Very nice, Rog. I’m doing a wet room soon and this is exactly what I needed 👍🏻
@timjaksic87796 жыл бұрын
Excellent work !
@milkman1000014 жыл бұрын
a couple of those solvent welds are borderline too dry for my liking! especially under the floor. however ,thanks for this vid. im doing mine at present using the same tray system.hopefully turns up tomorrow. cheers
@cglees4 жыл бұрын
Thanks Roger!
@javadchohan4 жыл бұрын
I am fitting the same wet room from abacus. I had to raise my former onto a 4x2 base frame to meet the waste pipe height and built a 4x2 kerb with a 50mm upstand to keep the water within and to support the base of the glass screen. On the remaining bathroom floor I have uneven floor joists and after lining with osb I poured over primer followed by fibre reinforced self leveling compound. My dilemma is whether or not to fix 10mm tile backer boards into the floor using kst adhesive without any screws so that I don't disturb or crack the compound. On top of that will be a ufh mat followed by another layer of self leveling compound and then tiles. Any advice would be appreciated 😊
@icarossavvides26412 жыл бұрын
Very informative as usual, the only thing I would like to add is glueing, in addition to screwing, of the support battens just to guard against the dreaded squeaks?
@hots4jc2 жыл бұрын
I love how this guy thought “out of the box”.
@leegooch75454 жыл бұрын
I would loveit if Abacus did a 3 sided 750mm square preformed tray and trap.
@Sirricardo63 ай бұрын
No Leaks as long as the o'ring doesnt degrade. I think I would have preferred to have the trap solvent welded in perhaps?
@darcysmoke5 жыл бұрын
wouldn't fibreglass mat be better for tanking?
@spoonybubble4 жыл бұрын
Hiya what company are you using in the video? I like the look of the tray!
@alshanky Жыл бұрын
Hi Roger have followed a lot of your videos, thanks for detailed explanation and when I say the details I gathered from your videos to a walk in shower installer, they ask me if I am a builder. I have couple of questions. 1. I am restricted on raising my current floor height which is approx 30mm from joists. 18mm chip board, 10mm tiles and possibly 2-5mm adhesive. So I am planning to sink the floor between the joists all through the shower room and use 10mm elements board while have 6mm for the walls. I am planning to use plywood and battens. I also want to put some thermospan or celotex insulation under the floor between the joists. What size batten would you recommend and what insulation to go with? 2. I cannot use a shower tray 30 mm due to height restrictions. What are my drain/trap/waste options with a 10mm floor board? FYI, my new floor will be 10mm elements board + 5 mm underfloor heating mat fully encapsulated with flexible adhesive (total 10mm) and 10mm tiles on top.
@ItsGrantM3 жыл бұрын
Do you need to use tile trim? Will it even be seen?
@samadams93474 жыл бұрын
looks like a great system - quick question, if water did get under the tiles and grout how would it drain away, as the drain lip seems to sit proud of the mat? Thanks.
@stephenc41614 жыл бұрын
it doesnt lol
@anetshutup54752 жыл бұрын
Hi Can this tray be screwed to ply when tile adhesive layed before tanking?
@lp01292 жыл бұрын
Hi Abacus, is it possible to use this test on solid floor?
@mikeoaks1000 Жыл бұрын
Hey I’ve bought a 1200x1200 tray and it’s not flat in fact if you poured water on it the water will go away from the trap. I’d this right?
@alshanky Жыл бұрын
My plumber connected the trap to a 50 mm waste pipe but due to space constraints we could not fit the 4 degree fall connector. Also I find that there is a little water standing inside the trap when I tested for leaks. Is that normal?
@dalefixter2 жыл бұрын
what exactly is that blue paint?
@habibisakhi24504 жыл бұрын
What is called that trap please? Thanks
@jonntischnabel4 жыл бұрын
I want to do my entire bathroom floor in pennies, Including the wet room. Will the epoxy resin be too viscous to work in the fall of the wet room? I don't want to just grout it as the pennies will go dull and green over time.
@MikeCarter2 жыл бұрын
nice idea ... how did you proceed in then end ?
@keithwynne3038 Жыл бұрын
Roger can that system be used with microcement
@AbacusManufacturingGroupLtd Жыл бұрын
On floors unfortunately not no. Its suitable for tiled floors only.
@habibisakhi24504 жыл бұрын
Would you able to send the lists of material used please ? Thanks