Inflatable boat (SIB) - smart way to load and unload to a trailer without it going into the water

No video

Inflatable boat (SIB) - smart way to load and unload to a trailer without it going into the water

Рет қаралды 10,407

Күн бұрын

Our design to load and unload our SIB (inflatable boat) on our trailer, - without driving the trailer into the water.
Even with a 40hp (74kg) outboard it's very easy to load it.
Just for inspiration to others 😊
En video der viser hvordan vi sætter vores gummibåd i vandet, samt hvordan vi trækker den op igen.
Essensen i dette er, at vi ikke ønsker at køre traileren ned i saltvandet.
Det kan virke lidt besværligt, men det tager ikke mange minutter at trække båden på land.
Blot en idé og forhåbentlig til inspiration til andre .

Пікірлер: 18

@fatih1922 2 ай бұрын

Very nice. Thanks for the idea :)

@OmeMachining 2 ай бұрын

Your welcome 🙂💪

@ytboombox Жыл бұрын

that is a big boat, and the loading gear design is very smart

@OmeMachining Жыл бұрын

Thanks allot 😊

@alancadieux2984 Жыл бұрын

I'm going to use a regular flat deck trailer, and build a sheet of matting for the boat to sit on, install 2 air lift rolls about halfway down the trailer deck, full width roll at the back. Why? Because I'm going to be carrying a heavy load of gear, and lauch with all that stuff in the boat, the straps under to pull on the transom work for this well, but I can tie the boat to the matt as it comes up, and pull on the matt. The other reason being that I can use the trailer for other things when not using the boat.

@gb4780 Жыл бұрын

If treating SIB like a RIB, may as well get a RIB. Excellent engineering though. Well done.

@OmeMachining Жыл бұрын

Why do you think I treat the sib like a rib? 😊

@CUBICHI1985 2 жыл бұрын

This is very ingenious. Thank you for sharing!! Did you make the trailer yourself? Would love to buy one like it 😁🙏🙏🙏

@OmeMachining 2 жыл бұрын

Thanks allot ☺️🙏 no the trailer is bought. Made for classfiber types with plastic rollers to load/unload on. ☺️ But of course fitted with planks and rollers to fit our sib ☺️

@icefire8888 2 жыл бұрын

Awesome setup. What are those types of hinges called and the locking mechanisms? Also how does it perform with the engine on?

@OmeMachining 2 жыл бұрын

Thanks for the kind words. Which hinges do you mean? ☺️ Most of them are home made. It do perform very well with the 74kg 40hp motor. But the 30L fuel tank need to go up front to ease it, if it's full or close to full. I actually just re-designed the ramps, and now they are made in aluminium, and with fewer wheels. Mainly to weight reduction as the wheels are very heavy and only the two on top needed a double pair, and only 4 single mounted on the inside ☺️

@icefire8888 2 жыл бұрын

@@OmeMachining would love to see a video of the new setup.

@siedracul 2 жыл бұрын

Genius!!! What size is your SIB?

@OmeMachining 2 жыл бұрын

Thanks allot ☺️ it's 5m long and 2m wide. Weight is 180kg and motor is 74kg+30L gasoline ☺️ we also carry a extra 2.5hp mariner for safety, and other safety accessories. So it's on the heavy side ☺️ but still the 40hp get it to plane very fast

@siedracul 2 жыл бұрын

@@OmeMachining awesome. Thank you. That gives me some good helpful direction!

@guyak65 2 жыл бұрын

Where do you put the straps that mount to the transom while in the water??

@OmeMachining 2 жыл бұрын

I put them on right before loading. It's a two piece strap that end in one in the front. The end where they are tied together is then tied to the front, and then each one is being pulled down the side, under the tubes and then to the transom/motor. Hope it makes sense. It's a 30sec task for each side. 😊

@guyak65 2 жыл бұрын

@@OmeMachining thank you !!!