What a great interior light upgrade. Thanks for the video.👍

I'll give this a go next weekend, nice one Dan

Will be fitting mine at weekend thanks Don 👍

just done my front interior ones today, lovely. next will be number plate lights

Just done my Interior lights with the led lights and what a differents it makes thanks so much for doing this video 👍 have you done a video for the main lights ? i find my lights on my Qashqai a bit dim

Left to go to work today and saw one bulb was gone on my number plate. One quick view of this video and I managed to do them both myself! The shorter right hand one was a right pain in the bum to do and I have tiny tiny fingers😆But they’re all done and I was right chuffed I did them myself- I’m a cack handed woman and still managed 😂 Thank you!

Done this for mine today, looks great! You weren’t joking about the number plate lights being a bit fiddly - mine was short too on the right hand side, I just about managed without any tools.

I had the same issue on the wire on that side... man it was short... i had to struggle with a screwdriver for a long time... a real nightmare.

Hope you don't mind me including this here Dan, not wanting to step on your toes at all or use your platform, just to let others know about the rear interior lights. I have a 2016 reg J11 and just completed removing all the yellow looking interior lights and number plate lights with LED's (bulbs as listed by Dan for this video). The back seat overhead lights are working so I changed the festoon bulbs too. Removing the rear interior lights- I took the drivers side one out first and made it much harder than it needs to be, so I'll go to the passenger side rear light. After taking the light fitting out (it came out quite easy), leaving the cable fitting attached, I unscrewed the tiny screw (seen from underneath the fitting) holding the clear plastic in, and next to that is a little plastic tab connected to the clear plastic. Pushing on this makes a space around that edge of the light fitting to get a small screwdriver in. Moving the screwdriver along toward one of the four pieces of clear plastic holding it to the light fitting, I gently lifted the plastic until it came off. I was careful as I recalled Dan said they can break easily. You can now take the old festoon bulb out and put in the LED one, making sure the yellow part of the bulb will face outward for when the fitting is replaced. I tested the light fitting before replacing any of it and it worked so I put the clear plastic cover back on, refit the screw and pushed the light fitting back in. Again I tested it and these LED's are so much better. Big thanks to Dan for letting us know how to do these things, you're a gentleman. I also had the same problem changing the bulb on the right side number plate light as you did, but it is doable as I am crap at doing these sorts of things. My tip, make sure you have all the nescessary implements before you begin. I wasted 5 minutes trying to find my needle nosed pliers for that awkward bulb fitting.

I don’t know if they changed the light cover in the 2015 model, but mine doesn’t fit back on properly with the LEDs installed, need the slightly shorter, 4 LEDs.

I found some led bulbs on Amazon that cover most interior and number plate lights they are just echt can-bus error free LED SMB bulbs kit set of 22 bulbs everything you need to brighten your car

Great video, question does your dome light come on every time you close and reopen your door? On my qashqai I sometimes find the dome light not coming on.

Would the short ones you linked in the description fit into all the other ones as they look slightly chunkier.

Would the shorter 501 leds still be good for the rear license plate lights? It’d save me from buying separate pairs as I want to change my boot light too.

Hello Any update on the led lights? For the interior and exterior? Any faults? Any changes? & do you use can bus leds for the lights in the back seats and boot?

Hi Dan, I did the 3 interior bulbs today but the covering isn't pushing back up the full way, I am using the same ones as per your link, any ideas?

In addition... Those vanity mirror LED bulbs you told me about, I got four of them (in a tiny pack) and they do fit. One problem, the one I tried to fit blew the fuse (when it went in) for all the interior lights, and the dash cam, not sure if anything else went with them. I have had a go at removing the glovebox but for some reason it does not want to come out. I have been in touch with the supplier of the LED's and they said turn the ignition off... and have the light off... yeah, okay, not sure how that can happen with this car. I don't know if you have any suggestions Dan as how to get around this problem. DOH!

Completely different question here. Any idea how to fix the back window washer? Getting no spray so I'm assuming there's a loose connection somewhere. Cheers

Hi Dan! Can you go through the process of a hill start? We have a Qashqai 2018 Electronic hand brake plus autohold. Many thanks Alan

Link to rear passenger bulbs on amazon is dead can you please update ?

My goodness how fragile car's are to-day. I changed the tail lamp on my pulsar after a struggle to get the plastic lens off without braking it. A few months later I changed the other side, but now it was winter therefor the plastic lens was now brittle and bingo! It broke, bugger. I am getting I am to scared to tackle what should be the simplest of jobs on my car.

I take it that the shorter bulbs will fit the interior cab light? Saves anyone buying two different bulbs???

I Wish I had done some research first mind, went straight out and bought all philips led bulbs which have a habit of staying ever so slightly illuminated even though the interior lights are off 🤦‍♂️

Never used an Electronic hand brake before

For the rear passenger light on amazon I get multiple options, 31mm 36mm and so forth, could you help me choose the correct one sir? 🙏🥹