держится )
@shootingsolution01233 жыл бұрын
Да эти кулибины достали🤯
@user-oe3qb8lo4w3 жыл бұрын
Нет не один но он потом исправил подшипник приаарил к стали 👍
@Afrikanets_3 жыл бұрын
@@user-oe3qb8lo4w я ж о чём и говорю: от приваренных подшипников тоже подгорает 🤣🤣🤣
@ramirocorteztenorio8563 жыл бұрын
@@goiiia3774 11111
@mydailyideas26342 жыл бұрын
Thanks for your great work 👍
@user-ps8fy1te6p5 ай бұрын
Great idea anyone thinks it can't work doesn't understand basic electrical copper wire steel or iron and a rotating magnetic field same principle as in store bought or commercial generator
@alirezahajali93222 жыл бұрын
بسیار اجرای ساده و در عمل بسیار کاربردی وبدون از هرنوع فریب ....عالی وممنون از کلیپ زیبا وآموزشی کاربردیتون. موفق باشید.
@alvaromurillo88493 жыл бұрын
👍👍👍very good, trank you. Costa Rica Centro América.
@failforwardresearch31272 жыл бұрын
Clever how you put that together. I love it. Although I don't think it will do 7000 Watts.
@iditosa79592 жыл бұрын
Bisa buat las listrik 900 wtt?
@denisosmarcabreraleguizamo98702 жыл бұрын
Exelente, si le pones un capacitó potente en la salida capaz de pueda mantener más estabilizada la corriente
@casimironoresfraga24072 жыл бұрын
Y de cuánto tendría que ser el capacitor
@denisosmarcabreraleguizamo98702 жыл бұрын
@@casimironoresfraga2407 uno de 400 voltios a 30 o 35 mf. Utilizado en aire acondicionado
@alvaroalfonsojimenezmena87103 жыл бұрын
Yo creo que esta muy bien demostrado que funciona. Pero hay algo que es muy importante y muy necesario tener en presente La frecuencia, si no se tiene encuenta según altitud, 50/ 60 hz, podría dañar el motor del estractor de agua y ventilador.
@enriqueparefes9887 Жыл бұрын
Estamos de acuerdo y lo primero seri a medir frecuencia y voltaje por qué para mí tendría que oscilar no es constante
@skanderchida9174 Жыл бұрын
You can use an inverter to clean up the dirty power, and get a pure sine wave to protect your electronic devices.
@robertoricardo7653 жыл бұрын
Aproximar mais as bobinas e colocar neodimel em toda superfície do rotor deixando o com os polos aparentes não submersos na resina mas a ideia foi genial
@user-bk1ft2be9u3 жыл бұрын
Проще и качественнее использовать генератор от автомобиля.
@sheikhnuurshariifkuulow72122 жыл бұрын
Teacher I am In Somalia Mogadishu You Are really a great teacher Thank you Verry Much
@donaldgminski86212 жыл бұрын
I find your use of feet revolting, and hilarious.
@SkitPete2 жыл бұрын
All limbs put to use😂😂😂
@irfan13733 жыл бұрын
Good experimmenting. Can you please show the voltages and amperage on the output of the generator. It will greatly validate your creation.
@mikemotorbike42832 жыл бұрын
Silent videos were invented for the purpose of harvesting compliments from people playing the game, in a sort of mutually backhanded self-congratulatory manner, with the unstated purpose of reinforcing everyone's self esteem as an unrecognized genius. Faith is required, and queries for hard facts could only spoil the effect that suspension of disbelief is intended to inculcate. So, "No." you obviously just don't get it.
@t.fconstruction79152 жыл бұрын
Waw
@Teknopottu2 жыл бұрын
@@mikemotorbike4283 You must have a lot of this faith because even if the magnets were not so far away from coils, this generator would not power more than that desk fan. There can be a silent video showing voltages, amperage and hertz. He most likely has all the equipment but not will to show anything more than devices running on power coming from the buried cable. You can see the ground is dug up.
@robertjonessr.41872 жыл бұрын
@@Teknopottu wow always a skeptic, but surely not educated
@DSB.TecnologiaMaker3 жыл бұрын
Show. Sei que a correia é só pra mostrar a eficiência do gerador, más ela talves não aguente um período longo. Más a ideia é muito boa.
@zalgin_64732 жыл бұрын
Congratulations guys watching her in hongkong .from Philippines..
@sniperpetualang77812 жыл бұрын
Super mantap.... kawan. Bisa pkai 3 buah benda sekali gus.. mantap. Moga tambah sukses lgi. Dan sehat sellu kawan..👍👍👍