I made mine today and working surprisinly well! I used a laptox box too, had enameled wire I had as surplus and a varicap from a old radio once disabled and saved. Then with some hot glue as aid did the turns. Many tnx for your practical advises and keep on!

Super cool, Tom! I just bought my first shortwave radio (a Tecsun Pl-310) and it is supposed to arrive in the mail tomorrow. I look forward to learning more from you! Much love from Ontario, Canada!

Now that's magic! Very well done and should be crystal clear in your tree house. Just getting started with radio's and struggling to get to grips with antennas, it seems like a dark art, I will be trying your project once I get some supplies. Thanks for sharing, great channel!

Enjoying your videos. Good to see you doing them again.

To all who may be wondering: this antenna is coupled to the radio inductively, which means there is no physical contact between the radio and the antenna. The radio is simply put in close proximity to the antenna, and the antenna is tuned (by means of the capacitor) for peak signal. I cannot tell you exactly how to connect a capacitor to the ends of the looped wire, as capacitors vary. Some experimentation is called for. For the capacitor I used, one end of the wire loop is connected to one of the terminals on the capacitor, and the other end of the loop is attached to the chassis.

Good stuff Tom, keep these great videos coming, many thanks.

My first medium/shortwave was a Greymark kit. Four tube analog. All spaghetti wiring with Variable Air gap Tuner. Lost it in a flood. The kit Came with three plastic bobbins that had to be wound with copper magnet wire. Those plugged into sockets in the chassis. They had grooves molded into the plastic for # of turns and spacing. They need to be wrapped clean and tight. Ends soldered onto the pins. Tubes were about the diameter of a paper towel cardboard tube. You could wrap two sided adhesive tape carefully to replicate the plastic tube. Or chuck up 1-1/4 inch PVC pipe in a drill or lathe and carefully score grooves in the tubing.

lookin forward to watchin you build a capacitor. Love this channel!

Really nice, Tom! Meet to see you again!

This isn't on topic but have you seen the plans for the Carver ultimate AM antenna? It's for radios that have terminal connections. Basically it's four turns of wire on a 12" square form. I used a large coffee can for a form and doubled the #turns to compensate for the six inch coffee container size. I did experiment a bit to find the best #turns for the different size. I use it for my stereo receiver that requires a loop antenna for am. It works remarkably better than the cheap little loop included with the receiver.

Great video!!! Just watched this and the performance of this homebrew is very impressive. I'm building one right now but the only variable capacitor I could find is a dual gang unit from an antique Silvertone radio. How critical is the value and type of tuning capacitor for this project? I don't want to rip the old radio apart if the tuning capacitor won't be appropriate. Thanks!

Nice crafting! Don't forget to take it outside w/a battery radio sometimes..noise level goes down! Here is a great DIY variabale capacitor: 2 big tapered summer-drink tumblers. The inner has a metal foil (like sicky alu-foil insulation tape) on the outside, covered with the packing tape (insulated), the outer cup has the stickyfoil on the inside, tape-covered. You muckle on to overhang from each layer with an alligator clip. Nest the cups, press down a little, and rotate to tune!

This is awesome, I could really use this. I’m having trouble finding the adjustable capacitor, would be great to have those instructions for a diy option. We’re you able to post those instructions too?

It seems like you could make it into a regenerative amplifier pretty easily with a battery and a FET like an MPF102 and a tickler loop.

Wonderful vid! I'm a rank beginner and I loved it. Although I wish I could make a variable capacitor appear out of thin air!

Great Scotts! Radiodog. Great Video. I will give it a try.

Thanks for nice easy project :) can this type antenna good for short wave as well?

would solid copper telephone wire suffice ? I got a spool of the blue/ yellow telco wire handy

Do you have a video that shows where on the tuning capacitor you connect the antenna wires?

I like the Channel Master radio, but I wonder if your loop will cover the extended part of the AM band.

Does the homemade loop antenna have to be hooked up to the tube radio's internal loop antenna on the back of the compressed wood panel or or does it just stand alone. I happen to have that tuner capacitor and a bunch of other parts including 500 tubes I got from the swapmeet. Hopefully I can get better reception. A million thanks "Radiodog."

Hot glue a bottle cap to the shaft of the capacitor so your hand touching it doesn`t interfere with tuning.

This was an awesome video

@Radiodog I know this video is 3 years old, but I just found it. I have an old Technics SA 110 adio receiver. It came with an AM loop antenna, but that was lost. There was no variable capacitor on the antenna, it just plugged into an RCA jack. With your desugn, can I skip the capacitor and put some twists in the lead wires to a 6:24 n RCA plug?

Radiodog, Greetings! ---- Living in eastern KY, AM radio signals are very weak to non-existent to stations only 1-hr away. I followed your directions on the DIY Loop Antenna using 100-ft of doorbell wire and went out and bought a variable tuning capacitor similar to the one you show in your video --- mine was rated as a single 365 pF. Being a neophyte in the amateur radio world, should I attach both ends of the loop ant. to the opposite leads of the capacitor (mine has 4 contact leads)? I'm not getting any results close to what you had in your video. Any advice you can provide would be greatly appreciated. Thanks!

