Thank you for your time and efforts to educate. These old tractors are gems and it is fine people like you who will help us keep them running. BRAVO! By the way I appreciated your time on the phone with my questions.

I appreciate your videos! I have one running b414 diesel and one b414 diesel parts tractor with power steering. You have given me the courage to go into the hearts of these beasts. I may even fix both tractors before I'm finished!

Had a blown head gasket on a 374. Never even been inside that part of an engine. Watched your videos and gave it a shot. Marking my top dead center was confusing for me and took a while and after watching your videos again and again to get it. Success. I have watched all these videos now with the rear end axle, transmission, PTO etc. and now going to take the chance on repairing a popping sound in my left rear axle (hoping it is the bearing), while I have the hydraulic off the top will rebuild the speed control which I found a kit for. Then the next is a knocking I have between the engine and the transmission. It seems to be located in the bell housing area and goes away with the clutch depressed. Things I am doing at 62 that I never thought I could do. Yay You Tube University and Professor CR.

Absolutely fantastic video , thank you for explaining the whole process on removing super structures and the causes , and I am getting one of those large snap ring pliers 😊👍

Thanks for B 414 videos. I just got a 1964 with no operator's manual, and your videos are helping me a lot! PTO was touchy. Only had 1 inch of fluid in reservoir😱😱. Fixed!. There is water in tranny so i will be changing that fluid next. 👍👍

good video CR,i would love to bring my ole tractor to somebody like you!have a nice day.

great explanations, great video. Keep going......

Great Vid, another happy farmer driving his repaired tractor away.

good on ya mate!

I love your videos they are so helpful, thanks for doing them, I have 5 B414 tractors 2 diesels, 3 gas, I am trying to disassemble a R92 power steering cylinder , It turned left good but hard turning right, I got the outer cylinder off but having trouble on the inner one, the manual dose not help much, is there a video out there on these or do you have any used ones , thanks for your time,

Good day. GOOD video what would a bearing that was shot,( was that going transmission) cost. Yesterday I watch grease monkey1 take big JD transmission apart very big bearings. Thanks

Hi Thank you for your KZfaq videos on the 414. they have been very usefully as I have IH444. With regard the Differential how do you split it to replace the diff lock shaft. I have removed the retaining bold but cant see how to split unit is there a tool that is required ?

How to test to see if hydraulic pump is working. The lift is not working and the power steering is not working I need help. Do you have a video on how to test hydraulic pump

Great videos, thanks for posting! - How many man hours to do a job like that?

Nice

I love your videos. I have my father's 444 now that he has passed away and his won't stay in high range unless you hold the lever while traveling. Everything else works fine except that, would you have any idea what could be the cause. I can't find any information on it so far.

Hi Dave, another great video! I have a bottom end leak and it’s coming from what’s described in my B414 parts manual as the clutch housing “hand hole cover”. The manual shows a “sealing strip” which is clearly the source of the leak. What is a sealing strip and can I simply use some gasket maker or do I need a gasket of some sort? Thanks in advance!

I've got an Australian B275 Can't select reverse gear. Were do you wrecken i should start looking?

Hello, Do you have a video to show all the International b414 clutch adjustments by chance? My tractor all of a sudden started to slip some.

Need help with the PTO on a 424. PTO will turn without a implement, but not with.

Hi Dave, My B414 reverses ok on level ground with no load but with a trailer hitched up or with a load on the 3 point jib/ crane or when reversing up an incline... it will start to reverse then jump jump jump - attempting to back up but going nowhere. What do you think would cause this? It doesn't like reversing against any strain/ load.

Hi Dave I got a 424 gas 1967 tractor a few months ago that had set for close to 10 years and seems to be the same problem that you had with this 414 , stalls when you let the clutch out. My question is if the transmission is the same and if you think it would be the same. I did not find water when I pulled the drain plug out. Think you for your time.

I just bought one of these and it pops out of first gear. Second, Third, Fourth and Reverse are all fine. Any ideas on where to start? Thanks in advance!

Have a B414 with a stuck clutch I think, can't put it in gear without much grinding, doesn't stop moving with clutch depressed. Any tricks to unstick or is it a split job do you think?

Does anybody know where I can find parts for a 1980 International Harvester, D358 engine, need a transmission valve assembly!

I enjoy your videos but wish they were a little longer.

ANY 414 pwr str parts to swap onto my 275 ? have been searching for a long time. upstate ny

We need help with a hydraulic pump on a b414 international

hi , i have same tractor and my clutch pedal is very hard to push . My left legs is dead after 2 hours of snowblowing !! what cause this ?

Hi soy de México y tengo un B414 67 que aceite le pongo al hidráulico guacias.

rear left tire backwards?

What was the fluid you used in there please?

Where are you located ??

you use the word grease .....???? would you not fill the transmission with oil????