Looks easier in this video than it is depending on your type vehicle. I strongly suggest discarding all the hardware and getting 1/2 inch self tapping screws. You may or may not need to drill pilot holes if pedals are metal. It will save you time and headache! Plus the chances of them coming off are slim to none. ( I purchased a different type of pedal with multiple holes which made the adapation easier.)
@nolancoates8080 Жыл бұрын
Very nice work!!! It looks relatively simple to install and I agree with the previous comment about adding split washers
@djayzul Жыл бұрын
Thank you !!!
@darrinfaulkner8911 Жыл бұрын
These brake and gas pads are dangerous.Depending on the model car one has my new pads were too close on my gas and brake pedals my footwear would at times press both pedals down I thought I had to just get used to them but I was sadly mistaken.I was approaching a stop light and went to hit my brake instead I accelerated right into the back of someone car my headlamp cracked and left front bumper is hanging off the other car had minor scratch and didn't pursue any insurance payment. I explained to him what happened it was an innocent mistake my drivers license been clean for over 30 years.I will start my own repairs tomorrow. I've taken those dangerous pads off my car so be careful with using them.
@roadtojdm7 ай бұрын
Both you guys forgot to take off the black plastic rubber on the brake and the gas pedal,which will cause these covers to slip off,and the nuts come out fast with strong vibration caused by the rubber padding.i had to learn the hard way..they should tell people this in the directions
@wildwildwests6 ай бұрын
Ok so they need a warning “Must have common sense to operate “ 😂
@kash6625 ай бұрын
@@roadtojdmwait so that whole black piece needs to come off? Like only the red piece is needed?
@xerodanger39755 ай бұрын
@@kash662nah he’s talking about the factory pedals. Some cars (mainly older), the foot pad on those pedals aren’t attached to the pedal arm usually just snapped on like a lego piece
@Ann-ub4mf2 ай бұрын
Thank you.
@everettbaltzer79282 жыл бұрын
I bought the same exact ones for my 96 F-150, but the holes on these aren't spaced enough for the existing pedals...
@modestlythor91037 ай бұрын
Not fitting on a tundra neither
@lordalfredopelario81242 жыл бұрын
I tried it on my truck.. seems like its not a good fit.. but it says on the package it can be installed on Cars, SUV, or Trucks.
@merkadioe9806 Жыл бұрын
so effing cool! Looked complicated but you made it look so smooth to install :)
@Issy41ify Жыл бұрын
Thank you! Very helpful I was breaking my head for a sec.
@wahidiphone Жыл бұрын
good video, specially you managed to get the camera lens focus back of the paddle at the end, great! 👍👍👍👍👍👍👍👍
@arthurforteza39122 жыл бұрын
Good fit, jus noticed you did not apply fliers to press the metal plate against the back pedal as shown in the manual, no longer needed bro?
@BateMasterJeff98872 жыл бұрын
Huh?
@dogwater10892 жыл бұрын
He did apply them, its even shown at the end of the video
@AstroTiddies11 ай бұрын
Well this was extremely helpful 😭 I was scratching my head at the given directions..took me 5 minutes after watching this video 📈📈📈
@lloydchambers59133 ай бұрын
lol me too i was like wtf are they talking about on box
@wimmeraparanormal65812 жыл бұрын
I strongly suggest to buy a pack of mini split washers to add onto the nuts, to eliminate the nuts vibrating loose over time and to finish the tightening with an electric screwdriver set to max torque, just so the tightening is quick and less awkward.
@alexandrubalanDBX2 жыл бұрын
Hi! Very good idea but can you please send a link with the Mini Split Washers ? I was trying to found some but nothing on amazon or ebay. Please if you have time just to send a link and the good size. Thank you
@grimeallday9362 жыл бұрын
@@alexandrubalanDBX m3 washers
@darrinfaulkner8911 Жыл бұрын
You're absolutely right because my new brake pad cover screws loosened in two areas after I tightened them and it can be dangerous while driving if pushing the loose brake pad that's touching the gas pedal causing the car to unexpectedly accelerate.
@wimmeraparanormal6581 Жыл бұрын
I have now removed these and gone back to the original factory pedal covers because the color fades easily and looks very ratty. Very poor wear-resistance with these color metal covers. They only look good for a month or two
@fuegojay12102 жыл бұрын
Something I need, but the way you secure it I feel can be better
@Le4thl3 Жыл бұрын
Do you need to remove the original rubber off the pedals before you place the new ones on? Or does it just go on top ? Many thanks
@djayzul Жыл бұрын
Just go on top. Thanks for watching!
