Get 20% Off with the code JKGG20 stechswitch.com

Just installed 12 Oct '20 and now it includes a jumper for the circuit breaker...well done S-Tech!

Another great video Ben, maybe you should consider a part 2 showing how you route the wires from your accessories and how they terminate and connect at the control box.

Thanks Ben, for this video and the discount code from TTO. So far very impressed by the company and how professional they are and the attention to detail all the way down to the placement of stickers on the box. Definitely raised the bar.

Pro tip* drill a drain hole on the bottom side of the switch panel just in case water leaks in from the Freedom Top. Learn from my bad experience...lol

Ben, I used one of their 4 switch panels when I installed the rollbar. Had to get the switches off the A pillar. Already had a relay box so they sold me just the switch panel which worked awesome. Great company! Thanks for the vid!

use the circuit breaker for what it is , put the the trigger wire on load side, switch on/off when needed

Thanks a lot Ben!! You saved me 75$!!!! Love the videos and can’t wait to install it!

As a new Jeeper, this is a godsend.

Can’t wait to install one in the LJ!!

Love the look of this switch system, definitely going on my mod list

you could use a spdt switch so in one position the trigger wire is keyed the other is hot all the time. best of both worlds.

if you want to be able to do ignition, or do a bypass. you can hook that lead to your M9 lead and put a switch in between BAT+ and that, flip the switch and you can use your switch board whenever

Looks great. I have front spot light, front flood light, rear flood light and a winch. I think I'll order a 4 switch. Thanks for making the video, you saved me $48 with your discount. 3-18-2019

April 2020 coupon code still works saved $67 on a six switch pod and the breaker 🤘🏻

Great video, best bart was how dirty it was under that trim, that's a well used jeep.

What a great option to aux switching instead of deleting the media section for aux switching, thanks

Those switch pods are a must have for jeeps I love mine great video

I use the “Remote” wire set up to run on Accessory. The red looks pretty cool on your red Jeep. As for the switches I’m just going to get the Aux Package when I buy a JL.

Just ordered mine and the discount still works thank you so much !!!

Shoot, I was scared that I was bad with wire management. Glad I'm not the only one. Definitely going on my mod list.

You could use a light bar wiring kit to basically open and close the circuit going to that switch panel so it won’t kill your battery but I guess it kinda defeats the purpose. Or make one of those switches kill and open it

Yeah... very nice install, but (EE here talking) that wire link between the circuit breaker and the power source will not handle 60 Amps... and thus it becomes the "fuse" in the series circuit. You might want to fix that. I would use minimum #6 gauge and #4 if it's really hot where you climb.

Very cool setup I don’t have any electrical accessories yet but this is definitely the way to go..Fine job and thumbs up

God, I wish I had seen this a year ago. Getting ready to do MLC-6, but I like this way better

I have been looking for something like this. I am so glad I found your channel. Also I drive a Taco

This is on my Christmas list now. I just need my wife to sign off on it 😁

Cool man, Love your vids! Inspired me to start my own! Keep em coming!

I like it. I’ve been wanting to get a switch system for my Jeep. Great video 👍

I'm a simple man.....I see the notification and I pull up the toilet seat , sit back and enjoy

I have a great video idea, you installing a 3in lift on my jeep 😂😂😂. I'm gonna get this for myself for Christmas. Thanks for the code

Awesome video!!! I am wanting to get a 6 switch from my 09 JKUS I want to add lockers, lights and an air compressor this system looks awesome

Going to start here with my mods. Thanks👍🏼👍🏼👍🏼

One Tacoma guy right here!

Discount code still works as of 4.3.2022. 😉👍

Get the dual battery kit from Genesis offroad

Just wanted to say Thanks for the video and Yes the Discount Code is still good 😃😃 Just installed my system this past weekend Great and Easy System to install 👍👍

I just used the Code Thanks Ben!

Great video! I have a JK as my daily and I'm always looking for a better way to do things.

