How to install stop valve on pvc pipes as shown in the video will make the process of replacement or repair later easy and flexible! How do you see the idea of ​​installing the valve on this pvc pipes ? Please leave your thoughts in this comment section! Thanks for watching !

Correct idea but costly. Single Union can be sufficient

Here in the US, if I was concerned about easy valve replacement, I would just use a Sharkbite valve. Otherwise, if replacement was necessary, I would just cut out a section of pipe and use cemented PVC couplers to connect a short stub on either side.

You only need one disconnect coupling, this is because once the coupling is un-threaded, the valve can simple turn to spin off the male connection on the other side.

I am a plumber and still watch this video ❤

nice. The advantage of this method is when it comes to change the ball valve..it makes it easier 👍

I'm Electronic and Electri Service Engineer . But ❓ I Like The Plumbing Work. Some Time I Fittings Water Pumps Plumber Works. Today I Got New Ideas. Once Again Thank You For Sharing..

Very informative video. I learned a lot from this one, and the plumber never said a word. His work did the talking. My hat's off to you sir.

Plumbing just got a whole lot fancier with this valve installation! 💧🎩

That is the way I assembled my 160' deep well pipe, sans valve, but with couplers between each 20' section of pipe. Continuous poly is usually used but pulling the pump was a lot easier with the couplers when you don't have a crane and winch. Your technique (with one coupler as noted below) is a useful approach to replacing or adding a valve.

Very convenient for disassembly

Thank you for showing this and very idea 💡 you r the best

Mantaf tq for infornation👍👍

Buen video.Gracias por compartir.👍🙋🇪🇦

Hoy aprendí contigo 😮

Excellent

You deserve a hug right now

THANK YOU VERY GOOD AND FUN VIDEO!

Thank you very much

Very good cogragulation.

Now u have 2 find where they sell it and name of it. Also 2 much thread tape can easily cross thread it when screwing on.

Excellent 👌

I've been brainstorming how to install a 1 inch ball valve into a gravity fed pvc line from my spring fed water tank where it enters the house upstream from my water filter. No flex in the pipe so your suggestion is perfect! Plus, the valve is serviceable in the future without cutting remaining pvc again and again. Thanks!

Thank you

Mantap...sangat bermanfaat.....

Appreciate💕 both you and your Shares Thank you

Hay lắm ak.nhớ ra nhiều video nữa nhé

2 things u forgot . when u cut the pipe u have to deburr it. And second thing u have to clean it with a PVC Cleaner before u get the glue on. These are two very important things.

very creative and it worked for me

Overkill...no thanks..

I have had on my mind to install a shut off valve in the 3/4" PVC water line coming into my house for sometime now. This video is exactly what I needed to see to get my valve installed. Will get the parts today. Thank you very much for this video.

What a good idea to apply for...Thanks.

spectacular ocean until you're officially captivate me...great

Using conduit for water pipe looks like problem number one.

Thanks for your Idea WE can need that one day

Nice idea, you can easily change the valve once broken.

1. Only PVC valve (both end female socket type) will be just sufficient to replace. 2. At last you installed the valve diametrically opposite to that you saw in starting of video for correct direction of its lever. 3. Anyway, it is a nice video. 🎉

That's doing it the hard way. Also unless the pvc is schedule 80, the pipe is for electrical work and not code approved for plumbing. Maybe things have changed since I retired after 45 years as a plumbing contractor.

great connection

If you are not a plumber...then hire a licensed plumber.

Beautiful Videos 🍧

Simple and useful tips

thanks for the sharing. it's very necessary for me

Super buenas ideas

Same problem happened in my house...I searched for changing the gate valve....thankyou very much

Enjoyed the finger pointing.

Very good nice videos like ❤❤👍

why have 2 unions when you only need 1? better yet: 1) use a sharkbite shut off (the 2 unions will more than pay for it). or with the shutoff (threaded) shown 2) use a single sharkbite straight connect. 3) sharkbite Quick Connect Push to Connect/John Guest Speedfit Union fitting (these are made out of pex). If its its outdoor or irrigation, use an orbit PVC-Lock fitting (push on). All of these will be cheaper and easier than 2 unions and all will allow shut off to be removed if it fails.

Good lesson tanks

Wonderful shot

Молодец,👍

Breathtaking 💖💖

Muito bom.....RJ,vou fazer

Wooow... very very amazing

Good information sir

Very good ❤

Ide cemerlang, salam kreatif

good job bro, keep it up

Excellent method onday a client asked the same question. How to connect ball valve?

Outstanding

Making a simple task complicated.

Good for you

Good tricks for life

Thanks! Makes it easy, practicable & safe as well as caters for future maintenance if need 👍

Good job sir

I will try with these tips

i love you your idea

Magastos sa materyales hahaha...

good tips. very creative

❤ it's just amazing you are sharing your plumbing skills to assist people who never ever done any plumbing work which is really appreciated, sorry 4 some of the negative feedback in the comments section,have a great day

OMG😍,Awww💞 I love this

Just magnificent 🌹🌹

great job

great video bro

Good 👍

Sweet :) , it is Such a pretty video

The purpose of using union in this TUT in next changing of stop valve you won't cut a piece of pipe. Nice idea.

Why is this better?

This is actual installation of valve and in future easy replacement.

cool lovely looking

thank you for sharing😮

Wonderful💮

Such small pipe is flexible. IF you have enough length, you don't need a treaded coupler

Pvc pipe very easy to install safety valve without union specially smaller pipe

They sell the pvc valve with the unions already on them, much cheaper and less chance of leaks since no threads with teflon tape are used. and they are much shorter than what you put together. If for some reason you can't find the unions and need to fix a problem right away, a valve and 4 90's will work. glue the 90's on the valve and see how much you need to cut from the pipe with the other 2 90's on the pipe. Yes it will not be straight inline as before, so it might not work in some cases, but for most, it will.

This guy seems to know what he's doing, so well done. Very educating video. Generally the problem with plumbers is that if you ask 10 of them how to solve plumbing problem X, they'll come back with 11 different solutions and then they'll start arguing with each other that everyone else is an imbecile and a fraud.

ممتاز جدا جدا شكرا لك يا بطل

This is called ROCKET SCIENCE 😂😂😂

Have a good Day😉

Hi how I can install a spring valves on my laundry machine , thanks

😍great🔥🔥 It's engaging!❤️

Super

Nice idea bro.

Can i use this glue for drinking water pipes ?

slip sharkbite fitting, one cut, done

Dude just cut it and glue it plenty of flex on that pipe

Power of one

More joints than bob marley

What's the point of unions if you going to put them that close to adapters

Great