@Theantonioleyva2 жыл бұрын
you made it look easy I just got the grey ones on the mail!
@Shiroyashasama3 жыл бұрын
I bought the same ones for my 2010 accord and the brake pedal cover is giving me hard ass time cuz it doesn’t cover it fully
@liamcampbell44853 жыл бұрын
ok
@Nate02892 жыл бұрын
I have the same car and I’m having the same problem. Did you get them on?
@Shiroyashasama2 жыл бұрын
@@Nate0289 no I just took them off and put them away I’m gonna buy different ones
@gussng77852 жыл бұрын
Having the same problem with my 04 accord coupe
@dakeibragimov3697 Жыл бұрын
Молодец четко и ярко все показал
@windsurfredbull11113 жыл бұрын
So do you need to remove the pad on the pedal itself to apply this or should you leave the pad on
@djayzul3 жыл бұрын
No need to remove. Just leave the pad on.
@djayzul3 жыл бұрын
Please subscribe for more videos. Thank you.
@robertjebediahfreeman2 жыл бұрын
It depends on the size of the pedal If it is larger then you may have to remove it
@ericfoote30662 жыл бұрын
Very helpful, I have the blue sport pedals
@jeromewalters19382 жыл бұрын
I bought these exact ones for my 2019 corolla the gas one fits great but the brake one pain it falling off and I to cut because it was too wide
@JohnEBlaze-ow5tp2 жыл бұрын
I got a 2011 Nissan Altima and the brake pedal gave me a hard time too but after over tightening it I got it to stay. The gas pedal is the one fighting me. It don't matter hoe tight I get it the damn thing won't stay. I even tightened it so tight the screws pulled through. It's in the passenger seat til I figure out what I'm going to do to make it stay.
@alikdouh369 Жыл бұрын
Would this fit in Toyota corolla 2014 hatchback
@dennismartinez81898 ай бұрын
Muchas gracias muy bien espléndido excelente
@checodogface Жыл бұрын
a large metal surface is very slippery so i dont understand as the bottom of shoes are all rubber for a reason seems more slippery then original ones
@rebeccadennis64772 жыл бұрын
thank you for this video! I needed it!!
@4000mack2 жыл бұрын
Thank you, really needed this!
@nativelibra6265 Жыл бұрын
Any advice for a 2007 Mercedes Benz? I got the screws in & that's it..😂
@willievasquez27492 жыл бұрын
Thanks for that back view at the end needed it have a nice day #🔵
@lloydchambers5913Ай бұрын
great video but now the brake pad one keeps loosing up n falling off any suggestions ?
@dekomstou87411 күн бұрын
Threadlock or plumbers tape
@ernietagra4637 Жыл бұрын
Karon kabalo nako onsa.on pagkabit😁😁 slamat idol
@jobertlima52974 ай бұрын
No meu reforcei com fita dupla face ficou top
@marthytapena64708 ай бұрын
It was very explainded. Thank you
@Alex-ts2 жыл бұрын
Perfect job mate
@djayzul2 жыл бұрын
Thanks mate. Please subscribe my channel. Thank you.
@EduardGongora Жыл бұрын
Gracias!!..no te is ni idea cómo era que se ponían jj 👍
@Lifesabitzh Жыл бұрын
Thanks 4 the video my 1s didn't come with instructions
@hambaallah40482 жыл бұрын
very helpful 🙋🏻♂️🙋🏻♂️ thank u so much 🙋🏻♂️ from Malaysia "
@djayzul2 жыл бұрын
Thanks sir.. please subscribe my channel. Thank you.
@mizzcamillionaire71802 жыл бұрын
I tried putting it on but it’s hard
@shekhar_19842 жыл бұрын
kwid climber ko laga sakte hai kya ?
@hikbandzz5 ай бұрын
i don’t this works on my lexus es 300😢
@tastemakerguidie9 ай бұрын
Sandle Knotting Is Opinionated Although Brake Is Greater Velocity Adjustment To Clutch From Cruise Slow
@tastemakerguidie9 ай бұрын
Free Suspended Knot Left Large Toe Socked Smoother Clutch
@tastemakerguidie9 ай бұрын
Magnet Density Matters
@vietnamtoidau6416 Жыл бұрын
thanks for video, but after i installed i did not feel unsafe when drive the car like that, i take them off. Thank you anyway
@faisalfakrul3556 Жыл бұрын
Thankyou i just ordered this at shopee and hope it works well
@diegoarmando40662 жыл бұрын
Thank you so much!