2:55 that is where Cassie got the idea from

BRO! REALLY? You're not going to show what you did with the accessory wiring? That's the most important and hardest part there. You need to discuss but end and other connectors, gauge of wire for the extensions, zip ties, wire protectors, Where to run and why due to different factors and Heat in the engine which jeeps are known for melting stuff and images of all that.

You had a lot of sunlight behind you when you started.

Just turn off the circuit breaker when parking it that’s what I do

I just ordered mine tonight and the JKGG20 still works!

Great video I'm watching it to see how you cleaned up the wires and used the relay box. As far as the little lites staying on I had the same issue. I went back and added a small toggle switch onto the switch panel. So far that has worked.

Great tutorial, vary clear to the point. Thank you for sharing.

First order of business should have been pulling the ground from the battery. Lol-

Don’t forget to show the next review video on this!

You said earlier you had A-pillar switches. Have you thought about routing the new multi-switch system through one of the A-pillar switches to kill the power to the multi-switch?

Coupon Code still worked thanks so much!

Run a switch for the trigger wire and put it where the 12v outlet is?

Hey love your vids man keep up the great work, I had an idea for your red lights on the bottom always staying on, what u could do instead of running that little red wire straight to the battery with the big wire run the little one to a switch inside which acts like a main power to all your switches which will turn them off until you flick the switch then they all are on. That's what I did in my car just to keep my battery from dying I eana main switch to activate all the other switches and works amazing so u still have the option to run lights when the car is off

Just got my S-tech system all installed and setup, although now I am faced with the struggle of trying to connect those switches to my lights themselves. The switches seem like single wire connectors while the lights connect via a three pronged peice, any clue how to solve this?

Would an update video on how your engine bay wiring looks after cleaning the wiring mess be worth doing??

Any issues with water getting into the switch panel with the top off?

a question can I but tow led light in on relay and fuese or should keep every led with deffifernt switch relay fuels Al's type of cable should I use 16gb

This video was perfect 👌 thanks for sharing .

Hey Ben, another great video. Maybe you already mentioned this crap but i'm too lazy to fiter these comments. I just got off the phone with S Tech. Great company, they called me back instead of writing back. I mentioned I watched your video. I was actually contacting them about using the 60Amp breaker. I hear they contacted you so we both know what to do now. I asked! Coupon valid till end of 2018. I know you're now in Florida (prior Alaska). How about a Winter Snow Run video? (Oregon Native)

Thank you JK Gear and Gadgets for the discount code! I ordered mine. I have had one on my list for awhile now and the discount made it for me. Now to install. I was wondering if you could have it both ways, turn it on/off at the switches without the ignition and always have it come on with the ignition?

how do you hook up your diff lockers to those lights?

Each switch should have it's own fuse no? I just bought a 4 switch toggle set up and they say daisy chain the positive terminals as well as the negative ones and to have one line for each coming out of the end terminal, one for positive lead, one for negative lead, however each switch is rated at 20 amps, so each switch should have like a 15 amp fuse, not one fuse in the lead coming out for all 4 toggle switches, so Im stuck not knowing what to do?

How to connection a wire to switch rocker?

I see you already have extra switches mounted on your pillar Are you going to keep those as well ?

sweet mate looks the goods! Thanks for the vid 👍

Good video. Not sure how useful the 12v USB ports will be as you will need to run a long charger cord down to a phone or something and it may be in your way while driving

Good job.

Very cool man👍

What are you going to do with the A pillar switches? You could use one of those to control the small hot wire to the S pod so the systems energized on demand regardless of ignition on or off. I'm running the Apollointech system with the built in ammeter and love it. I did install the fuse tap that came with it, just one more level of protection in case of a short to ground. Needing the ignition on has not been an issue for me. I do like the way their switch bank mounts, mine has the bracket over the footman's loop and it interferes slightly with the freedom panel latch but not enough to hurt anything. The one thing I want to figure out if possible, is how to put a dimmer on the switch bank, they are fairly bright at night it would be nice to tone them down a bit.

