Let's take a closer look to the all new Parkside Performance PPHKSA 40-Li A1 circular saw. The machine is not yet released to market, but I hope this will happen soon.
Пікірлер: 32
@sddiymakeitworthit7512 Жыл бұрын
That’s looking awesome 👏 👍 40v wow super
@icku Жыл бұрын
Yes, thanks
@ladismenPce Жыл бұрын
thank you for your review. It really does contain all necessary information. Thx and keep it up.
@icku Жыл бұрын
Glad it was helpful!
@jijibijko Жыл бұрын
Can you make a video showing how it fits with the Parkside track?
@ganakilКүн бұрын
can it cut iron at lower speed like green corded miter saw with 2 speeds and his original multimaterial blade? I have the corded green multimaterial miter saw and it cut very well the iron without sparks. The only downside are the small pieces of iron shoted everywhere. Can the 40v do the same? I noticed is ok with aluminium + bosch blade.
@kovaxzolika Жыл бұрын
Are you not working for the Parkside or Grizzly Tools? I see such parkside machines on your channel, what are still not avaible on the market 😅
@Sammie2010Berlin Жыл бұрын
Nice review! Is it possible to use it with 8Ah and 4Ah Battery at the same time?
@facxone7188 ай бұрын
to bad you are not showing if the saw is straight. on mine there is a 2 mm discrepancy and no way of adjusting it. unlike other brands. or i dont know how to adjust it.
@tomasztomasz5204 Жыл бұрын
Hi, how much did you pay for this beauty?
@ghostanddiy Жыл бұрын
fits Makita rails????
@Michavico6 ай бұрын
Mine runs for a second then stops by itself and light starts blinking, and this is also the case with my replacement machine. Wtf is going on? Tried different batteries, fully charged. Even when not cutting through wood it does this
@Brazmann Жыл бұрын
Hey thanks for another good short Test-Video. One Question: Is there no Laserline on it? For example the cheaper 20v Version "PHKSA 20 Li" hast it
@icku Жыл бұрын
Yeah, there is no laserline.
@jagonight79 Жыл бұрын
Good video,thank you...any updates on the chainsaw performance?
@icku Жыл бұрын
Thanks. I have just uploaded a shorts on it. Tomorrow longer video. But basically you don't need it. Its the same as the green 40V chainsaw.
@matusbelusak3025 Жыл бұрын
hello, can you say me how cost this circular saw?
@6toeNL Жыл бұрын
€129
@kremeszdaboi1862 Жыл бұрын
Okayeg looks good to me :+1:
@petrokemikal11 ай бұрын
This saw makes no sense.. They have a performance 20v plunge saw that operates on a single battery, and then they make this which is obviously supposed to be a site rip saw but operates on 2 batterys.. They have done it backwards.. The plunge saw should have been 40v and this 20v.. This is too heavy and cumbersome to be a jobsite saw..
@wm.g.w.917 Жыл бұрын
Wygląda na mocną aku maszynkę i widać że ładnie odprowadza urobek poprzez odciąg ale jak to w parkside zawsze jakieś detale muszą skopać.
@ruffiopl Жыл бұрын
Zgadza się w 100%. Żal im było dodać kawałka rurki plastikowej do wygiętej w bok lub do dołu. Potem silnik i cały środek uwalony przez opiłki.
@wm.g.w.917 Жыл бұрын
@@ruffiopl A z tym to już różnie , jak komu pasuje jedni wolą odgięcie ( wygięcie ) rury odciągowej inni preferują właśnie prostą , jeszcze inni z płynnym obrotem. Tu nie dogodzisz każdy ma swoje preferencje.
@piatas1901 Жыл бұрын
Jaką kwotę trzeba zapłacić za taką pilarke?
@wm.g.w.917 Жыл бұрын
@@piatas1901 Na polskim rynku jeszcze jej nie ma ale patrząc na inne 40v pewnie będzie około 500 zeta.
@handyhistorian Жыл бұрын
@@piatas1901 569 PLN bez akumulatorów
@DJD8RR Жыл бұрын
Une scie pour gaucher…. 🤢
@OriAngelic Жыл бұрын
190mm and max cut 60mm??? no thanks
@icku Жыл бұрын
Even Milwaukee 190mm is only 66mm, so not big of a difference ;)
@OriAngelic Жыл бұрын
@@icku My bosch GKS 190 - has 70 mm and the smaller parkside 20 V PHKSA saw cuts max 48mm - so im covered, and its just a waste of potential in my opinion - don't saying it is a bad product tho ( own lots of parkside stuff)
@matussmatana7235 Жыл бұрын
Old PARKSIDE PERFORMANCE 20 V (2018) - 190mm, has 62mm cut.
@icku Жыл бұрын
@@matussmatana7235 This one is also rated 62, but when cutting was able to cut max 60mm :) So correct should be 60mm.