Damn, I'm in the process of installing a thermostat and decided to check out a video prior just because. I never knew about that little vent hole. I've played with it with my finger but never knew it should be facing up.
@elchanojose8 ай бұрын
Hello Scott! That component helps to get the air pockets out of the engine or as we call it burp air out. Also, this helps small amount of coolant to get by and always to have circulation through the cooling system and help or prevent static flow. Take well care Scott!
@terencescott39578 ай бұрын
@elchanojose4633 thanks for the info. I finished installing my new thermostat shortly after my last post. I went to check the positioning of the vent hole on my old thermostat. By luck I positioned it at the 11 o'clock position. Bit I'm good now. No leaks.
@sari-saritv.82355 ай бұрын
Thanks for this info
@merchanthandson5271Ай бұрын
Thank you for very important info. Can i make small hole to it same size?
@lorddraako16552 ай бұрын
I bought a thermostat from AutoZone and it doesn’t have the jiggler pin should I install it?
@jfcalix5 ай бұрын
The information what I was looking for thanks
@elchanojose5 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that this was what you were looking for. Take well care!!
@mavadoroaster20 күн бұрын
Great info 👍
@elchanojose20 күн бұрын
Hello! I’m Hank you for taking your time to watch our video and hope this was helpful. Take well care!
@CaratLV6 ай бұрын
i just bought a thermostat for my jeep compass but it didnt come with that silver piece in the hole???
@elchanojose6 ай бұрын
Hello! Some thermostats are not made the same. Some are made different but still work. The only advantage of that little silver valve is to allow air trapped to move by when the thermostat is close. This helps the engine to burp air out and fill the space with coolant. Take well care!
@midwest_nikk268210 ай бұрын
It does that no matter where the thermostat is located.
@user-bn7lp3go4lАй бұрын
Tab always goes to the top at its highest point 👍
@anthonytrejo666 ай бұрын
So the little metal thing has to be open?
@elchanojose6 ай бұрын
Hello! The metal does not have to be open, it would be good and helpful to sit at the highest point when installation. Also, keep in mind that the thermostat be installed in the right way for it to operate properly. Take well care!
@Carpenter_King865 ай бұрын
Thanks homie
@donaldwhiteman32245 ай бұрын
could this cause overheating? if installed with jiggle pin facing downward?
@towcars55505 ай бұрын
I think so I'm waiting on mine I bought one from AutoZone didn't have that lil jiggle...I got one from Amazon and it has it
@donaldwhiteman32245 ай бұрын
it was the cause of my overheating along with the coolant temp sensor. replaced no problems now! @@towcars5550
@TheShangralaaaa178 ай бұрын
the jiggle pin faces upwards so the air can escape
@2STATIC_4LYFE6 күн бұрын
What happens if it's not? Does it cause the fluid to boil out of rad when trying to bleed
@elroco48272 ай бұрын
It should be 12:00. The jiggle pin also helps bleed the vehicle
@TaylorRamirez-uz9fw11 ай бұрын
Pregunta. El Ac De mi carro no está funcionando Sale caliente el aire y tiene coolant y el fan no está running
@luisematos_6 ай бұрын
Great! 👍🏻
@elchanojose6 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that it was great and you liked as well. Take well care!
@MiguelOrtiz-kl1yb Жыл бұрын
Is it hard to install one ?? Just asking cuz I took mine to the shop and it’s been 2 days 😅😅
@elchanojose Жыл бұрын
Hello Miguel! A thermostat is not that hard to replace. Some cars require more labor than other but 2 or 3 days is too much time for this kind of job. The reason on why your car is taking too long for a thermostat replacement, is probably because the shop has other cars that are being worked on and your car is sitting there until a spot is available. Take well care Miguel!
@M.Qambar11 ай бұрын
It takes 2-3 hours at most if you don't know what you're doing
@gta416211 ай бұрын
@@M.Qambarbro. It takes like 20 minutes or less to replace a thermostat. On this type of car.