So let me guess. One wire connected from the battery to switch board will do all the work .

What Jeep model do you have? It's super clean

Daddy ben I want this for Christmas can you tell Santa?

I've been running the S-Pod system since they first his the market and love mine, dunno is yours has the same thing as mine does, but to the left of my first switch there was what looked to be a screw in fuse/ reset looking button. I didn't like the lights bring on all the time and was looking at it one way to figure out how to shut them off. To my surprise that fuse/rest looking thing turned out to be an on and off switch for my lights on the pod. Nowhere in the instructions did it say anything about this. I didn't notice it right away cause it blended in with all my black plastic and the black on the aluminum switch pod. Maybe something to see if yours has the same type of small button??

Does anyone make a mounting plate for the S-Tech Switch System and the ARB dual compressor

Used the discount code to order mine should be delivered soon set mine up custom also went with red and blue switch’s blue for lights red for future lockers also side question how’s the aux beam rock lights holding up for ya I have a 03 Tj I’m Ls swapping on 37’s

I like the video, but the install of the circuit breaker was a let down. The fact that you used a smaller gauge wire from the battery to the breaker (vs the larger wire from the breaker to the switch box) is a bad idea. Now the circuit breaker is the smaller gauge wire, and not the breaker it's self.

So how often do you run your rock lights and air compressor with your engine turned off?

Thank you

I was about to ask why your ears were glowing when I realized it was the sun... 😂🤣

So when is the full cage and offroad racing seats and seat harnesses coming safety is number one for off-roading

Just flip the breaker when not using the vehicle. Turn it back on when you need to.

Looks good Ben how many amps is the. Circuit breaker

I have a question that nobody has been able to answer for me yet or if it is possible. I have a enclosed cargo trailer with several lights inside and out that are hooked up to switches and a battery so it can run lights without truck. The lights on the back of the trailer are hooked up to a switch in trailer but we want to also hook the lights to our reverse wire from truck so they come on when we backup. Do I need a relay or would a 3 way switch work? I figured with truck battery and trailer battery I would get some kind of back feed to me 2 way switch that I have now.

Are you sure that is a big enough power wire to the circuit breaker?

what are the fenders on this jeep. I wanna get a set.

i like your rocker switches better yhen ones on my SPOD

hey man, wondering how u hooked up ur ARB twin Air compressor to this s-pod.

Hello, I need a reviewer for my rocker switch panel, would you be interested?

Ben, do you think the 24 inch battery cable for the 60 amp breaker is long enough if I mount the switches where you mounted them inside the cab?

were can I get the same fenders

Was you able to get rid of the relay that came with your compressor and your lights? And just use the relays that is on n your pod control box?

Just recently got our a-tech system shipped to Australia and installed. Just wondering how to terminate the spot lights to work with only the high beam signal? This is a requirement for Australia. Can anyone show me which is the correct side of the high beam line to tap into?

The template isn't to scale

What size wire did you use to go from circuit breaker to battery? Is mentioned in the instructions?

Just ordered the 6switch model... Guess I have to mount the radio somewhere else...

So you still recommend these switches? I Looking to pick up something that won’t give me trouble lol

Whats that RED tarp looking thing you have above the switches? Looks like a shade top?

i have a cb mounted where all these switchpods are made to be installed. Do you know if i could purchase an A pillar switching console but use the "brain" of S-tech? are all these switches one standard size?

Sounds like you've been using S-Tech setup for a few months now. How's it holding up?

@jk Gear and Gadgets can I get 3 position rocker switches for this? I have some aux reverse lights that I can turn on auto (w/reverse) or flip the other way when needed (not in reverse) and I'd like to keep this setup.

Would you say that the 4 switch system is enough? I’m not sure what I will add in the future but I don’t want to run out of room if i go with the 4