No video

Intro to SubD using Inset and Fill Holes commands in Rhino 7, full course at www.Rhino3D.Education

  Рет қаралды 16,742

Rhino3D.Education

Rhino3D.Education

Күн бұрын

Пікірлер: 12
@gilbertvales8161
@gilbertvales8161 2 жыл бұрын
Thanks for the tutorial, I am very grateful because it explains it in a past and highlighted way, I understand Utd well since I have a slight hearing impairment. Greetings.
@lyrana
@lyrana 2 жыл бұрын
Even before I saw this was McNeel Miami I knew it was Andres! Love him! Professor "click click" 😄
@Rhino3D.Education
@Rhino3D.Education 2 жыл бұрын
Thanks a lot Lyrana, how are you?
@olgam4458
@olgam4458 8 ай бұрын
Thanks !!!!!
@yazer336
@yazer336 3 жыл бұрын
Thank you
@Vanastarr
@Vanastarr 2 жыл бұрын
Great video.
@Serbo-Greek
@Serbo-Greek 2 жыл бұрын
Op-set diz sudbee... :D
@geoffreynewland6204
@geoffreynewland6204 Жыл бұрын
At what point does it show you how to 'fill' a hole as suggested by the title?
@Rhino3D.Education
@Rhino3D.Education Жыл бұрын
Around 2:30 min
@jkjilali
@jkjilali 9 ай бұрын
how about the hole in the bottom
@Rhino3D.Education
@Rhino3D.Education 9 ай бұрын
Make it a Nurbs and then substrate a cylinder from the base !!!
@jkjilali
@jkjilali 9 ай бұрын
@@Rhino3D.Education thank you
SubD flatware in Rhino 7 (speed model)
4:14
RhinoGuide
Рет қаралды 27 М.
Intro to SubD geometry in Rhino 7
3:55
RhinoGuide
Рет қаралды 56 М.
Чёрная ДЫРА 🕳️ | WICSUR #shorts
00:49
Бискас
Рет қаралды 6 МЛН
Little brothers couldn't stay calm when they noticed a bin lorry #shorts
00:32
Fabiosa Best Lifehacks
Рет қаралды 21 МЛН
This Dumbbell Is Impossible To Lift!
01:00
Stokes Twins
Рет қаралды 36 МЛН
NURBS vs SubD Surfaces in Rhino 7 #200
9:16
PJ Chen Jewelry Design
Рет қаралды 30 М.
Very Important Rhino Commands - 1
4:00
The Adam
Рет қаралды 34 М.
Rhino 7- SubD, Rule of Three
15:20
Rhinoceros3d
Рет қаралды 10 М.
SubD Trellis Ring
30:00
RhinoGuide
Рет қаралды 29 М.
I didn't know LightBurn could do THAT!
16:12
The Tinkerverse
Рет қаралды 73 М.
SubD Quick Sketch Models- 3D Modeling with Rhino 7 #238
11:07
PJ Chen Jewelry Design
Рет қаралды 36 М.
Rhino 3D Tutorial: How to Make a Form using SubD in Rhino 7 WIP
8:42
Surface Modeling with Fusion 360
13:35
Autodesk Fusion
Рет қаралды 1 МЛН
Чёрная ДЫРА 🕳️ | WICSUR #shorts
00:49
Бискас
Рет қаралды 6 МЛН