@mohanadnegm65422 жыл бұрын
hello can it fit corolla 2021 brake is 8cm length 4cm width accelator 5.5cm length 8cm width
@daffydlandegge3843 Жыл бұрын
Why dont they come with lock nuts?
@Sub4munneyy Жыл бұрын
Ohhhhh damn I thought it just came with a cover.... not a pedal too!
@TheFreebird2411 ай бұрын
How do you take off the old gas pedal. It doesn't shoe. And I tried looks like a pain
@wildwildwests6 ай бұрын
Uhm, u don’t. These go over the existing pedals
@tylergeorge92663 ай бұрын
@@wildwildwestslmao
@fitzbanton77112 жыл бұрын
Thank you for your help and I love gas pedal and the brake pedal too
@shangkarikrishnan8254 Жыл бұрын
Very helpful thanks
@tenseventy49 Жыл бұрын
Thanks a lot!
@Angeltui Жыл бұрын
We try and try and try and it’s so hard to put them on😢 we can’t put them on. I will go pay some one to do it for me lol cause it’s so hard tan put them on😅
@saman.ak20032 жыл бұрын
what's the another name use for padel brake?
@jinetikzgames Жыл бұрын
Will this work my 05 nissan altima?
@yolandagaines16782 жыл бұрын
Thanks you. Great video. It helped alot
@djayzul2 жыл бұрын
Thank you 🙏..
@se7ensamurai2 жыл бұрын
they look pretty thin and cheap, hoping for a quality assessment, but that's ok. thanks for the video
@phillipdady3039 ай бұрын
Very helpful. Especially since I have the exact same ones except mine are blue
@henrypiedrasanta84022 жыл бұрын
Thanks a lot…..very helpful….got the silver for my 4Runner
@christy121693 Жыл бұрын
I jus put the blue ones on my 98 4 lrunner
@saman.ak20032 жыл бұрын
what's the synonyme padel brake?
@AR1GAT02 жыл бұрын
nice, how did you film this lol
@georgerios6847 Жыл бұрын
Thanks
@TutoFree Жыл бұрын
Link please
@number-uz1es9 ай бұрын
I bought these off shein for really cheap- but after reading the comments I’m just not gunna bother installing them I rather waste $3 then $$$ getting my car fixed due to negligence.😢
@jacobturner4482 Жыл бұрын
I was going to buy these but they seem dangerous considering the bolts can become lose while driving 😢😢😢
@MountainJohn2 жыл бұрын
thanks for not showing us how you took off the plastic.
@JonathanSanchez-uk3xr2 жыл бұрын
touch screen car pedal to put your feet on levitate car pedal
@nrcz3 Жыл бұрын
I got these and i am not happy. They only look good but they keep coming loose and it is hard plastic very slippery. They should not be called Non-slip
@rogervillanueva55432 жыл бұрын
Good job.tnx bro😂😊
@djayzul2 жыл бұрын
Thanks sir for watching. Please subscribe.
@jasongrowden5000Ай бұрын
I got these for 4 dollars on temu
@Jad-KoolАй бұрын
Amazing.
@Geno_Tracks11 күн бұрын
💀
@user-ys5sv4dw4c8 ай бұрын
กิ๊บล็อคฝากระโปรง
@mauriceriz9852 жыл бұрын
Selalu tertangal yg dkt padel minyak hmm
@Sarahstarr10003 жыл бұрын
Good video thank you
@djayzul3 жыл бұрын
Thank you Lil’ Sarah Starr. Please subscribe my channel. 😉..
@Sarahstarr10003 жыл бұрын
@@djayzul ok!!
@djayzul3 жыл бұрын
@@Sarahstarr1000 thank you
@jonathanstrait582 жыл бұрын
This was video was useful
@djayzul2 жыл бұрын
Thank you ☺️
@VEGA-J Жыл бұрын
I didn’t get my hardware
@saman.ak20032 жыл бұрын
just orange color
@johnpaulmeneses62342 жыл бұрын
Sir ano sasakyn wrong kinakabitan mo
@djayzul2 жыл бұрын
Vios sir
@christy121693 Жыл бұрын
I jus put my on there was a bitch to put on but he did it so effortlessly
@godschosen18772 жыл бұрын
After watching your video I'm about to trash those shitty instructions thanks
@ypcteezie Жыл бұрын
THESE DO NOT I REPEAT THESE DO NOT WORK FOR ANY DODGE CHARGERS OR CHALLENGERS
@prmovieelite72402 жыл бұрын
The don’t look safe 🥺for my opinion
@JAY-lu3cx2 жыл бұрын
U right I brought these but know if I should put them on