Installing Mulch Kit On 54” Deck. John Deere 1023e 1025r Tractor. See in Use Vid Below!!!!!

Рет қаралды 35,544

Robert Munoz

6 жыл бұрын

Watch this for Mulch Kit In Use
• John Deere 1023E 1025R...
My John Deere Attachments • John Deere 1023e or 10...

Пікірлер: 43

@generaldistrust 4 жыл бұрын

I clean & grease the blade bolts every time we sharpen them. Makes life easier.

@stevekopcial129 3 жыл бұрын

What a great idea, I will do that next spring...

@generaldistrust 3 жыл бұрын

@@stevekopcial129 also anti-lock solutions but they're out of reach for me so I use grease. The threads direction in relation to the forces shouldn't let these go loose if you tighten them just enough with an impact drill or a suitable torque wrench without overkilling it. Much luck!

@URanInTheUglyForest 4 жыл бұрын

Great video! The next time you get a frozen nut or bolt, apply Kroil and let it soak in for a while. If it's really stubborn or badly rusted, let it soak for a couple of hours. You might find it at your local gun shop or you can get it on Amazon. It's not cheap, but it works. I find it superior to PB. As mentioned below, anti-seize is a great idea. I use it on any bolts that get exposed to the elements.

@ordinarynonplayercharacter2142 3 жыл бұрын

I put the zerk fitting grease gun grease on the blade bolt threads, never lost a blade. Never had an issue loosening the bolts. I’m sure it’s not right but it works.

@deborahfallon6065 5 жыл бұрын

John nice video. Couple of things you are doing, over tighten the bolts on old blades, 50# torque on these bolts. Should use anti seize on bolts. If you have the correct tap, should run it in each support for the blades. Used a torch overheats and cooks the grease and seals in the support. Heat is LAST choice. Impact guns are a no-no for tightening. Let PB set over night and spray couple of times. Tap bolt lightly to shock it. This will let pb get into threads and help release. Last thing ANTISEIZE the bolts and use torque wrench. Torque to spec. NIce video and help info.

@JohnnysTipsandTricks 5 жыл бұрын

Thanks for the info.

@StringBanger 3 жыл бұрын

You need a DeWalt DCF899B. I have one I keep in my truck that I use to break away stubborn bolts but the situation can be avoided by simply using anti-seize and torquing them to spec so you know you will be able to break them loose when needed.

@mofo9886 2 жыл бұрын

Great video, thanks This looks easier than I suspected it was going to be

@jasonbyu75 5 жыл бұрын

Heat and cool with new application of penetrating oil and be very careful about fire.

@jpbarley 6 жыл бұрын

drive over deck makes it so nice

@JohnnysTipsandTricks 6 жыл бұрын

Love at first site ❤️

@northernbear7627 5 жыл бұрын

A little tip, Use WD40 on the under side of the mower deck and it will keep the grass from sticking.

@reddogrg 3 жыл бұрын

Get the 1/2" drive Milwaukee 18v fuel impact, guarantee it will be tight enough

@christophernickum 5 жыл бұрын

Good vid. How do you open and close the baffles? My X380 has wiring and a switch on the console but I am upgrading to the 1023E and would rather there be a simple manual open and close, particularly since I will be taking the deck on/off more frequently

@qfdforme 5 жыл бұрын

Two words. Anti-seize (for the blade bolts) Torque wrench.

@redgeminipa 5 жыл бұрын

Agreed. If he thought the middle one was bad before, it’s going to be 10 times worse when it’s time to change them again.

@generaldistrust 3 жыл бұрын

As we don't have this solution at reach -we use grease. It helps, and it's way way better than nothing I guess

@jackfunderburk4177 3 жыл бұрын

Everybody worried about torque and oil but I'm thinking u put blades on wrong... Been a while for me on mulching blades but I thought cupped part of blade went upward....

@johnconroy4467 6 жыл бұрын

FYI, there's a torque specified for those blade bolts. I have a 48" deck and the torque is only 50 ft lbs, which isn't a lot really and looks like way less than you put on yours. You don't have to work so hard, man! Great video though, thank you!!!! How well did the kit work? Were you satisfied with the mulching results?

@JohnnysTipsandTricks 6 жыл бұрын

Didn’t know about the torque rating. Thank you, I will check it out and be careful next time. The kit worked great. It feels a bit different with the kit on. What I mean is, it vibrates occasionally and I keep thinking something is wrong but there’s nothing wrong. The results are much better than I expected and I mean much better. When I cut tall grass there seems as there is nothing there so I would recommend 100%. I am planning on doing a vid on it this weekend to show the results. Subscribe if you haven’t yet. If just started putting on my tractor videos with attachments. I have a few on now, check them out and tell me what you think. Either way good luck and thanks

@elained2448 4 жыл бұрын

Mr. John, we just picked up a 1025R and the salesman said no mulching kit available...if you could find a part number, I’d sure appreciate it!

@JohnnysTipsandTricks 4 жыл бұрын

I believe it is BM20827. I don’t have the paperwork any more but it looks right

@JohnnysTipsandTricks 4 жыл бұрын

That definitely the one I have on my tractor

@elained2448 4 жыл бұрын

Johnny's Tips and Tricks thanks, the salesman said I needed to buy another deck to mulch with

@JohnnysTipsandTricks 4 жыл бұрын

Call Buck Bros

@elained2448 4 жыл бұрын

Johnny's Tips and Tricks I’ll look them up, I’m guessing they’re not in NC

@steveconsalvez4320 3 жыл бұрын

My friend. The manual states 50 pounds of torque. Unless you're really wimpy, which you do not look like, you're maybe putting in 80 pounds. It's way too much...

@xsrdxvideo 5 жыл бұрын

Thanks!

@JohnDeereR-zw3wj 2 жыл бұрын

No need to tighten the living jesus out of those bolts!! Even my Ryobi 18 volt impact driver is too much at 150 ft/lb of torque. Also, use anti-seize on those threads!

@lgm2912 11 ай бұрын

You're using the wrong impact gun. That one is too small

@garybaumann5637 4 жыл бұрын

What too tight on those bolts.

@lackeylawncare7826 6 жыл бұрын

Dude.... you put those blades on waaaay to tight!!!. Literally need to be hand tight. No way you will ever be able to change blades without taking deck off each time

@brantner22 6 жыл бұрын

What is the part number for the mulch kit and where did you buy it from?

@JohnnysTipsandTricks 6 жыл бұрын

I don’t have the part number on me right now but I bought it at buck bros.

@RageQuitSon 2 жыл бұрын

there are torque specs...

@vicvary 6 жыл бұрын

good video but maybe when u banging on the hammer mover the kid

@JohnnysTipsandTricks 6 жыл бұрын

I know your just looking out but the angle of the camera doesn’t really show how far away he actually was. I could have swung the hammer like a crazy man and he couldn’t have gotten hit.

@JohnnysTipsandTricks 6 жыл бұрын

Mower ....mover. Very funny. I just saw it 😀

@JohnnysTipsandTricks 6 жыл бұрын

My John Deere Attachmentskzfaq.info/get/bejne/qbGPlKaaxtLadpc.html

@northernbear7627 5 жыл бұрын

Another plastic for a plastic tractor.