@M.Qambar11 ай бұрын
@gta4162 Yeah, that's true for me and you, but the original comment obviously doesn't know much about cars so it'll take them longer + i was talking about cars in general not just about this one because some would need a lot more work just to change a thermostat
@elroco48272 ай бұрын
It’s super easy. If you have the funds to pay the shop and you don’t feel like fooling with, then take it to the shop. But if you want to save money, do it yourself. I do a lot of maintenance myself. I’ve learned a lot by watching many KZfaq videos.
@mindofmantae82888 ай бұрын
Thank you
@kenstole460118 күн бұрын
It called as jiggle pin
@elchanojose18 күн бұрын
Hello! Thank you for sharing what it is called! Take well care!
@durantplayz711115 күн бұрын
My stant one doesnt have any hole im so confused
@elchanojose15 күн бұрын
Hello! Not all thermostats are made like the one we showed on our video, some are made without the bypass valve that we talked about. If your thermostat doesn’t have it, don’t worry about that it is going to work fine. Take well care!
@89gt5.017 күн бұрын
In short it’s a bypass.
@elchanojose16 күн бұрын
Hello! Yes, to let the air go by and keep fluid flowing. Take well care!
@user-lr6ks3xn6r4 ай бұрын
Tha k you for explaining the little thing that can be a fatal mistake
@DFWAuto_Hack Жыл бұрын
Someone told me to break this off so my car does not overheat even if thermostat gets stuck closed. It was true. Car wants to overheat but cannot
@kevinhancock4064 Жыл бұрын
May I ask how you know it wants to overheat ? Ty
@Dcdc956 Жыл бұрын
Don’t do this… 🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️ Jesus…
@DFWAuto_Hack Жыл бұрын
@@Dcdc956 lol i did and it worked
@AbelG8781 Жыл бұрын
@@Dcdc956only a dumb mfr would do something like that SMH
@OtherDalfite10 ай бұрын
@@Dcdc956all it does is bleed a bit of fluid over constantly. Not the end of the world
@user-xh2jz6jc4q Жыл бұрын
I don't understand how you can install it the wrong way. You can't install upside down, only a 180 maybe
@KKDriver Жыл бұрын
The thermostat I replaced on my civic literally wouldn’t fit unless the release tab was at the top. Pretty smart engineering.
@sergiocalderon541610 ай бұрын
Thank you dude I just changed mine a while ago🙏🏽
@elchanojose10 ай бұрын
Hello Sergio! Thank you for taking our video and hope this info is helpful for your next replacement. Take well care Sergio!
@chavatoyz641611 ай бұрын
That’s why I have a problem with my truck 😡 I installed it the wrong way!
@Thelost9098 ай бұрын
I just redid it on my jeep to find out I did it wrong to 😂
@2STATIC_4LYFE6 күн бұрын
@@Thelost909what happened when u did wrong, I'm trying to diagnose
@SimonLopez33123 ай бұрын
Hell yeah Brodie
@Travis-bs6hm9 ай бұрын
Thank you for your post
@Codeineworld3 ай бұрын
I need help from you
@waltersmith31659 ай бұрын
Real mvp
@Caleb-lbj11 ай бұрын
I drill it out sorry don't need it can drives better and faster
@elchanojose11 ай бұрын
Hello! There is nothing wrong about drilling it out. Makes sense on having a small hole to let small amount of liquid to go by. I don’t know about making it go faster but everything can be posible. Take well care!
@samgrieg25427 ай бұрын
yeah that mod alone adds like 10hp to the wheel
@alejaz84038 ай бұрын
Does it matter which way you Install it?
@wbforsure21046 ай бұрын
It does matter. The side with the coil spring always faces into the motor. If you install it backwards it will overheat
@elroco48272 ай бұрын
Probably not but I’d install it with the jiggly point facing upwards at 12:00