Looks good though I would have tried to run the cable below pebble dash level so it blends in more

Great job ,only concern to me is if I was a paying customer I would of insisted the cable was routed under the unmarked rendering in cream.and run along the brick work . End result big black cable not seen on cream wall. But other than that great install.

Kenya's not yet big on EVs but from you and Artisan electric I've learnt a lot to give me base knowledge on this. In preparation for the time the kenyan market will embrace EVs

Nice clean work.

Thanks for taking the time to make this video, as someone about to have one installed by my electrician, it’s good to have something like this as a heads up. 👍

What did you do with the load management CT???

Brill, thank you. Still your favourite EV charger?

The install was great. You guys need to relax, I’m sure if he could make it better he would. I personally found his work amazing and would defo hire him. He knows his stuff so stop hating on him.

Hi mate Nice set uo there ! Is your rcbo double too switch the neutral or single pole ? Ive been told its now part of the regs too supply the zappi with and rcd/rcbo protected circuit that switches both live and neutral conductors! Even though the zappi has built on type a and pen fault its not compliant as the built in rcd is on a circuit board

Great neat job well done. 👍👍👍

agree with the other comments re cable run... should be positioned along the lower brickline plus I'd have used a piece of white conduit to bring it up the wall vertically

Nice job, if I live in a first floor flat, own the leasehold and own the car port below, can one of these run from my flat consumer box to the car port?

Hi, did you provide a Part P installation Certificate to the customer to satisfy Building control?

Only thing I’d suggest is disconnecting the flat cable from the front portion of the charger while you’re installing it so it’s not dangling from the connections just to save anything getting broken. Looks a good job though.

Nice job, mate really I appreciate very much your time also you try to film and do job same time is not easy your own understand that as well but all good

That looks really tidy.. I’m having an ev charger fitted in the coming weeks. I hope they do as nice a job as this.

Good Job geez. I have not installed one yet but I do agree I would have tied in under the wall covering if there was enough cable? that is the only reason not to have done so unless there is another reason but apart from that very neat and nice to see. what benefit to the client is the anti tamper device does it trip the breaker?

No CT clamp on the main tails??

Do yiu not out a CT on the tails going into the EV CU?

Nice job, how about putting the cable in some white 25mm conduit? Would of blended in like a dream.

what is the tamper fit pcb for ?

Why didn't you run the armoured below the dash render, it would have tucked under there nicely, instead they have a long black washing line right across the white wall.

No PEN fault protection needed? TNCS earthing bonded to N

Good video once again,would it not have been possible to run the cable round the red brick so it was under the rendering and less visible or was the gas box too close to the wall for you to feed the cable behind it cable

I guess the level you used has "sealed for life" batteries. 😀😁😂 work's first time every time.

It looks a lot easier to fit than the other types on the market. Quick question, do you need to fit the CT clamps with this make of EV charger? I need guidance in selecting a good, reliable make. Thanks.

Im guessing given i only have a 63 amp mains cutout fuse AND my electric is looped with my neighbour, its a no-go with regards to get an EV point unless im willing to dig up driveways?? 😢

What happens when there is no Internet? Can you charge your car with zapping?

What thickness wire you are using from consumer box to charger?

Why would you choose not to install the ct clamp that comes with the unit 🤷‍♂️ even if its just to future proof it for if they want to use solar features ect later on or incase you got the maximum demand wrong or demand changes if they get new or additional high load appliances

Hi. what size cable sq? Thanks

all the vids seem to show you the easy installations on new build, nothing showing homes built 60/ 100 yrs ago with the meter inside at the back of the house,and the consumer inside at the front in door bottom of the staircase which is about 15 mtrs away from the meter feed entry point

That cable routing will cause a stain to appear on that white dashed wall, l give it 18 month at most

isnt that a camera tripod against the van ?

Why not use a white cable to blend in with the house 🤔

Just watched a video from sota on KZfaq and myenergy won’t except a warranty claim unless the charger is protected by a DP RCD

Still waiting for the follow-up video showing installation of white trunking to cover up the amateur placement of that black cable. You might get more customers if they see you're prepared to make good a poor decision.

Just an obsevation. You fitted the anti tamper PCB but didn't explain what it does. Nice job all the same.

is it ok to buy 22kw version but still charge 7kw output? Just to be future proof?

I agree with others cable could be better installed!

Good job but the cable on that high is not acceptable.

oh man, i can't stand seeing cables along walls like that.

are you autosized to do that.. are you exucated to do this. otherwise this is NOT leagal to do buy you self.

Whats that bush infront of the consumer unit should we be concerned?👀🥦

You say you’ve fitted loads of Zappi’s? Have you done the EV qualification? *No use of the CT for load limiting? *RCBO is single pole - type AC (should be double pole - type A) It’s good to have a base knowledge of the regulations on EV

Hi pal sorry but I just think the cable clipped surface round the wall is an eye soar and I would not have allowed that at my house just pity you could not hide it under the ground then down from main and up to zappi this is not to say you are not good at your job it's just that cable install round the white wall

No DP RCBO and its a type AC 😮

Who did well but that cable could have gone a lot lower it looks horrible like that

Sure it all worked fine but that cable would make me find someone else for the next job. And as the customer I’d probably find myself re-running the cable myself!

I would not be happy at all.....Black cable on a white wall? No. Use white cable or fit to the brick below.

Omg, if he attached that black cable to my house as he has done in this video he would not be getting paid until he reinstalled the cable in a more discreet location and then filled in all the holes in that house wall and repainted it, what a shoddy lazy arse job

Black cable on the wall, not acceptable.

Tardy install. That cable looks a right mess. Run it to the lower level. Just lazy, or what.

OMG that cable should have run at low level on the brickwork. The gas meter is no excuse for running the cable in this way. You could have easily dropped down after the gas meter and run it along the brickwork, you simply chose the easiest option. Your customer will be looking at that cable daily as will everyone else who passes by. Terrible choice and has spoilt the whole install. Also no CT clamps installed because once again you chose the easiest option for you. Not in your customers best interest.

Part of being a good electrician is an ability to hide cable's, not the best install I've ever seen.

The cable routing is a disaster - it should be removed and installed at the pebbledash juncture. I would be ashamed if it looked looked like that.

Mate. That black cable across white wall doesn’t look great. Why wouldn’t you run it lower just under render level?