I have a bust but stereo the antennas are cheap. I’m from Chicago and I’m picking up broadcasting from Nashville @ night, but the volume goes up and down. Is their any way without getting outdoor antennas to fix that problem?

Hi, I'm new to radio and I am trying to build my antenna. However, I don't have a capacitor. Will it work with out it?

Very interesting but you did not show how you hooked the wires between the capacitors and the radio. does the radio have two screw terminals on the back? is everything hooked in series?

Tom just making sure I understand, the other end of the loop is attached to the chassis of the capacitor, correct?

For anyone who is often working on electronics you can actually get this wire (magnet wire) from things like small transformers on circuit boards:)

I'm always surprised at how many people claim that a loop antenna such as the Tecsun AN-200 has no effect on reception. It's clear to me that they are not doing it right. The right radio is important, as is positioning of the antenna relative to the radio and dialing in the frequency correctly on the antenna. I've always had excellent results with the AN-200.

If you wrap the wire around the radio it works even better.

how did you connect the capacitor to the radio?

Tnx for the vid.really interesting.

Two questions: does the box have to be one square of 12 inches per side and 4 inches deep and do the wires have to be equally spaced? This is a pretty cool video. Thanks.

Can magnet wire be used for this project? I have over 100 ft of it

Very good! Thank u. 💚💛💙🇧🇷🇧🇷🇧🇷

Would those AM-FM radios from the 80s that are sold in Goodwill and such make for a good capicator for this project???? Ours has a ton of them for a $1

Very cool!

Gracias amigo

Best I can tell you used bare non- jacketed wire? Can you wrap regular light gauge jacketed wire as I do not have bare wire? Thanks for your very good video👍

Excellent

How to connect wire with am radio and please tell me number of capacitor picture and size

Twaskyou sr Blessings this is my hobby for many years to get lot fairs stations radio and tv.

Love It!

Another idea for a video... Make a high Q loop antenna with pegs in a board alternating the windings above or below each peg.

Can anyone tell me why my Anker 15600 mAh USB battery charger/battery pack is shutting down when attempting to power my MLA-30 Active Loop Antenna??? Is there a simple cure to this dilemma? Thanks

Saddly, you placed the Channel Master in front of your antenna/variable capacitor combo, can't see how it's all connected. Is the loop antenna connected to the radio? How did you connect the capacitor, with both leads or just one? Please reply

It's a pity you don't show one of the most important part, as least for a newbie : how to attach the wire the capacitor ? Have a nice day Tom

Same question everyone else is asking. How did you connect the wires to the radio?

How does your home made box antenna compare to the tecsun loop antenna I see on your desk.?

Could you please put a copy of a schematic?

Did you ever make that "next" video about building an antenna from regular materials? You kinda lost me at "capacitor" : )

Super sir

what material is the wire made of?

Ok, you made a box antenna and you connect it to a capacitor (you don't say why ???). You don't show how everything is connected ... how are we supposed to connect everything? Can this be used for a car radio ?

Since Radio Shack closed, you have nowhere to go for electronics stuff, except eBoo or Amazool. You can easily get antennas for ham radio, but there is nothing for shortwave. The capacitor is only available from a specialty vendor and are VERY expensive, unless you can make one yourself.

You don't even need a square box. I've seen them make from round boxes, rectangular ones, wood forms, etc. The only problem with these simple loop antennas is that they are only useful for the AM broadcast band (520 - 1720 kHz) so you need something complicated and expensive for the rest of the shortwave bands.

3:55 Uh huh yer not sa good with your math either are ya. Nevertheless, I'm enjoyin yer videos and learning a LOT!

You need to get the capacitor as surplus as they are very expensive.

👍👍👍

I heard Curtis on 77 WABC

👍

Or something plastic or non metal to pervent interference

Hello sir. I just bought this 365 pf variable capacitor from the link you've provided in this video (mtmscientific.com). I am from Philippines. Im just worried a little bit because i emailed them but till now no response still. Is this a legit online store? I hope it is not a fake store. Because i already paid it through paypal. Im worried a little bit.

Will this work on a regular radio. I’m tired of not being able to listen to the ball game and want a decent channel

1:29 okay buddy ya lost me there. I thought you said there wasn't gone be a lot of math!

You do not show us, how you hooked the wire to the capacitor, and then the capacitor to the radio. You only show the front of the radio. I already know what the front of a radio looks like.

So many words to say so little. Maybe a quick sketch of the circuit? This video could have been much better with a bit of planning.

Why? Would you want to disassemble an old radio? Radios of all types are becoming rare. Maybe FIX the old radio. Buy your new electronic parts from ebay/amazon, Digikey, Mouser. I have accumulated many old electronics. And wasted many hours trying to desolder components. And destroying parts by getting them too hot in removal. Goodwill stores get a huge amount of electronics. Talk to the guys outback in receiving for special things.

waste of time, you did not give enough imfo how did you couple it to the rec. wire or just sitting there,